We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • I.S. EN ISO 20344:2011

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    PERSONAL PROTECTIVE EQUIPMENT - TEST METHODS FOR FOOTWEAR (ISO 20344:2011)

    Available format(s):  Hardcopy, PDF

    Superseded date:  17-12-2021

    Language(s):  English

    Published date:  01-01-2011

    Publisher:  National Standards Authority of Ireland

    Add to Watchlist

    For Harmonized Standards, check the EU site to confirm that the Standard is cited in the Official Journal.
    Only cited Standards give presumption of conformance to New Approach Directives/Regulations.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    Foreword
    1 Scope
    2 Normative references
    3 Terms and definitions
    4 Sampling and conditioning
    5 Test methods for whole footwear
    6 Test methods for upper, lining and tongue
    7 Test methods for insole and insock
    8 Test methods for outsole
    Annex A (normative) - Procedure for plasticine
            calibration
    Annex B (normative) - Assessment of footwear by
            the laboratory during testing of thermal
            behaviour
    Annex C (informative) - Footwear sizes
    Bibliography
    Annex ZA (informative) - Relationship between this
             European Standard and the Essential
             Requirements of EU Directive 89/686/EEC

    Abstract - (Show below) - (Hide below)

    Describes methods for testing footwear designed as personal protective equipment.

    General Product Information - (Show below) - (Hide below)

    Development Note Supersedes I.S. EN 344 and I.S. EN 344-2 (05/2005) COR 2005 issued on 14-05-2011. (05/2011)
    Document Type Standard
    Publisher National Standards Authority of Ireland
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 13287:2012 Personal protective equipment Footwear Test method for slip resistance
    ISO 3290-1:2014 Rolling bearings Balls Part 1: Steel balls
    ISO 4045:2008 Leather Chemical tests Determination of pH
    ISO 5423:1992 Moulded plastics footwear Lined or unlined polyurethane boots for general industrial use Specification
    ISO 23529:2016 Rubber General procedures for preparing and conditioning test pieces for physical test methods
    ISO 4649:2017 Rubber, vulcanized or thermoplastic Determination of abrasion resistance using a rotating cylindrical drum device
    EN 388 : 1994 PROTECTIVE GLOVES AGAINST MECHANICAL RISKS
    ISO 17249:2013 Safety footwear with resistance to chain saw cutting
    ISO 34-1:2015 Rubber, vulcanized or thermoplastic Determination of tear strength Part 1: Trouser, angle and crescent test pieces
    ISO 3377-2:2016 Leather Physical and mechanical tests Determination of tear load Part 2: Double edge tear
    ISO 20347:2012 Personal protective equipment Occupational footwear
    ISO 4643:1992 Moulded plastics footwear Lined or unlined poly(vinyl chloride) boots for general industrial use Specification
    EN 12568 : 2010 FOOT AND LEG PROTECTORS - REQUIREMENTS AND TEST METHODS FOR TOECAPS AND PENETRATION RESISTANT INSERTS
    ISO 5725-2:1994 Accuracy (trueness and precision) of measurement methods and results Part 2: Basic method for the determination of repeatability and reproducibility of a standard measurement method
    ENV 13005 : DRAFT 1999 GUIDE TO THE EXPRESSION OF UNCERTAINTY IN MEASUREMENT
    ISO 20345:2011 Personal protective equipment Safety footwear
    ISO 17075:2007 Leather Chemical tests Determination of chromium(VI) content
    ISO 3376:2011 Leather Physical and mechanical tests Determination of tensile strength and percentage extension
    ISO 4674-1:2016 Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods
    ISO 868:2003 Plastics and ebonite Determination of indentation hardness by means of a durometer (Shore hardness)
    ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective