IEC 60851-5:2008+AMD1:2011 CSV
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Winding wires - Test methods - Part 5: Electrical properties
Amended by
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
24-09-2019
Language(s)
English - French
Published date
19-08-2011
Publisher
FOREWORD
INTRODUCTION
1 Scope
2 Normative references
3 Test 5: Electrical resistance
4 Test 13: Breakdown voltage
5 Test 14: Continuity of insulation (applicable to
enamelled round and tape wrapped round wire)
6 Test 19: Dielectric dissipation factor (applicable to
enamelled wire and bunched wire)
7 Test 23: Pin hole test
Annex A (informative) - Dissipation factor methods
IEC 60851-5:2008+A1:2011 specifies the following tests:
- Test 5: Electrical resistance;
- Test 13: Breakdown voltage;
- Test 14: Continuity of insulation;
- Test 19: Dielectric dissipation factor.
Significant revisions to the previous edition include the following points:
- In Subclause 5.3, the addition of the use of carbon brush electrodes for the counting discontinuities during the high voltage continuity test, as an alternative to the V-groove pulley electrode; and
- Clarifications in the breakdown voltage test for round wires larger than 2,500 mm and for fibrous covered wires. This consolidated version consists of the fourth edition (2008) and its amendment 1 (2011). Therefore, no need to order amendment in addition to this publication.
| Committee |
TC 55
|
| DevelopmentNote |
Supersedes IEC 60251-4. (03/2001) Stability Date: 2019. (09/2017)
|
| DocumentType |
Standard
|
| Pages |
65
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| OVE/ONORM EN 60851-5 : 2012 | Identical |
| GOST IEC 60851-5 : 2011 ERRATA 2016 | Identical |
| NEN EN IEC 60851-5 : 2008 AMD 1 2011 | Identical |
| I.S. EN 60851-5:2008 | Identical |
| SANS 60851-5 : 2.01ED 2012 | Identical |
| BIS IS 13778-5 : 2012(R2017) | Identical |
| BS EN 60851-5 : 2008 | Identical |
| EN 60851-5:2008/A1:2011 | Identical |
| DIN EN 60851-5:2012-04 | Identical |
| UNE 21180-5:1992 | Identical |
| CEI 55-8/5 V1 : 1993 | Identical |
| GOST R IEC 60851-5 : 2008 ERRATA 2009 | Identical |
| DIN IEC 60851-5:1994-07 | Identical |
| NEN 10851-5 : 1997 AMD 1 1997 | Identical |
| NF EN 60851-5 : 2008 AMD 1 2011 | Identical |
| BS 6811-2.5(1987) : LATEST | Identical |
| UNE-EN 60851-5:2008 | Identical |
| CEI 55-8/5 : 1ED 1997 | Identical |
| PN EN 60851-5 : 2008 AMD 1 2011 | Identical |
| I.S. EN 60851-2:2009 | WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS |
| BS 6811-2.2(1987) : 1987 | WINDING WIRES - METHODS OF TEST - DETERMINATION OF DIMENSIONS |
| 08/30184419 DC : DRAFT JUNE 2008 | BS EN 60851-1 AMD2 - WINDING WIRES - TEST METHODS - PART 1: GENERAL |
| 12/30258455 DC : 0 | FPREN 60065:2011+FPRAA - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
| BS EN 60851-1 : 1998 | WINDING WIRES - TEST METHODS - PART 1: GENERAL |
| CSA C22.2 No. 60065 : 2016 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
| BIS IS 13778-2 : 2013 | WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS |
| CEI EN 60317-25 : 2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 25: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND ALUMINIUM WIRE, CLASS 200 |
| BS 6811-2.6(1987) : 1987 | WINDING WIRES - METHODS OF TEST - THERMAL PROPERTIES |
| BS EN 60065 : 2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014, MODIFIED) |
| CEI EN 60317-0-7 : 2012 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERODEFECT ENAMELLED ROUND COPPER WIRE |
| IEC 60950:1999 | Safety of information technology equipment |
| AAMI ES60601-1 : 2005 : INC : AMD 1 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| UNE-EN 60851-2:2010 | Winding wires - Test methods -- Part 2: Determination of dimensions |
| AAMI ES60601-1 : 2005 : INC : AMD 2 : 2012 : R201200 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| AAMI ES60601-1 : 2005 : R2012 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| CSA C22.2 No. 62368-1 : 2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| UNE-EN 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| BS EN 61558-1 : 2005 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| BS EN 60950:2000 | Safety of information technology equipment |
| IEC 60851-1:1996 | Methods of test for winding wires - Part 1: General |
| EN 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
| EN 61558-1:2005/A1:2009 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| EN 61558-2-16:2009/A1:2013 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1 100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS (IEC 61558-2-16:2009/A1:2013) |
| EN 60359:2002 | Electrical and electronic measurement equipment - Expression of performance |
| EN 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| EN 60950-1:2006/A2:2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005/A2:2013, MODIFIED) |
| EN 60851-2:2009/A1:2015 | WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS |
| CEI EN 62368-1 : 2016 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| PD IEC/TS 62332-3:2016 | Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components Hermetic motor-compressors |
| BS EN 60851-6:1998 | Methods of test for winding wires Thermal properties |
| I.S. EN 60851-1:1998 | WINDING WIRES - TEST METHODS - PART 1: GENERAL |
| BS EN 60359:2002 | Electrical and electronic measurement equipment. Expression of performance |
| 14/30302429 DC : 0 | BS EN 60851-4 - WINDING WIRES - METHODS OF TEST FOR WINDING WIRES - PART 4: CHEMICAL PROPERTIES |
| 11/30193150 DC : 0 | BS EN 60601-1:2006 AMD.1 - MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| CSA E61558.1:2012 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| CAN/CSA-E61558-1:12 (R2017) | Safety of power transformers, power supplies, reactors and similar products - Part 1: General requirements and tests (Adopted IEC 61558- 1:1997 + A1:1998, edition 2.1, 2009-04 with Canadian deviations) | Sécurité des transformateurs, alimentations, bobines d\'inductance et produits analogues - Partie 1: Exigences générales et essais (norme CEI 61558-1:1997 + A1:1998 adoptée, édition 2.1, 2009-04 avec exigences propres au Canada) |
| NF EN 61558-1 : 2006 AMD 1 2009 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| EN IEC 61204-7:2018 | Low-voltage switch mode power supplies - Part 7: Safety requirements |
| IEC 61204-7:2016 EXV | LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS |
| I.S. EN 60851-4:2016 | WINDING WIRES - TEST METHODS - PART 4: CHEMICAL PROPERTIES |
| I.S. EN 61558-2-16:2009 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS |
| NF EN 60950-1 : 2006 AMD 2 2014 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| IEC TS 62332-3:2016 | Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 3: Hermetic motor-compressors |
| AAMI ES60601-1 : 2005 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE (IEC 60601-1:2005, MOD) |
| IEC 60851-2:2009+AMD1:2015 CSV | Winding wires - Test methods - Part 2: Determination of dimensions |
| EN 60065:2014/AC:2017-01 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS (IEC 60065:2014/COR2:2016) |
| BIS IS 13252-1 : 2010 AMD 1 2013 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| BIS IS 13252 : 2003 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - GENERAL REQUIREMENTS |
| DIN EN 60359:2002-09 | ELECTRICAL AND ELECTRONIC MEASUREMENT EQUIPMENT - EXPRESSION OF THE PERFORMANCE |
| 17/30347375 DC : 0 | BS EN 62368-1 ED 3.0 - AUDIO/VIDEO; INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| 12/30239877 DC : 0 | BS EN 60065 ED 8.0 - AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
| BS 6811-2.1(1987) : 1987 | WINDING WIRES - METHODS OF TEST - GENERAL TEST CONDITIONS AND SCHEDULE OF TESTS |
| NF EN 60601-1 : 2007-01 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| IEC 60317-0-7:2017 | Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire |
| 08/30187017 DC : DRAFT JULY 2008 | BS EN 60851-2 - WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS |
| IEC 60317-0-10:2017 | Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire |
| I.S. EN 60317-0-6:2001 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE |
| CEI EN 60317-0-10 : 1ED 2017 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-10: GENERAL REQUIREMENTS - POLYESTER GLASS-FIBRE WOUND FUSED, UNVARNISHED, OR RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE |
| I.S. EN IEC 61204-7:2018 | LOW-VOLTAGE SWITCH MODE POWER SUPPLIES - PART 7: SAFETY REQUIREMENTS |
| I.S. EN 60950-1:2006 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS (IEC 60950-1:2005 (MOD)) |
| PD IEC/TR 60601-4-3:2015 | Medical electrical equipment Guidance and interpretation. Considerations of unaddressed safety aspects in the third edition of IEC 60601-1 and proposals for new requirements |
| IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
| IEC 62368-1:2014 | Audio/video, information and communication technology equipment - Part 1: Safety requirements |
| UNE-EN 60851-4:2017 | Winding wires - Test methods - Part 4: Chemical properties |
| 04/30106146 DC : DRAFT MARCH 2004 | BS EN 60601-1 - MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| CSA C22.2 No. 60950-1 :2007 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 60317-25:2010 | Specifications for particular types of winding wires - Part 25: Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| CSA C22.2 No. 60950-1 : 2007 : INC : AMD 1 : 2011 : R2012 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| UNE-EN 60601-1:2008 | Medical electrical equipment -- Part 1: General requirements for basic safety and essential performance |
| UNE-EN 60950-1:2007 | Information technology equipment - Safety - Part 1: General requirements |
| CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R201200 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 60950-1 : 2007 : R2012 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 60950-1 : 2007 : INC : UPD 1 : 2011 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CSA C22.2 No. 60950-1 : 2007 : INC : AMD 2 : 2014 : R2016 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| 12/30258456 DC : 0 | BS EN 60950-1:2006/FPRAE:2011 - INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| CEI EN 60359 : 2002 | ELECTRICAL AND ELECTRONIC MEASUREMENT EQUIPMENT - EXPRESSION OF PERFORMANCE |
| 12/30239867 DC : 0 | BS EN 62368-1 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| BS EN 60851-4:1998 | Winding Wires. Test methods Chemical properties |
| UNE-EN 60065:2015 | Audio, video and similar electronic apparatus - Safety requirements |
| 12/30258453 DC : 0 | BS EN 62368-1 AMD - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS |
| PD IEC/TS 62332-2:2014 | Electrical insulation systems (EIS). Thermal evaluation of combined liquid and solid components Simplified test |
| I.S. EN 60065:2014 | AUDIO, VIDEO AND SIMILAR ELECTRONIC APPARATUS - SAFETY REQUIREMENTS |
| I.S. EN 60851-6:2012 | WINDING WIRES - TEST METHODS - PART 6: THERMAL PROPERTIES (IEC 60851-6:2012 (EQV)) |
| I.S. EN 62368-1:2014 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED) |
| EN 60851-1:1996/A2:2009 | WINDING WIRES - TEST METHODS - PART 1: GENERAL |
| I.S. EN 60851-3:2009 | WINDING WIRES - TEST METHODS - PART 3: MECHANICAL PROPERTIES (IEC 60851-3:2009 (EQV)) |
| I.S. EN 60317-0-10:2017 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-10: GENERAL REQUIREMENTS - POLYESTER GLASS-FIBRE WOUND FUSED, UNVARNISHED, OR RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE |
| I.S. EN 60601- 1:2006&A1:2013&AC:2014&A12:2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| I.S. EN 60317-0-7:2017 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-7: GENERAL REQUIREMENTS - FULLY INSULATED (FIW) ZERO-DEFECT ENAMELLED ROUND COPPER WIRE |
| IEC 60851-4:2016 | Winding wires - Test methods - Part 4: Chemical properties |
| I.S. EN 61558-1:2006 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| IEC 60950-1:2005+AMD1:2009+AMD2:2013 CSV | Information technology equipment - Safety - Part 1: General requirements |
| IEC 61558-1 REDLINE : 3ED 2017 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND COMBINATIONS THEREOF - PART 1: GENERAL REQUIREMENTS AND TESTS |
| BS EN 60601-1 : 2006 | MEDICAL ELECTRICAL EQUIPMENT PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| BS EN 61558-2-16 : 2009 | SAFETY OF TRANSFORMERS, REACTORS, POWER SUPPLY UNITS AND SIMILAR PRODUCTS FOR SUPPLY VOLTAGES UP TO 1100 V - PART 2-16: PARTICULAR REQUIREMENTS AND TESTS FOR SWITCH MODE POWER SUPPLY UNITS AND TRANSFORMERS FOR SWITCH MODE POWER SUPPLY UNITS |
| IEC 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| IEC 60851-3:2009+AMD1:2013 CSV | Winding wires - Test methods - Part 3: Mechanical properties |
| 15/30328159 DC : 0 | BS EN 61558-1 - SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| IEC 60335-2-34:2012+AMD1:2015+AMD2:2016 CSV | Household and similar electrical appliances - Safety - Part 2-34:Particular requirements for motor-compressors |
| BS EN 60950-1 : 2006 | INFORMATION TECHNOLOGY EQUIPMENT - SAFETY - PART 1: GENERAL REQUIREMENTS |
| 11/30247071 DC : 0 | BS EN 60851-6 - WINDING WIRES - TEST METHODS - PART 6: THERMAL PROPERTIES |
| BS 6811-2.4(1987) : 1987 AMD 8387 | WINDING WIRES - METHODS OF TEST - CHEMICAL PROPERTIES |
| BS EN 60317-0-7:2017 | Specifications for particular types of winding wires General requirements. Fully insulated (FIW) zero-defect enamelled round copper wire |
| BS EN 60317-0-10:2017 | Specifications for particular types of winding wires General requirements. Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire |
| CSA E61558.1 : 2012 : INC : UPD 1 : 2014 | SAFETY OF POWER TRANSFORMERS, POWER SUPPLIES, REACTORS AND SIMILAR PRODUCTS - PART 1: GENERAL REQUIREMENTS AND TESTS |
| IEC TS 62332-2:2014 | Electrical insulation systems (EIS) - Thermal evaluation of combined liquid and solid components - Part 2: Simplified test |
| CAN/CSA-C22.2 NO. 60335-2-34:17 | Household and similar electrical appliances — Safety — Part 2-34: Particular requirements for motor-compressors (Binational standard with UL 60335-2-34) |
| UNE-EN 60317-0-10:2017 | Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire |
| I.S. EN 60359:2002 | ELECTRICAL AND ELECTRONIC MEASUREMENT EQUIPMENT - EXPRESSION OF PERFORMANCE |
| EN 60317-0-7:2017 | Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire |
| I.S. EN 60317-25:2010 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 25: POLYESTER OR POLYESTERIMIDE OVERCOATED WITH POLYAMIDE-IMIDE ENAMELLED ROUND ALUMINIUM WIRE, CLASS 200 |
| BS EN 60317-25:2010 | Specifications for particular types of winding wires Polyester or polyesterimide overcoated with polyamide-imide enamelled round aluminium wire, class 200 |
| CSA C22.2 No. 60601.1 : 2014 | MEDICAL ELECTRICAL EQUIPMENT - PART 1: GENERAL REQUIREMENTS FOR BASIC SAFETY AND ESSENTIAL PERFORMANCE |
| EN 62368-1:2014/AC:2017-03 | AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - PART 1: SAFETY REQUIREMENTS (IEC 62368-1:2014, MODIFIED) |
| UNE-EN 60317-0-7:2012 | Specifications for particular types of winding wires - Part 0-7: General requirements - Fully insulated (FIW) zero-defect enamelled round copper wire with nominal conductor diameter of 0,040 mm to 1,600 mm |
| BS EN 60851-3 : 2009 | WINDING WIRES - TEST METHODS - PART 3: MECHANICAL PROPERTIES |
| BS EN 60851-2 : 2009 | WINDING WIRES - TEST METHODS - PART 2: DETERMINATION OF DIMENSIONS |
| 07/30091745 DC : 0 | BS IEC 62368 - AUDIO/VIDEO, INFORMATION AND COMMUNICATION TECHNOLOGY EQUIPMENT - SAFETY - REQUIREMENTS |
| BS EN IEC 61204-7:2018 | Low-voltage switch mode power supplies Safety requirements |
| IEC 61558-2-16:2009+AMD1:2013 CSV | Safety of transformers, reactors, power supply units and similar products for supply voltages up to 1 100 V - Part 2-16: Particularrequirements and tests for switch mode power supply units andtransformers for switch mode power supply units |
| IEC 60601-1:2005+AMD1:2012 CSV | Medical electrical equipment - Part 1: General requirements for basic safety and essential performance |
| NF EN 60317-0-6 : 2002 AMD 1 2007 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBER WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE |
| EN 60317-0-10:2017 | Specifications for particular types of winding wires - Part 0-10: General requirements - Polyester glass-fibre wound fused, unvarnished, or resin or varnish impregnated, bare or enamelled round copper wire |
| EN 60950:2000/corrigendum:2002 | SAFETY OF INFORMATION TECHNOLOGY EQUIPMENT |
| EN 60851-6:2012 | Winding wires - Test methods - Part 6: Thermal properties |
| OVE/ONORM EN 60317-0-6 : 2007 | SPECIFICATIONS FOR PARTICULAR TYPES OF WINDING WIRES - PART 0-6: GENERAL REQUIREMENTS - GLASS-FIBRE WOUND RESIN OR VARNISH IMPREGNATED, BARE OR ENAMELLED ROUND COPPER WIRE |
| UNE-EN 60851-1:1997 | WINDING WIRES. TEST METHODS. PART 1: GENERAL. |
| CEI EN IEC 60317-89:2024 | Specifications for particular types of winding wires - Part 89: Polyesterimide enamelled round aluminum wire, class 200 |
| IEC 60851-1:1996 | Methods of test for winding wires - Part 1: General |
£253.29
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English - French
PDF - English - French
PDF 3 Users - English - French
PDF 5 Users - English - French
PDF 9 Users - English - French
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.