IEC 60974-7:2013
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Arc welding equipment - Part 7: Torches
Available format(s)
Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users
Superseded date
31-12-2021
Language(s)
English - French
Published date
24-01-2013
Publisher
FOREWORD
1 Scope
2 Normative references
3 Terms and definitions
4 Environmental conditions
5 Classification
6 Test conditions
7 Protection against electric shock
8 Thermal rating
9 Pressure of the liquid cooling system
10 Resistance to hot objects
11 Mechanical provisions
12 Marking
13 Instructions for use
Annex A (informative) - Additional terminology
Annex B (normative) - Position of the welding torches
for the heating test
Annex C (informative) - Cooled copper block
Annex D (informative) - Copper block with a hole
Annex E (informative) - Copper bars with a slot
Bibliography
IEC 60974-7:2013 specifies safety and construction requirements for torches for arc welding and allied processes. This part of IEC 60974 is applicable to manual, mechanically guided, air-cooled, liquid-cooled, motorized, spool-on and fume extraction torches. In this part of IEC 60974, a torch consists of the torch body, the cable-hose assembly and other components. This part of IEC 60974 is also applicable to a cable-hose assembly connected between a power source and ancillary equipment. This part of IEC 60974 is not applicable to electrode holders for manual metal arc welding or air-arc cutting/gouging. This third edition cancels and replaces the second edition published in 2007 and constitutes a technical revision. The significant changes with respect to the previous edition are listed below:
- new requirement for degree of protection of torch coupling device (see Table 1);
- scope is extended to cable-hose assembly connected between a power source and ancillary equipment (see Clause 1);
- torch parts, as recommended by the manufacturer, are included in the safe plasma cutting system design (see 7.4.2);
- new flammability requirement for handle material (see 11.3).
This publication is to be read in conjunction with IEC 60974-1:2012.
| Committee |
TC 26
|
| DevelopmentNote |
To be used in conjunction with IEC 60974-1. (07/2005) Stability Date: 2018. (11/2017)
|
| DocumentType |
Standard
|
| Pages |
59
|
| PublisherName |
International Electrotechnical Committee
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| Standards | Relationship |
| SN EN 60974-7:2013 | Identical |
| GOST IEC 60974-7 : 2015 | Identical |
| NEN EN IEC 60974-7 : 2013 | Identical |
| PN EN 60974-7 : 2013 | Identical |
| SANS 60974-7 : 3ED 2014 | Identical |
| SAC GB 15579-7 : 2013 | Identical |
| VDE 0544-7 : 2013 | Identical |
| DIN EN 60974-7 : 2013 | Identical |
| UNE-EN 60974-7:2006 | Identical |
| BS EN 60974-7:2013 | Identical |
| CEI EN 60974-7 : 2014 | Identical |
| EN 60974-7:2013 | Identical |
| NF EN 60974-7 : 2013 | Identical |
| SANS 60974-:2014(R2020) | Identical |
| NEMA IEC 60974-7 : 2009 | Identical |
| UNE-EN 60974-7:2013 | Identical |
| SN EN 60974-7 : 2005 | Identical |
| PD CEN/TR 15339-3:2014 | Thermal spraying. Safety requirements for thermal spraying equipment Torches for thermal spraying and their connection and supply units |
| 04/19971117 DC : DRAFT AUG 2004 | BS EN ISO 15011-4 - HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES GENERATED BY ARC WELDING - PART 4: FUME DATA SHEETS |
| 07/30164535 DC : 0 | BS EN 60974-8 - ARC WELDING EQUIPMENT - PART 8: GAS CONSOLES FOR WELDING AND PLASMA CUTTING SYSTEMS |
| 04/30122740 DC : DRAFT SEP 2004 | IEC 60974-4 - ARC WELDING EQUIPMENT - PART 4: SAFETY, MAINTENANCE AND INSPECTION OF ARC WELDING EQUIPMENT IN USE |
| CSA E60974.5 : 2009 : R2013 | ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS |
| UNI EN ISO 15011-4 : 2009 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 4: FUME DATA SHEETS |
| 00/705404 DC : DRAFT FEB 2000 | |
| UNE-EN 60974-6:2011 | Arc welding equipment - Part 6: Limited duty equipment |
| 17/30346770 DC : 0 | BS EN 60974-9 - ARC WELDING EQUIPMENT - PART 9: INSTALLATION AND USE |
| EN 60974-8:2009 | Arc welding equipment - Part 8: Gas consoles for welding and plasma cutting systems |
| EN 60974-5:2013 | ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS (IEC 60974-5:2013) |
| BS EN 60974-8:2009 | Arc welding equipment Gas consoles for welding and plasma cutting systems |
| 06/30148959 DC : DRAFT APR 2006 | IEC 60974-2 ED.2 - ARC WELDING EQUIPMENT - PART 2: LIQUID COOLING SYSTEMS |
| I.S. EN 60974-2:2013 | ARC WELDING EQUIPMENT - PART 2: LIQUID COOLING SYSTEMS (IEC 60974-2:2013 (EQV)) |
| 06/30148965 DC : DRAFT APR 2006 | IEC 60974-5 - ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS |
| DD IEC TS 60680 : DRAFT APR 2008 | TEST METHODS OF PLASMA EQUIPMENT FOR ELECTROHEAT AND ELECTROCHEMICAL APPLICATIONS |
| IEC 60974-8:2009 | Arc welding equipment - Part 8: Gas consoles for welding and plasma cutting systems |
| BS EN 60974-3:2014 | Arc welding equipment Arc striking and stabilizing devices |
| DD IEC/TS 60519-5:2008 | Safety in electroheat installations Specifications for safety in plasma installations |
| 06/30137125 DC : DRAFT SEP 2006 | ISO 15011-3 - HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 3: DETERMINATION OF OZONE EMISSION RATE |
| IEC 60974-6:2015 | Arc welding equipment - Part 6: Limited duty equipment |
| CEI EN 60974-8 : 2011 | ARC WELDING EQUIPMENT - PART 8: GAS CONSOLES FOR WELDING AND PLASMA CUTTING SYSTEMS |
| CAN/CSA-E60974-5-09 (R2018) | Arc welding equipment - Part 5: Wire feeders (Adopted CEI/IEC 60974-5:2009, second edition, 2007-11, with Canadian deviations) | Matériel de soudage à l\'arc - Partie 5: Dévidoirs (norme CEI/IEC 60974-5:2009 adoptée, deuxième édition, 2007-11, avec exigences propres au Canada) |
| I.S. EN 60974-6:2016 | ARC WELDING EQUIPMENT - PART 6: LIMITED DUTY EQUIPMENT |
| I.S. EN 60974-9:2010 | ARC WELDING EQUIPMENT - PART 9: INSTALLATION AND USE |
| ISO 15011-4:2017 | Health and safety in welding and allied processes — Laboratory method for sampling fume and gases — Part 4: Fume data sheets |
| DIN EN ISO 15011-4:2009-07 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 4: FUME DATA SHEETS |
| I.S. EN 60974-3:2014 | ARC WELDING EQUIPMENT - PART 3: ARC STRIKING AND STABILIZING DEVICES |
| I.S. EN 60974-8:2009 | ARC WELDING EQUIPMENT - PART 8: GAS CONSOLES FOR WELDING AND PLASMA CUTTING SYSTEMS |
| I.S. EN ISO 15011-3:2009 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 3: DETERMINATION OF OZONE EMISSION RATE DURING ARC WELDING |
| NEMA IEC 60974-3 : 2009 | AMERICAN NATIONAL STANDARD FOR ARC WELDING EQUIPMENT - PART 3: ARC STRIKING AND STABILIZING DEVICES |
| NEMA IEC 60974-5 : 2009 | ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS |
| NEMA IEC 60974-1 : 2008 | ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES |
| NEMA IEC 60974-8 : 2008 | ARC WELDING EQUIPMENT - PART 8: GAS CONSOLES FOR WELDING AND PLASMA CUTTING SYSTEMS |
| NEMA IEC 60974-2 : 2009 | AMERICAN NATIONAL STANDARD FOR ARC WELDING EQUIPMENT - PART 2: LIQUID COOLING SYSTEMS |
| 05/30141013 DC : DRAFT OCT 2005 | IEC 60974-3 ED 2 - ARC WELDING EQUIPMENT - PART 3: ARC STRIKING AND STABILIZING DEVICES |
| 04/30095682 DC : DRAFT APR 2004 | IEC 60974-1 ED.3 - ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES |
| I.S. EN 60974-1:2012 | ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES (IEC 60974-1:2012 (EQV)) |
| BS EN 60974-6:2016 | Arc welding equipment Limited duty equipment |
| 11/30247475 DC : 0 | BS EN 60974-5 - ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS |
| 14/30299454 DC : 0 | BS EN 60974-6 - ARC WELDING EQUIPMENT - PART 6: LIMITED DUTY EQUIPMENT |
| BS EN 60974-5:2013 | Arc welding equipment Wire feeders |
| BS EN 60974-1:2012 | Arc welding equipment Welding power sources |
| 08/30195564 DC : 0 | BS EN 60974-1 - ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES |
| AWS D16.2M/16.2 : 2007 | GUIDE FOR COMPONENTS OF ROBOTIC AND AUTOMATIC ARC WELDING INSTALLATIONS |
| I.S. EN ISO 15011-4:2018 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 4: FUME DATA SHEETS (ISO 15011-4:2017) |
| IEC 60974-1:2017 | Arc welding equipment - Part 1: Welding power sources |
| DIN EN ISO 15011-3:2010-03 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 3: Determination of ozone emission rate during arc welding (ISO 15011-3:2009) |
| IEC 60974-5:2013 | Arc welding equipment - Part 5: Wire feeders |
| UNI EN ISO 15011-2 : 2010 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 2: DETERMINATION OF THE EMISSION RATES OF CARBON MONOXIDE (CO), CARBON DIOXIDE (CO[2]), NITROGEN MONOXIDE (NO) AND NITROGEN DIOXIDE (NO[2]) DURING ARC WELDING, CUTTING AND GOUGING |
| EEMUA 143 : 1985 | RECOMMENDATIONS FOR TUBE END WELDING |
| CEI EN 60974-2 : 2014 | ARC WELDING EQUIPMENT - PART 2: LIQUID COOLING SYSTEMS |
| 12/30262932 DC : 0 | BS EN 15339-3 - THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 3: TORCHES FOR THERMAL SPRAYING AND THEIR CONNECTION AND SUPPLY UNITS |
| UNI EN ISO 15011-3 : 2010 | HEALTH AND SAFETY IN WELDING AND ALLIED PROCESSES - LABORATORY METHOD FOR SAMPLING FUME AND GASES - PART 3: DETERMINATION OF OZONE EMISSION RATE DURING ARC WELDING |
| CEN/TR 15339-3:2014 | Thermal spraying - Safety requirements for thermal spraying equipment - Part 3: Torches for thermal spraying and their connection and supply units |
| BS EN 60974-2:2013 | Arc welding equipment Liquid cooling systems |
| 13/30288591 DC : 0 | BS EN 60974-1 - ARC WEDLING EQUIPMENT - PART 1: WELDING POWER SOURCE |
| 11/30255758 DC : 0 | BS EN 60974-3 - ARC WELDING EQUIPMENT - PART 3: ARC STRIKING AND STABILIZING DEVICES |
| 11/30240803 DC : DRAFT JAN 2011 | BS EN 60974-2 - ARC WELDING EQUIPMENT - PART 2: LIQUID COOLING SYSTEMS |
| 07/30164743 DC : 0 | BS EN 60974-6 - ARC WELDING EQUIPMENT - PART 6: LIMITED DUTY MANUAL METAL ARC WELDING POWER SOURCES |
| CEI EN 60974-5 : 2014 | ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS |
| I.S. EN 60974-5:2013 | ARC WELDING EQUIPMENT - PART 5: WIRE FEEDERS (IEC 60974-5:2013 (EQV)) |
| UNE-EN 60974-3:2014 | Arc welding equipment - Part 3: Arc striking and stabilizing devices |
| S.R. CEN/TR 15339-3:2014 | THERMAL SPRAYING - SAFETY REQUIREMENTS FOR THERMAL SPRAYING EQUIPMENT - PART 3: TORCHES FOR THERMAL SPRAYING AND THEIR CONNECTION AND SUPPLY UNITS |
| IEC TS 60519-5:2008 | Safety in electroheat installations - Part 5: Specifications for safety in plasma installations |
| IEC TS 60680:2008 | Test methods of plasma equipment for electroheat and electrochemical applications |
| DIN EN ISO 15011-2:2010-03 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO<(Index)2>), nitrogen monoxide (NO) and nitrogen dioxide (NO<(Index)2>) during arc welding, cutting and gouging (ISO 15011-2:2009) |
| BS EN ISO 15011-2:2009 | Health and safety in welding and allied processes. Laboratory method for sampling fume and gases Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging |
| IEC 60974-2:2013 | Arc welding equipment - Part 2: Liquid cooling systems |
| ISO 15011-2:2009 | Health and safety in welding and allied processes Laboratory method for sampling fume and gases Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging |
| ISO 15011-3:2009 | Health and safety in welding and allied processes Laboratory method for sampling fume and gases Part 3: Determination of ozone emission rate during arc welding |
| IEC 60974-3:2013 | Arc welding equipment - Part 3: Arc striking and stabilizing devices |
| BS EN ISO 15011-3:2009 | Health and safety in welding and allied processes. Laboratory method for sampling fume and gases Determination of ozone emission rate during arc welding |
| EN ISO 15011-3:2009 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 3: Determination of ozone emission rate during arc welding (ISO 15011-3:2009) |
| EN ISO 15011-2:2009 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 2: Determination of the emission rates of carbon monoxide (CO), carbon dioxide (CO2), nitrogen monoxide (NO) and nitrogen dioxide (NO2) during arc welding, cutting and gouging (ISO 15011-2:2009) |
| CEI EN 60974-1 : 2013 | ARC WELDING EQUIPMENT - PART 1: WELDING POWER SOURCES |
| EN ISO 15011-4:2018 | Health and safety in welding and allied processes - Laboratory method for sampling fume and gases - Part 4: Fume data sheets (ISO 15011-4:2017) |
| UNE-EN 60974-1:2013 | Arc welding equipment - Part 1: Welding power sources |
| BS EN 60974-9:2010 | Arc welding equipment Installation and use |
| 07/30173638 DC : 0 | BS EN 60974-9 - ARC WELDING EQUIPMENT - PART 9: INSTALLATION AND USE |
| EN 60974-9:2010 | Arc welding equipment - Part 9: Installation and use |
| EN 60974-6:2016 | Arc welding equipment - Part 6: Limited duty equipment |
| EN 60974-1:2012 | Arc welding equipment - Part 1: Welding power sources |
| EN 60974-2:2013 | Arc welding equipment - Part 2: Liquid cooling systems |
| EN 60974-3:2014 | Arc welding equipment - Part 3: Arc striking and stabilizing devices |
| UNE-EN 60974-5:2014 | Arc welding equipment - Part 5: Wire feeders |
| IEC 60974-2:2013 | Arc welding equipment - Part 2: Liquid cooling systems |
| IEC 60974-1:2017 | Arc welding equipment - Part 1: Welding power sources |
| IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
| IEC 60695-11-10:2013 | Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical flame test methods |
| IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
£178.24
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English - French
PDF - English - French
PDF 3 Users - English - French
PDF 5 Users - English - French
PDF 9 Users - English - French
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.