ISO 10350-2:2011

Withdrawn

View Superseded by

Plastics Acquisition and presentation of comparable single-point data Part 2: Long-fibre-reinforced plastics

Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Withdrawn date

23-07-2020

Language(s)

French, English

Published date

17-02-2011

Publisher

International Organization for Standardization

ISO 10350 identifies specific test procedures for the acquisition and presentation of comparable data for certain basic properties of plastics. In general, each property is specified by a single experimental value, although in certain cases properties are represented by two values obtained under different test conditions or along different directions in the material. The properties included are those presented conventionally in manufacturers' data sheets. ISO 10350-2:2011 applies to reinforced thermoplastic and thermosetting materials where the reinforcement fibres are either discontinuous with a fibre length prior to processing greater than 7,5 mm or continuous (e.g. fabric, continuous-strand mat or unidirectional). ISO 10350-1 deals specifically with unreinforced and filled plastics, including those using fibres less than 7,5 mm in length.

DevelopmentNote	Supersedes ISO/DIS 10350-2. (02/2011)
DocumentType	Standard
Pages	10
ProductNote	THIS STANDARD ALSO REFERS TO ISO 1183 (all parts),ISO 1268 (all parts)
PublisherName	International Organization for Standardization
Status	Withdrawn
SupersededBy	ISO 10350-2:2020
Supersedes	ISO 10350-2:2001

Standards	Relationship
ONORM EN ISO 10350-2 : 2011	Identical
NF EN ISO 10350-2 : 2011	Identical
NBN EN ISO 10350-2 : 2011	Identical
NEN EN ISO 10350-2 : 2011	Identical
NS EN ISO 10350-2 : 2011	Identical
I.S. EN ISO 10350-2:2011	Identical
PN EN ISO 10350-2 : 2011	Identical
SN EN ISO 10350-2 : 2011	Identical
UNI EN ISO 10350-2 : 2011	Identical
UNE-EN ISO 10350-2:2011	Identical
BS EN ISO 10350-2:2011	Identical
EN ISO 10350-2:2011	Identical
DIN EN ISO 10350-2:2011-06	Identical
SAC GB/T 19467-2 : 2004	Identical

ISO 178:2010	Plastics Determination of flexural properties
BS ISO 17422:2002	Plastics. Environmental aspects. General guidelines for their inclusion in standards
BS ISO 20753 : 2008	PLASTICS - TEST SPECIMENS
BS ISO 1268-10:2005	Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre compounds. General principles and moulding of multipurpose test specimens
DIN EN ISO 20753 E : 2014	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
DIN EN ISO 20753:2014-07	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
DIN EN 14598-3:2005-07	Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
DIN EN 14598-2:2005-07	Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
DIN EN ISO 11403-3 E : 2002	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)
BS EN ISO 11403-3:2014	Plastics. Acquisition and presentation of comparable multipoint data Environmental influences on properties
I.S. EN ISO 11403-2:2012	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012)
DIN EN ISO 178:2013-09	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013)
16/30310691 DC : 0	BS EN ISO 294-1 - PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS
I.S. EN ISO 178:2010	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010)
DIN EN ISO 178 E : 2013	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010 + AMD.1:2013)
05/30132990 DC : DRAFT APR 2005	ISO 20753 - PLASTICS - TEST SPECIMENS
EN ISO 11403-3:2014	Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)
I.S. EN ISO 20753:2014	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
UNE-ISO 1268-11:2012	Fibre-reinforced plastics. Methods of producing test plates. Part 11: Injection moulding of BMC and other long-fibre moulding compounds. Small plates
ISO 1268-11:2005	Fibre-reinforced plastics — Methods of producing test plates — Part 11: Injection moulding of BMC and other long-fibre moulding compounds — Small plates
BS EN 14598-2:2005	Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements
I.S. EN ISO 294-1:2017	PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017)
I.S. EN ISO 11403-3:2014	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)
17/30333280 DC : 0	BS ISO 17422 - PLASTICS - ENVIRONMENTAL ASPECTS - GENERAL GUIDELINES FOR THEIR INCLUSION IN STANDARDS
BS EN 62631-3-2:2016	Dielectric and resistive properties of solid insulating materials Determination of resistive properties (DC Methods). Surface resistance and surface resistivity
BS ISO 1268-11:2005	Fibre-reinforced plastics. Methods of producing test plates Injection moulding of BMC and other long-fibre moulding compounds. Small plates
I.S. EN 62631-3-2:2016	DIELECTRIC AND RESISTIVE PROPERTIES OF SOLID INSULATING MATERIALS - PART 3-2: DETERMINATION OF RESISTIVE PROPERTIES (DC METHODS) - SURFACE RESISTANCE AND SURFACE RESISTIVITY
ONORM EN ISO 20753 : 2014	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
ISO 20753:2008	Plastics Test specimens
UNI EN ISO 178 : 2013	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES
IEC 62631-3-2:2015	Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC methods) - Surface resistance and surface resistivity
BS EN ISO 20753:2014	Plastics. Test specimens
DIN EN ISO 11403-3:2014-09	Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)
UNE-EN ISO 294-1:2017	Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)
UNE-EN ISO 11403-2:2012	Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
BS EN ISO 11403-2:2012	Plastics. Acquisition and presentation of comparable multipoint data Thermal and processing properties
UNI EN ISO 11403-2 : 2012	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES
I.S. EN ISO 10350-1:2017	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 1: MOULDING MATERIALS (ISO 10350-1:2017)
17/30335677 DC : 0	BS EN ISO 178 - PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES
UNI EN ISO 20753 : 2014	PLASTICS - TEST SPECIMENS
EN ISO 20753:2014	PLASTICS - TEST SPECIMENS (ISO 20753:2008)
ISO 17422:2002	Plastics Environmental aspects General guidelines for their inclusion in standards
ISO 1268-10:2005	Fibre-reinforced plastics — Methods of producing test plates — Part 10: Injection moulding of BMC and other long-fibre moulding compounds — General principles and moulding of multipurpose test specimens
UNI EN ISO 11403-3 : 2014	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES
DIN EN ISO 294-1:2017-09	PLASTICS - INJECTION MOULDING OF TEST SPECIMENS OF THERMOPLASTIC MATERIALS - PART 1: GENERAL PRINCIPLES, AND MOULDING OF MULTIPURPOSE AND BAR TEST SPECIMENS (ISO 294-1:2017)
ISO 294-1:2017	Plastics — Injection moulding of test specimens of thermoplastic materials — Part 1: General principles, and moulding of multipurpose and bar test specimens
ISO 11403-2:2012	Plastics — Acquisition and presentation of comparable multipoint data — Part 2: Thermal and processing properties
BS EN 14598-3:2005	Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements
BS EN ISO 294-1:2017	Plastics. Injection moulding of test specimens of thermoplastic materials General principles, and moulding of multipurpose and bar test specimens
UNE-EN ISO 11403-3:2014	Plastics - Acquisition and presentation of comparable multipoint data - Part 3: Environmental influences on properties (ISO 11403-3:2014)
EN ISO 11403-2:2012	Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
EN ISO 294-1:2017	Plastics - Injection moulding of test specimens of thermoplastic materials - Part 1: General principles, and moulding of multipurpose and bar test specimens (ISO 294-1:2017)
EN 14598-2:2005/AC:2006	REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
EN ISO 10350-1:2017	Plastics - Acquisition and presentation of comparable single-point data - Part 1: Moulding materials (ISO 10350-1:2017)
EN 14598-3:2005	Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
BS EN ISO 178 : 2010	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES
UNE-ISO 1268-10:2012	Fibre-reinforced plastics. Methods of producing test plates. Part 10: Injection moulding of BMC and other long-fibre moulding compounds. General principles and moulding of multipurpose test specimens
BS EN ISO 10350-1:2017	Plastics. Acquisition and presentation of comparable single-point data Moulding materials
EN ISO 178:2010/A1:2013	PLASTICS - DETERMINATION OF FLEXURAL PROPERTIES (ISO 178:2010/AMD 1:2013)
UNE-EN ISO 20753:2015	Plastics - Test specimens (ISO 20753:2008)
DIN EN ISO 11403-2 E : 2013	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 2: THERMAL AND PROCESSING PROPERTIES (ISO 11403-2:2012)
EN 62631-3-2:2016	Dielectric and resistive properties of solid insulating materials - Part 3-2: Determination of resistive properties (DC Methods) - Surface resistance and surface resistivity
DIN EN ISO 11403-2:2013-01	Plastics - Acquisition and presentation of comparable multipoint data - Part 2: Thermal and processing properties (ISO 11403-2:2012)
DIN EN ISO 11403-3:2002-02	PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE MULTIPOINT DATA - PART 3: ENVIRONMENTAL INFLUENCES ON PROPERTIES (ISO 11403-3:2014)