• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ISO 1172:1996

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Textile-glass-reinforced plastics — Prepregs, moulding compounds and laminates — Determination of the textile-glass and mineral-filler content — Calcination methods
Available format(s)

Hardcopy , PDF , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

31-08-2023

Language(s)

English, French

Published date

26-12-1996

Gives two calcination methods for the determination of the textile-glass and mineral-filler content of glass-reinforced plastics. Method A is used for the determination of the textile-glass content when no mineral fillers are present; method B is used when both components are present. Replaces the first edition.

Committee
ISO/TC 61/SC 13
DocumentType
Standard
Pages
8
PublisherName
International Organization for Standardization
Status
Superseded
SupersededBy
Supersedes

I.S. EN 13121-3:2016 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
BS ISO 1268-2:2001 Fibre-reinforced plastics. Methods of producing test plates Contact and spray-up moulding
BS ISO 8605:2001 Textile-glass-reinforced plastics. Sheet moulding compound (SMC). Basis for specification
BS ISO 1268-4 : 2005 FIBRE-REINFORCED PLASTICS - METHODS OF PRODUCING TEST PLATES - PART 4: MOULDING OF PREPREGS
BS ISO 1268-7:2001 Fibre-reinforced plastics. Methods of producing test plates Resin transfer moulding
97/713388 DC : DRAFT AUG 1997 PREN 2719 - AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION
ISO 1268-7:2001 Fibre-reinforced plastics Methods of producing test plates Part 7: Resin transfer moulding
PREN 2719 : 200P1 AEROSPACE SERIES - POLYCARBONATE SHEET - TECHNICAL SPECIFICATION
ISO 9163:2005 Textile glass — Rovings — Manufacture of test specimens and determination of tensile strength of impregnated rovings
DIN EN 13121-2:2004-01 GRP tanks and vessels for use above ground - Part 2: Composite materials; Chemical resistance
DIN EN 14598-3:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
DIN EN 14598-2:2005-07 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 2: Methods of test and general requirements
BS EN 13706-3:2002 Reinforced plastics composites. Specifications for pultruded profiles Specific requirements
BS EN 13677-2:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Methods of test and general requirements
EN 12080:2017 Railway applications - Axleboxes - Rolling bearings
DIN EN ISO 9163:2005-07 Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:2005); German version EN ISO 9163:2005
EN 1013:2012+A1:2014 LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
NF EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
EN 13121-3:2016 GRP tanks and vessels for use above ground - Part 3: Design and workmanship
I.S. EN ISO 14692-2:2017 PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 2: QUALIFICATION AND MANUFACTURE (ISO 14692-2:2017)
07/30165210 DC : 0 BS EN ISO 10350-2 - PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
BS ISO 4901:2011 Reinforced plastics based on unsaturated-polyester resins. Determination of the residual styrene monomer content, as well as the content of other volatile aromatic hydrocarbons, by gas chromatography
10/30192393 DC : 0 BS ISO 4901 - REINFORCED PLASTICS BASED ON UNSATURATED POLYESTER RESINS - DETERMINATION OF RESIDUAL STYRENE MONOMER CONTENT AS WELL AS THE CONTENT OF OTHER VOLATILE AROMATIC HYDROCARBONS, BY GAS CHROMATOGRAPHY
15/30304304 DC : 0 BS EN 12080 - RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS
BS 2782-10:Method 1008B:1996 Methods of testing plastics. Glass reinforced plastics Determination of flexural strength on rods made of roving-reinforced resin
BS 2782-10:Method 1008C:1996 Methods of testing plastics. Glass reinforced plastics Determination of compressive strength on rods made from roving-reinforced resins
EN 4691-1:2017 Aerospace series - Tie rod with integrated bolts - Part 1: Technical specification
PREN 12080 : DRAFT 2015 RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS
ASTM D 3754 : 2014 : REDLINE Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Sewer and Industrial Pressure Pipe
I.S. EN ISO 12736:2014 PETROLEUM AND NATURAL GAS INDUSTRIES - WET THERMAL INSULATION COATINGS FOR PIPELINES, FLOW LINES, EQUIPMENT AND SUBSEA STRUCTURES (ISO 12736:2014)
ISO 8606:1990 Plastics — Prepregs — Bulk moulding compound (BMC) and dough moulding compound (DMC) — Basis for a specification
DIN EN ISO 10350-2:2011-06 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
DIN EN 12080:2015-06 (Draft) RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS
BS EN 12080:2017 Railway applications. Axleboxes. Rolling bearings
BS EN 14598-2:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Methods of test and general requirements
I.S. EN 12080:2017 RAILWAY APPLICATIONS - AXLEBOXES - ROLLING BEARINGS
DIN EN 13121-3:2016-10 GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
DIN EN 12080:2017-11 Railway applications - Axleboxes - Rolling bearings
BS 4549-1:1997 Guide to quality control requirements for reinforced plastics mouldings Guide to the preparation of a scheme to control the quality of glass reinforced polyester mouldings
BS 3749:1991 Specification for E glass fibre woven roving fabrics for the reinforcement of polyester and epoxy resins systems
NBR 15708-5 : 2011 PETROLEUM AND NATURAL GAS INDUSTRIES - PULTRUDED SHAPES - PART 5: STRUCTURAL SHAPES
ISO 1268-9:2003 Fibre-reinforced plastics — Methods of producing test plates — Part 9: Moulding of GMT/STC
16/30292780 DC : 0 BS ISO 7510 - PLASTICS PIPING SYSTEMS - GLASS-REINFORCED PLASTICS (GRP) COMPONENTS - DETERMINATION OF THE AMOUNTS OF CONSTITUENTS
DIN EN 1013:2015-03 LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
BS ISO 1268-9:2003 Fibre-reinforced plastics. Methods of producing test plates Moulding of GMT/STC
BS 2782-10:Method 1008D:1996 Methods of testing plastics. Glass reinforced plastics Determination of apparent interlaminar shear strength on rods made of roving-reinforced resins
ESPECIFICACION UNE 0059:2017 Fiberglass reinforced polyester poles for overhead power distribution lines and telephony lines
12/30258334 DC : 0 BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTIC SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
BS ISO 1268-6:2002 Fibre-reinforced plastics. Methods of producing test plates Pultrusion moulding
04/30112206 DC : DRAFT APR 2004 BS ISO 22314 - PLASTICS - GLASS-FIBRE-REINFORCED PRODUCTS - DETERMINATION OF FIBRE LENGTH
UNE-ISO 1268-6:2012 Fibre-reinforced plastics -- Methods of producing test plates -- Part 6: Pultrusion moulding
BS ISO 22314:2006 Plastics. Glass-fibre-reinforced products. Determination of fibre length
UNE-ISO 4901:2014 Reinforced plastics based on unsaturated-polyester resins. Determination of the residual styrene monomer content, as well as the content of other volatile aromatic hydrocarbons, by gas chromatography
BS EN 1013 : 2012 LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
I.S. EN 4691-1:2017 AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - PART 1: TECHNICAL SPECIFICATION
NF ISO 1268-9 : 2003 FIBRE-REINFORCED PLASTICS - METHODS OF PRODUCING TEST PLATES - PART 9: MOULDING OF GMT/STC
BS EN 13121-3:2016 GRP tanks and vessels for use above ground Design and workmanship
ISO 1268-6:2002 Fibre-reinforced plastics — Methods of producing test plates — Part 6: Pultrusion moulding
UNE-EN 13121-3:2017 GRP tanks and vessels for use above ground - Part 3: Design and workmanship
ASTM D 3517 : 2014 : REDLINE Standard Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe
ISO 8605:2001 Textile-glass-reinforced plastics — Sheet moulding compound (SMC) — Basis for a specification
ISO 14692-2:2017 Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 2: Qualification and manufacture
DIN EN ISO 9163 E : 2005 TEXTILE GLASS - ROVINGS - MANUFACTURE OF TEST SPECIMENS AND DETERMINATION OF TENSILE STRENGTH OF IMPREGNATED ROVINGS
BS EN 13706-2:2002 Reinforced plastics composites. Specifications for pultruded profiles Method of test and general requirements
12/30260914 DC : 0 BS EN 4718 - AEROSPACE SERIES - POLYETHERKETONE WITH 55% CONTINUOUS GLASS FIBRE BY VOLUME (PEEK-GF55)
BS EN ISO 10350-2:2011 Plastics. Acquisition and presentation of comparable single-point data Long-fibre-reinforced plastics
EN ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
UNI EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
ONORM EN ISO 10350-2 : 2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
I.S. EN ISO 10350-2:2011 PLASTICS - ACQUISITION AND PRESENTATION OF COMPARABLE SINGLE-POINT DATA - PART 2: LONG-FIBRE-REINFORCED PLASTICS
ISO 3597-1:2003 Textile-glass-reinforced plastics Determination of mechanical properties on rods made of roving-reinforced resin Part 1: General considerations and preparation of rods
ISO 22314:2006 Plastics — Glass-fibre-reinforced products — Determination of fibre length
BS ISO 1268-3:2000 Fibre-reinforced plastics. Methods of producing test plates Wet compression moulding
ISO 1268-2:2001 Fibre-reinforced plastics Methods of producing test plates Part 2: Contact and spray-up moulding
BS EN ISO 12736:2014 Petroleum and natural gas industries. Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
ISO 4901:2011 Reinforced plastics based on unsaturated-polyester resins Determination of the residual styrene monomer content, as well as the content of other volatile aromatic hydrocarbons, by gas chromatography
14/30298583 DC : 0 BS EN 13121-3 - GRP TANKS AND VESSELS FOR USE ABOVE GROUND - PART 3: DESIGN AND WORKMANSHIP
BS ISO 1268-1:2001 Fibre-reinforced plastics. Methods of producing test plates General conditions
BS ISO 3597-1:2003 Textile-glass-reinforced plastics. Determination of mechanical properties on rods made of roving-reinforced resin General considerations and preparation of rods
BS ISO 9163 : 1996 AMD 10351 TEXTILE GLASS - ROVINGS - MANUFACTURE OF TEST SPECIMENS AND DETERMINATION OF TENSILE STRENGTH OF IMPREGNATED ROVINGS
BS ISO 7510:2017 Plastics piping systems. Glass-reinforced plastics (GRP) components. Determination of the amounts of constituents
UNE-ISO 1268-1:2012 Fibre-reinforced plastics -- Methods of producing test plates -- Part 1: General conditions
UNE-ISO 1268-9:2012 Fibre-reinforced plastics. Methods of producing test plates. Part 9: Moulding of GMT/STC
I.S. EN 1013:2012 LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
EN ISO 14692-2:2017 Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 2: Qualification and manufacture (ISO 14692-2:2017)
ISO 1268-1:2001 Fibre-reinforced plastics Methods of producing test plates Part 1: General conditions
11/30242263 DC : 0 BS EN 4691-001 - AEROSPACE SERIES - TIE ROD WITH INTEGRATED BOLTS - TECHNICAL SPECIFICATION
BS EN ISO 9163:2005 Textile glass. Rovings. Manufacture of test specimens and determination of tensile strength of impregnated rovings
BS EN 12576:1998 Plastics. Fibre reinforced composites. Preparation of compression moulded test plates of SMC, BMC and DMC
BS EN 13677-3:2003 Reinforced thermoplastic moulding compounds. Specification for GMT Specific requirements
UNE-EN ISO 10350-2:2011 Plastics - Acquisition and presentation of comparable single-point data - Part 2: Long-fibre-reinforced plastics (ISO 10350-2:2011)
BS EN 14598-3:2005 Reinforced thermosetting moulding compounds. Specification for sheet moulding compound (SMC) and bulk moulding compound (BMC) Specific requirements
UNE-EN 1013:2013 Light transmitting single skin profiled plastics sheets for internal and external roofs, walls and ceilings - Requirements and test methods
ISO 7822:1990 Textile glass reinforced plastics — Determination of void content — Loss on ignition, mechanical disintegration and statistical counting methods
ISO 12736:2014 Petroleum and natural gas industries Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures
BS EN ISO 7822:1999 Textile glass reinforced plastics. Determination of void content. Loss on ignition, mechanical disintegration and statistical counting methods
12/30260913 DC : 0 BS EN 4717 - AEROSPACE SERIES - POLYETHERKETONE WITH 55% CONTINUOUS CARBON FIBRE BY VOLUME (PEEK-CF55)
BS EN 4691-1:2017 Aerospace series. Tie rod with integrated bolts Technical specification
EN 858-1:2002/A1:2004 SEPARATOR SYSTEMS FOR LIGHT LIQUIDS (E.G. OIL AND PETROL) - PART 1: PRINCIPLES OF PRODUCT DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
EN 14598-2:2005/AC:2006 REINFORCED THERMOSETTING MOULDING COMPOUNDS - SPECIFICATION FOR SHEET MOULDING COMPOUND (SMC) AND BULK MOULDING COMPOUND (BMC) - PART 2: METHODS OF TEST AND GENERAL REQUIREMENTS
EN 13677-3:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 3: Specific requirements
EN 13677-2:2003 Reinforced thermoplastic moulding compounds - Specification for GMT - Part 2: Methods of test and general requirements
EN 13706-3:2002 Reinforced plastics composites - Specifications for pultruded profiles - Part 3: Specific requirements
EN ISO 9163:2005 Textile glass - Rovings - Manufacture of test specimens and determination of tensile strength of impregnated rovings (ISO 9163:2005)
EN 13706-2:2002 Reinforced plastics composites - Specifications for pultruded profiles - Part 2: Methods of test and general requirements
EN ISO 12736:2014 Petroleum and natural gas industries - Wet thermal insulation coatings for pipelines, flow lines, equipment and subsea structures (ISO 12736:2014)
EN 14598-3:2005 Reinforced thermosetting moulding compounds - Specification for Sheet Moulding Compound (SMC) and Bulk Moulding Compound (BMC) - Part 3: Specific requirements
EN ISO 7822 : 1999 TEXTILE GLASS REINFORCED PLASTICS - DETERMINATION OF VOID CONTENT - LOSS ON IGNITION, MECHANICAL DISINTEGRATION AND STATISTICAL COUNTING METHODS
EN 1825-1:2004/AC:2006 GREASE SEPARATORS - PART 1: PRINCIPLES OF DESIGN, PERFORMANCE AND TESTING, MARKING AND QUALITY CONTROL
UNE-ISO 1268-2:2012 Fibre-reinforced plastics -- Methods of producing test plates -- Part 2: Contact and spray-up moulding
ISO 7510:2017 Plastics piping systems — Glass-reinforced plastics (GRP) components — Determination of the amounts of constituents
ISO 1268-4:2005 Fibre-reinforced plastics Methods of producing test plates Part 4: Moulding of prepregs
UNE-ISO 1268-4:2012 Fibre-reinforced plastics -- Methods of producing test plates -- Part 4: Moulding of prepregs
UNE-ISO 1268-3:2012 Fibre-reinforced plastics -- Methods of producing test plates -- Part 3: Wet compression moulding
07/30169818 DC : 0 BS EN 1013 - LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
BS ISO 1268-8:2004 Fibre-reinforced plastics. Methods of producing test plates Compression moulding of SMC and BMC
03/109038 DC : DRAFT MAY 2003 ISO 9163 - TEXTILE GLASS - ROVINGS - MANUFACTURE OF TEST SPECIMENS AND DETERMINATION OF TENSILE STRENGTH OF IMPREGNATED ROVINGS
UNI EN 1013 : 2015 LIGHT TRANSMITTING SINGLE SKIN PROFILED PLASTICS SHEETS FOR INTERNAL AND EXTERNAL ROOFS, WALLS AND CEILINGS - REQUIREMENTS AND TEST METHODS
UNE-ISO 1268-7:2012 Fibre-reinforced plastics. Methods of producing test plates. Part 7: Resin transfer moulding
ISO 1268-3:2000 Fibre-reinforced plastics Methods of producing test plates Part 3: Wet compression moulding
BS EN 13121-2:2003 GRP tanks and vessels for use above ground Composite materials. Chemical resistance
BS EN 1825-1:2004 Grease separators Principles of design, performance and testing, marking and quality control
BS EN 858-1:2002 Separator systems for light liquids (e.g. oil and petrol) Principles of product design, performance and testing, marking and quality control
EN 13121-2:2003 GRP tanks and vessels for use above ground - Part 2: Composite materials - Chemical resistance
DIN EN 1825-1:2004-12 Grease separators - Part 1: Principles of design, performance and testing, marking and quality control; German version EN 1825-1:2004

ISO 4793:1980 Laboratory sintered (fritted) filters — Porosity grading, classification and designation
ISO 11667:1997 Fibre-reinforced plastics — Moulding compounds and prepregs — Determination of resin, reinforced-fibre and mineral-filler content — Dissolution methods
ISO 472:2013 Plastics Vocabulary
ISO 8604:1988 Plastics — Prepregs — Definitions of terms and symbols for designations

View more information
£58.00
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.