We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • ISO 6162-1:2012

    Current The latest, up-to-date edition.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    Hydraulic fluid power Flange connections with split or one-piece flange clamps and metric or inch screws Part 1: Flange connectors, ports and mounting surfaces for use at pressures of 3,5 MPa (35 bar) to 35 MPa (350 bar), DN 13 to DN 127

    Available format(s):  Hardcopy, PDF, PDF 3 Users, PDF 5 Users, PDF 9 Users

    Language(s):  French, English

    Published date:  14-12-2012

    Publisher:  International Organization for Standardization

    Add to Watchlist

    Add To Cart

    Abstract - (Show below) - (Hide below)

    ISO 6162-1:2012 gives general and dimensional specifications for flanged heads, split flange clamps (FCS and FCSM), one-piece flange clamps (FC and FCM), ports and mounting surfaces applicable to four-screw, split and one-piece flange clamp type tube connectors and hose fittings for use at pressures of 3,5 MPa (35 bar ) to 35 MPa (350 bar). It also specifies the dimensions of the seals to be used, as well as the grooves that house the seals.

    ISO 6162-1:2012 also recognizes the need to accommodate metric screw fasteners (type 1), as well as to provide a means to use existing inch screw fasteners (type 2).

    These connections are intended for application in hydraulic systems on industrial and commercial products where it is desired to avoid the use of threaded connectors.

    Surges of pressure higher than the nominal ratings will reduce the ability of the flange connections to retain the hydraulic fluid. This needs to be taken into account in the design of the hydraulic system.

    General Product Information - (Show below) - (Hide below)

    Committee ISO/TC 131/SC 4
    Development Note Together with ISO 6162-2 supersedes ISO 6162. (12/2002) Supersedes ISO/DIS 6162-1. (12/2012)
    Document Type Standard
    Publisher International Organization for Standardization
    Status Current
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    03/110806 DC : DRAFT JUNE 2003 BS ISO 19879 - METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
    DIN ISO 6022 E : 2008 HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
    14/30274168 DC : 0 BS ISO 6020-3 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 3: COMPACT SERIES WITH BORES FROM 250 MM TO 500 MM
    09/30202316 DC : 0 BS EN 12514-4 - PARTS FOR SUPPLY SYSTEMS FOR CONSUMING UNITS WITH LIQUID FUELS - PART 4: SAFETY REQUIREMENTS AND TESTS - PIPINGS AND PARTS WITHIN PIPELINES
    BS ISO 6020-1:2007 (published 2007-10) Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Medium series
    SAE J 2551/2 : 2013 RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 2: GENERAL SPECIFICATIONS AND PERFORMANCE REQUIREMENTS
    BS PD ISO/TS 11672 : 2016 CONNECTORS FOR FLUID POWER AND GENERAL USE - DESIGNATION AND NOMENCLATURE
    SAE J 1065 : 2016 NOMINAL REFERENCE WORKING PRESSURES FOR STEEL HYDRAULIC TUBING
    SAE J 2614 : 2018 WELDED AND COLD-DRAWN, HIGH STRENGTH (500 MPA TENSILE STRENGTH) HYDRAULIC TUBING, FOR BENDING, FLARING, COLD FORMING, WELDING AND BRAZING
    SAE J 2551/3 : 2013 RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 3: PROCUREMENT
    16/30328245 DC : 0 BS ISO 6164 - HYDRAULIC FLUID POWER - FOUR-SCREW, ONE-PIECE SQUARE FLANGE CONNECTIONS FOR USE AT PRESSURES OF 42 MPA, DN 10 TO 80
    14/30284271 DC : 0 BS ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
    UNI ISO 12151-3 : 2012 CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
    ISO 12151-3:2010 Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
    SAE J 2551 : 2013 RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON AND ALLOY STEEL TUBING APPLICATIONS
    BS EN ISO 4413 : 2010 HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
    DIN ISO 12151-3 E : 2012 CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS (ISO 12151-3:2010)
    UNI ISO 17165-1 : 2012 HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS
    BS ISO 12151-3:2010 CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
    BS ISO 6020-2 : 2015 HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
    BS ISO 4081:2016 Rubber hoses and tubing for cooling systems for internal-combustion engines. Specification
    BS ISO 16874 : 2004 HYDRAULIC FLUID POWER - IDENTIFICATION OF MANIFOLD ASSEMBLIES AND THEIR COMPONENTS
    BS ISO 17165-1 : 2007 HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 1: DIMENSIONS AND REQUIREMENTS
    04/30098195 DC : DRAFT JUL 2004 ISO 6020-2 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 2: COMPACT SERIES
    DIN ISO 6020-1:2010-07 Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 1: Medium series (ISO 6020-1:2007)
    ISO 6022:2006 Hydraulic fluid power — Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series
    SAE J 846 : 2015 CODING SYSTEMS FOR IDENTIFICATION OF FLUID CONDUCTORS AND CONNECTORS
    07/30163202 DC : 0 BS ISO 12151-3 - CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
    UNI EN ISO 19879 : 2011 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
    09/30193685 DC : 0 BS ISO 4081 - RUBBER HOSES AND TUBING FOR COOLING SYSTEMS FOR INTERNAL-COMBUSTION ENGINES - SPECIFICATION
    BS ISO 6020-3:2015 Hydraulic fluid power. Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Compact series with bores from 250 mm to 500 mm
    BS ISO 6022:2006 (published 2006-02) Hydraulic fluid power. Mounting dimensions for single rod cylinders, 25M Pa (250 bar) series
    BS ISO 10946 : 1999 HYDRAULIC FLUID POWER - GAS-LOADED ACCUMULATORS WITH SEPARATOR - SELECTION OF PREFERRED HYDRAULIC PORTS
    06/30128831 DC : DRAFT MAR 2006 ISO 6020-1 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 16 MPA (160 BAR) SERIES - PART 1: MEDIUM SERIES
    BS PD ISO/TS 17165-2 : 2013 HYDRAULIC FLUID POWER - HOSE ASSEMBLIES - PART 2: PRACTICES FOR HYDRAULIC HOSE ASSEMBLIES
    SAE J 518/1 : 2013 HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 1: 3.5 MPA TO 35 MPA (CODE 61)
    ISO 4081:2016 Rubber hoses and tubing for cooling systems for internal-combustion engines Specification
    DIN EN ISO 4413:2011-04 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
    UNE-EN ISO 4413:2011 Hydraulic fluid power - General rules and safety requirements for systems and their components (ISO 4413:2010)
    NF EN ISO 4413 : 2011 HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS
    SAE J 2551/1 : 2013 RECOMMENDED PRACTICES FOR FLUID CONDUCTOR CARBON, ALLOY AND HIGH STRENGTH LOW ALLOY STEEL TUBING APPLICATIONS - PART 1: DESIGN AND FABRICATION
    SAE J 2593 : 2015 INFORMATION REPORT FOR THE INSTALLATION OF FLUID CONDUCTORS AND CONNECTORS
    ISO 6020-1:2007 Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 1: Medium series
    SAE J 515 : 2015 SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS
    ISO 6164:1994 Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
    ISO 17165-1:2007 Hydraulic fluid power Hose assemblies Part 1: Dimensions and requirements
    SAE J 1677 : 2016 TESTS AND PROCEDURES FOR CARBON STEEL AND HIGH STRENGTH LOW ALLOY STEEL TUBING
    NF ISO 12151-3 : 2010 CONNECTIONS FOR HYDRAULIC FLUID POWER AND GENERAL USE - HOSE FITTINGS - PART 3: HOSE FITTINGS WITH ISO 6162-1 OR ISO 6162-2 FLANGE ENDS
    SAE J 518/2 : 2017 HYDRAULIC FLANGED TUBE, PIPE, AND HOSE CONNECTIONS, 4-SCREW FLANGE CONNECTION - PART 2: 42 MPA (CODE 62)
    DIN EN ISO 19879:2011-01 Metallic tube connections for fluid power and general use - Test methods for hydraulic fluid power connections (ISO 19879:2010)
    04/30098199 DC : DRAFT JUL 2004 ISO 6022 - HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
    ISO 16874:2004 Hydraulic fluid power Identification of manifold assemblies and their components
    SAE J 518/3 : 2015 HYDRAULIC FLANGE CLAMPS, 2-SCREW FLANGE CONNECTION TO BE USED WITH SAE J518-1, (CODE 61) CONNECTIONS WHERE ONLY LOW PRESSURE IS REQUIRED
    ISO 6020-3:2015 Hydraulic fluid power — Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series — Part 3: Compact series with bores from 250 mm to 500 mm
    ISO 6020-2:2015 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series Part 2: Compact series
    DIN EN ISO 19879 E : 2011 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
    ISO 19859:2016 Gas turbine applications Requirements for power generation
    14/30244780 DC : 0 BS ISO 19859 - GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
    BS EN ISO 19879:2010 (published 2010-10) Metallic tube connections for fluid power and general use. Test methods for hydraulic fluid power connections
    BS EN ISO 16330 : 2003 RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS
    ISO 4413:2010 Hydraulic fluid power General rules and safety requirements for systems and their components
    BS ISO 19859 : 2016 GAS TURBINE APPLICATIONS - REQUIREMENTS FOR POWER GENERATION
    ISO 16330:2003 Reciprocating positive displacement pumps and pump units Technical requirements
    ISO 19879:2010 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
    I.S. EN ISO 19879:2010 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
    EN ISO 19879:2010 METALLIC TUBE CONNECTIONS FOR FLUID POWER AND GENERAL USE - TEST METHODS FOR HYDRAULIC FLUID POWER CONNECTIONS
    DIN ISO 6022:2008-06 HYDRAULIC FLUID POWER - MOUNTING DIMENSIONS FOR SINGLE ROD CYLINDERS, 25 MPA (250 BAR) SERIES
    DIN EN ISO 16330:2004-08 Reciprocating positive displacement pumps and pump units - Technical requirements (ISO 16330:2003)
    DIN ISO 12151-3:2012-08 Connections for hydraulic fluid power and general use - Hose fittings - Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends (ISO 12151-3:2010)
    EN ISO 16330 : 2003 RECIPROCATING POSITIVE DISPLACEMENT PUMPS AND PUMP UNITS - TECHNICAL REQUIREMENTS
    EN ISO 4413 : 2010 HYDRAULIC FLUID POWER - GENERAL RULES AND SAFETY REQUIREMENTS FOR SYSTEMS AND THEIR COMPONENTS

    Standards Referencing This Book - (Show below) - (Hide below)

    ISO 68-2:1998 ISO general purpose screw threads Basic profile Part 2: Inch screw threads
    ISO 5598:2008 Fluid power systems and components Vocabulary
    ISO 1101:2017 Geometrical product specifications (GPS) Geometrical tolerancing Tolerances of form, orientation, location and run-out
    SAE J 429 : 2014 MECHANICAL AND MATERIAL REQUIREMENTS FOR EXTERNALLY THREADED FASTENERS
    ISO 724:1993 ISO general-purpose metric screw threads Basic dimensions
    ISO 4017:2014 Fasteners Hexagon head screws Product grades A and B
    ISO 6708:1995 Pipework components Definition and selection of DN (nominal size)
    ISO 4762:2004 Hexagon socket head cap screws
    ISO 5864:1993 ISO inch screw threads Allowances and tolerances
    ISO 1302:2002 Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation
    SAE J 515 : 2015 SPECIFICATION FOR O-RING MATERIALS USED WITH HYDRAULIC CONNECTORS
    ISO 12151-3:2010 Connections for hydraulic fluid power and general use Hose fittings Part 3: Hose fittings with ISO 6162-1 or ISO 6162-2 flange ends
    ISO 7089:2000 Plain washers Normal series Product grade A
    ISO 68-1:1998 ISO general purpose screw threads Basic profile Part 1: Metric screw threads
    ISO 19879:2010 Metallic tube connections for fluid power and general use Test methods for hydraulic fluid power connections
    ISO 6164:1994 Hydraulic fluid power Four-screw, one-piece square-flange connections for use at pressures of 25 MPa and 40 MPa (250 bar and 400 bar)
    ISO 80000-1:2009 Quantities and units Part 1: General
    ISO 725:2009 ISO inch screw threads Basic dimensions
    ISO 273:1979 Fasteners Clearance holes for bolts and screws
    ASME B18.3 : 2012 SOCKET CAP, SHOULDER, SET SCREWS, AND HEX KEYS (INCH SERIES)
    ISO 9227:2017 Corrosion tests in artificial atmospheres Salt spray tests
    ISO 261:1998 ISO general purpose metric screw threads General plan
    ISO 10763:1994 Hydraulic fluid power Plain-end, seamless and welded precision steel tubes Dimensions and nominal working pressures
    ISO 3601-1:2012 Fluid power systems — O-rings — Part 1: Inside diameters, cross-sections, tolerances and designation codes
    ASTM A 574 : 2017 : REDLINE Standard Specification for Alloy Steel Socket-Head Cap Screws
    ISO 13715:2017 Technical product documentation Edges of undefined shape Indication and dimensioning
    ISO 3601-3:2005 Fluid power systems O-rings Part 3: Quality acceptance criteria
    ISO 48:2010 Rubber, vulcanized or thermoplastic Determination of hardness (hardness between 10 IRHD and 100 IRHD)
    ISO 263:1973 ISO inch screw threads General plan and selection for screws, bolts and nuts Diameter range 0,06 to 6 in
    ISO 898-1:2013 Mechanical properties of fasteners made of carbon steel and alloy steel Part 1: Bolts, screws and studs with specified property classes Coarse thread and fine pitch thread
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective