MIL-DTL-17060 Revision G:2009
Current
Current
The latest, up-to-date edition.
MOTORS, ALTERNATING CURRENT, INTEGRAL-HORSEPOWER, SHIPBOARD USE
Available format(s)
PDF
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES
APPENDIX A - EXAMINATION OF SERVICE A MOTORS
APPENDIX B - ENGINEERING DRAWINGS TECHNICAL CONTENT
REQUIREMENTS
APPENDIX C - TEST PROCEDURES FOR MOTOR EFFICIENCY
APPENDIX D - TEST REPORT TECHNICAL CONTENT REQUIREMENTS
APPENDIX E - CERTIFICATION DATA/REPORT TECHNICAL CONTENT
REQUIREMENTS
APPENDIX F - SHOCK TEST REPORT TECHNICAL CONTENT REQUIREMENTS
APPENDIX G - EQUIPMENT AIRBORNE AND STRUCTUREBORNE NOISE
MEASUREMENTS TEST REPORT - TECHNICAL CONTENT
REQUIREMENTS
APPENDIX H - INSPECTION AND TEST PLAN - TECHNICAL CONTENT
REQUIREMENTS
INDEX
Specifies the requirements for three-phase, alternating current (AC) motors for shipboard use in frame sizes not less than 182.
| Committee |
FSC 6105
|
| DevelopmentNote |
Supersedes MIL M 17060 (F). (01/2009)
|
| DocumentType |
Standard
|
| Pages |
199
|
| PublisherName |
US Military Specs/Standards/Handbooks
|
| Status |
Current
|
| Supersedes |
| MIL-DTL-24151 Revision B:2016 | DOORS, ROLLER CURTAIN AND HINGED SLAT, AND ASSOCIATED OPERATING EQUIPMENT |
| MIL-DTL-917 Revision F:2014 | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS FOR |
| MIL STD 11991 : A | GENERAL STANDARD FOR PARTS, MATERIALS, AND PROCESSES |
| MIL-DTL-32408 Base Document:2012 | INTEGRAL MOTOR PUMP (IMP) |
| MIL-DTL-32572 Base Document:2017 | Anchor Windlass, Electro-Mechanical, Vertical, Two-Speedand Variable-Speed |
| MIL-PRF-24755 Revision B:2010 | Fans, Vaneaxial, High Pressure, Naval Shipboard |
| MIL-PRF-18953 Revision C:2005 | FANS, VANEAXIAL AND TUBEAXIAL, VENTILATION AND AIR CONDITIONING, NAVAL SHIPBOARD |
| MIL-DTL-17840 Revision D:2018 | PUMPS, CENTRIFUGAL, CLOSE-COUPLED, NAVY STANDARD (FOR SURFACE SHIP APPLICATION) |
| MIL-I-24092 Revision D:1993 | INSULATING VARNISHES AND SOLVENTLESS RESINS FOR APPLICATION BY THE DIP PROCESS |
| A-A-59589 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, FILLING SLOT, DIMENSION SERIES 03 |
| NEMA MW 1000 : 2016 | MAGNET WIRE |
| ABMA 9 : 2015 | LOAD RATINGS AND FATIGUE LIFE FOR BALL BEARINGS |
| MIL-STD-2037 Base Document:1991 | PROCEDURE TO OBTAIN CERTIFICATION FOR ELECTRIC MOTOR SEALED INSULATION SYSTEMS |
| A-A-59586 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 04 |
| A-A-59641 Revision B:2011 | BEARING, BALL, ANNULAR, DOUBLE ROW, ANGULAR CONTACT, FILLING SLOT, VERTEX OF CONTACT ANGLES OUTSIDE BEARING, DIMENSION SERIES 33 |
| ASTM A 47/A47M : 1999 | Standard Specification for Ferritic Malleable Iron Castings |
| MIL-C-24707-5 Base Document:1989 | CASTINGS, DUCTILE IRON AND AUSTENITIC DUCTILE IRON |
| A-A-59640 Revision B:2011 | BEARING, BALL, ANNULAR, DOUBLE ROW, ANGULAR CONTACT, FILLING SLOT, VERTEX OF CONTACT ANGLES OUTSIDE BEARING, DIMENSION SERIES 32 |
| MIL-DTL-917 Revision F:2014 | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS FOR |
| A-A-59629 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 23 DEGREES THROUGH 32 DEGREES, DIMENSION SERIES 02 |
| A-A-59637 Revision B:2011 | BEARING, BALL, ANNULAR, DOUBLE ROW, ANGULAR CONTACT, NON-FILLING SLOT, VERTEX OF CONTACT ANGLES OUTSIDE BEARING, DIMENSION SERIES 33 |
| ASTM A 29/A29M : 2016 : REDLINE | Standard Specification for General Requirements for Steel Bars, Carbon and Alloy, Hot-Wrought |
| SAE AMS 7276H : 2011 | RUBBER: FLUOROCARBON (FKM) HIGH-TEMPERATURE-FLUID RESISTANT LOW COMPRESSION SET FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
| MIL-DTL-21248 Revision D:2015 | Ring, Retaining (Tapered and Reduced Section Type) |
| A-A-59685 Base Document:2001 | Grease, Sealed Ball and Roller Bearing |
| A-A-59596 Revision C:2009 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, CARTRIDGE TYPE WITHOUT GREASE PLUG, DIMENSION SERIES 33 |
| A-A-59584 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 02 |
| MIL-PRF-17331 Revision K:2013 | LUBRICATING OIL, STEAM TURBINE AND GEAR, MODERATE SERVICE |
| A-A-59632 Revision B:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 DEGREES THROUGH 45 DEGREES, DIMENSION SERIES 10 |
| IEC TS 61934:2011 | Electrical insulating materials and systems - Electrical measurement of partial discharges (PD) under short rise time and repetitive voltage impulses |
| MIL-DTL-1222 Revision J:2000 | STUDS, BOLTS, SCREWS AND NUTS FOR APPLICATIONS WHERE A HIGH DEGREE OF RELIABILITY IS REQUIRED; GENERAL SPECIFICATION FOR |
| A-A-59627 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 11 DEGREES THROUGH 22 DEGREES, DIMENSION SERIES 04 |
| SAE AMS 2469 : 2014 | HARD ANODIC COATING ON ALUMINUM AND ALUMINUM ALLOYS |
| MIL-L-19140 Revision E:1984 | LUMBER & PLYWOOD, FIRE RETARDANT TREATED |
| ASTM A 683 : 2016 : REDLINE | Standard Specification for Nonoriented Electrical Steel, Semiprocessed Types |
| QQ-B-654 Revision A:1980 | BRAZING ALLOY, SILVER |
| A-A-59630 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 23 DEGREES THROUGH 32 DEGREES, DIMENSION SERIES 03 |
| MIL-STD-740-2 Base Document:1986 | STRUCTURE BORNE VIBRATORY ACCELERATION MEASUREMENTS ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT |
| MIL C 24707/1 : 0 | CASTINGS, FERROUS, FOR MACHINERY AND STRUCTURAL APPLICATIONS |
| SAE AMS 7259 : 2013 | RUBBER: FLOUROCARBON (FKM), HIGH TEMPERATURE/FLUID RESISTANT, LOW COMPRESSION SET/85 TO 95 HARDNESS, FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS |
| MIL-I-24178 Base Document:1966 | INSULATION TAPE, ELECTRICAL, SEMI-CURED THERMOSETTING RESIN TREATED GLASS, ARMATURE BANDING, NAVAL SHIPBOARD |
| A-A-59638 Revision B:2011 | Bearing, Ball, Annular, Double Row, Angular Contact, Non-Filling Slot, Vertex of Contact Angles Inside Bearing, Dimension Series 32 |
| ASTM A 757/A757M : 2015 : REDLINE | Standard Specification for Steel Castings, Ferritic and Martensitic, for Pressure-Containing and Other Applications, for Low-Temperature Service |
| MIL-B-17931 Revision E:1987 | BEARINGS, BALL, ANNULAR, FOR QUIET OPERATION |
| MIL-STD-461 Revision G:2015 | REQUIREMENTS FOR THE CONTROL OF ELECTROMAGNETIC INTERFERENCE CHARACTERISTICS OF SUBSYSTEMS AND EQUIPMENT |
| ASTM D 4727/D4727M : 2017 : REDLINE | Standard Specification for Corrugated and Solid Fiberboard Sheet Stock (Container Grade) and Cut Shapes |
| A-A-59626 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 11 DEGREES THROUGH 22 DEGREES, DIMENSION SERIES 03 |
| IEC 60034-18-41:2014 | Rotating electrical machines - Part 18-41: Partial discharge free electrical insulation systems (Type I) used in rotating electrical machines fed from voltage converters - Qualification and quality control tests |
| A-A-59597 Revision C:2009 | BEARING, BALL, ANNULAR, DOUBLE ROW, RADIAL, INTERNAL SELF-ALIGNING, DIMENSION SERIES 02 |
| A-A-59636 Revision B:2011 | BEARING, BALL, ANNULAR, DOUBLE ROW, ANGULAR CONTACT, NON-FILLING SLOT, VERTEX OF CONTACT ANGLES OUTSIDE BEARING, DIMENSION SERIES 32 |
| A-A-59583 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 10 |
| A-A-59600 Revision C:2009 | BEARING, BALL, ANNULAR, DOUBLE ROW, RADIAL, INTERNAL SELF-ALIGNING, DIMENSION SERIES 23 |
| ASTM B 30 : 2016 : REDLINE | Standard Specification for Copper Alloys in Ingot Form |
| A-A-59599 Revision C:2009 | BEARING, BALL, ANNULAR, DOUBLE ROW, RADIAL, INTERNAL SELF-ALIGNING, DIMENSION SERIES 22 |
| MIL S 901 : D | SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR |
| A-A-59625 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 11 DEGREES THROUGH 22 DEGREES, DIMENSION SERIES 02 |
| A-A-59623 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 11 DEGREES THROUGH 22 DEGREES, DIMENSION SERIES 19 |
| MIL-STD-108 Revision E:1966 | DEFINITION OF AND BASIC REQUIREMENT FOR ENCLOSURE FOR ELECTRIC AND ELECTRONIC EQUIPMENT |
| A-A-59624 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 11 DEGREES THROUGH 22 DEGREES, DIMENSION SERIES 10 |
| A-A-59634 Revision B:2010 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 DEGREES THROUGH 45 DEGREES, DIMENSION SERIES 03 |
| A-A-59582 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 19 |
| A-A-59587 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, FILLING SLOT, DIMENSION SERIES 02 |
| A-A-59633 Revision B:2010 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 DEGREES THROUGH 45 DEGREES, DIMENSION SERIES 02 |
| ASTM A 677 : 2016 : REDLINE | Standard Specification for Nonoriented Electrical Steel Fully Processed Types |
| MIL-STD-1474 Revision E:2015 | NOISE LIMITS |
| A-A-59628 Revision C:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 23 DEGREES THROUGH 32 DEGREES, DIMENSION SERIES 10 |
| MIL-P-15024-5 Base Document:1971 | PLATE, IDENTIFICATION |
| A-A-59635 Revision B:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 33 DEGREES THROUGH 45 DEGREES, DIMENSION SERIES 04 |
| ABMA 20 : 2011 | RADIAL BEARINGS OF BALL, CYLINDRICAL ROLLER AND SPHERICAL ROLLER TYPES - METRIC DESIGN |
| IEEE 112-2004 | IEEE Standard Test Procedure for Polyphase Induction Motors and Generators |
| MIL-DTL-2036 Revision E:2014 | ENCLOSURES FOR ELECTRIC AND ELECTRONIC EQUIPMENT, NAVAL SHIPBOARD |
| MIL-DTL-15024 Revision F:1997 | Plates and Tags for Identification of Equipment, General Specification for |
| ASTM B21/B 21M : 2014-10 | SPECIFICATION FOR NAVAL BRASS ROD, BAR, AND SHAPES |
| MIL-DTL-18240 Revision F:1997 | FASTENER ELEMENT, SELF-LOCKING, THREADED FASTENER, 250 DEGREES F MAXIMUM |
| A-A-59631 Revision B:2011 | BEARING, BALL, ANNULAR, SINGLE ROW, ANGULAR CONTACT, CONTACT ANGLE 23 DEGREES THROUGH 32 DEGREES, DIMENSION SERIES 04 |
| FED-STD-H28 Revision A:1994 | Screw-Thread Standards for Federal Services |
| A-A-59598 Revision C:2009 | BEARING, BALL, ANNULAR, DOUBLE ROW, RADIAL, INTERNAL SELF-ALIGNING, DIMENSION SERIES 03 |
| A-A-59639 Revision B:2011 | BEARING, BALL, ANNULAR, DOUBLE ROW, ANGULAR CONTACT, FILLING SLOT, VERTEX OF CONTACT ANGLES INSIDE BEARING, DIMENSION SERIES 33 |
| MIL-M-24738 Base Document:1990 | MONITORS, HIGH TEMPERATURE MOTOR PROTECTION |
| A-A-59720 Base Document:2002 | SEALING AND LOCKING COMPOUNDS, SINGLE-COMPONENT |
| MIL-E-16298 Revision D:1989 | ELECTRIC MACHINES HAVING ROTATING PARTS AND ASSOCIATED REPAIR PARTS, PACKAGING OF |
| A-A-59581 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, BORE DIAMETERS UNDER 10 MM |
| A-A-59595 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, CARTRIDGE TYPE WITHOUT GREASE PLUG, DIMENSION SERIES 32 |
| A-A-59585 Revision C:2008 | BEARING, BALL, ANNULAR, SINGLE ROW, RADIAL, NON-FILLING SLOT, DIMENSION SERIES 03 |
| AWS A5.8 : 1992 | FILLER METALS FOR BRAZING AND BRAZE WELDING, SPECIFICATION FOR |
£16.70
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.