VALVES, CHECK, IN-LINE, FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID, GENERAL SPECIFICATION FOR

Amended by

MIL-DTL-24630 Revision A Notice 1 - Validation:2019

Available format(s)

PDF

Language(s)

English

Publisher

US Military Specs/Standards/Handbooks

1. SCOPE
2. APPLICABLE DOCUMENTS
3. REQUIREMENTS
4. VERIFICATION
5. PACKAGING
6. NOTES

Specifies the requirements for in-line check valves for use in hydraulic fluid and lubricating oil fluid systems of naval ships operating up to a maximum pressure of 3,000 pounds per square inch (lb/in[2]).

Committee	FSC 4820
DevelopmentNote	Supersedes MIL V 24630. (07/2014)
DocumentType	Standard
Pages	14
ProductNote	NEW CHILD NOT 1 2019 IS NOW ADDED
PublisherName	US Military Specs/Standards/Handbooks
Status	Current
Supersedes	MIL V 24630 : 0

MIL-DTL-24630-1 Revision B:2014	VALVES, CHECK, IN-LINE, NON-REVERSIBLE INSTALLATION FOR HYDRAULIC FLUID AND LUBRICATING OIL FLUID
SAE AS 4716 : 2011	GLAND DESIGN, O-RING AND OTHER SEALS
MIL-PRF-6083 Revision G:2013	HYDRAULIC FLUID, PETROLEUM BASE, FOR PRESERVATION AND OPERATION
SAE AS 5781 : 2015	RETAINERS (BACKUP RINGS), HYDRAULIC AND PNEUMATIC, POLYTETRAFLUOROETHYLENE RESIN, SINGLE TURN, SCARF-CUT, FOR USE IN AS4716 GLANDS
MIL-PRF-27617 Revision G:2011	GREASE, AIRCRAFT AND INSTRUMENT, FUEL AND OXIDIZER RESISTANT
MIL-STD-810 Revision G:2008	ENVIRONMENTAL ENGINEERING CONSIDERATIONS AND LABORATORY TESTS
MIL-PRF-5606 Revision H:2002	HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT, MISSILE, AND ORDNANCE
SAE AMS 7276H : 2011	RUBBER: FLUOROCARBON (FKM) HIGH-TEMPERATURE-FLUID RESISTANT LOW COMPRESSION SET FOR SEALS IN FUEL SYSTEMS AND SPECIFIC ENGINE OIL SYSTEMS
SAE AS 5782 : 2015	RETAINERS (BACKUP RINGS), HYDRAULIC AND PNEUMATIC, POLYTETRAFLUOROETHYLENE RESIN, SOLID, UN-CUT, FOR USE IN AS4716 GLANDS
MIL-PRF-17331 Revision K:2013	LUBRICATING OIL, STEAM TURBINE AND GEAR, MODERATE SERVICE
ASME B46.1 : 2009	SURFACE TEXTURE (SURFACE ROUGHNESS, WAVINESS, AND LAY)
SAE AS 598 : 2012	AEROSPACE MICROSCOPIC SIZING AND COUNTING OF PARTICULATE CONTAMINATION FOR FLUID POWER SYSTEMS
MIL-STD-740-2 Base Document:1986	STRUCTURE BORNE VIBRATORY ACCELERATION MEASUREMENTS ACCEPTANCE CRITERIA OF SHIPBOARD EQUIPMENT
SAE AS 8791 : 2014	HYDRAULIC AND PNEUMATIC RETAINERS (BACK-UP RINGS), POLYTETRAFLUOROETHYLENE (PTFE) RESIN
SAE AMS QQ S 763D : 2013(S2015)	STEEL, CORROSION RESISTANT, BARS, WIRE, SHAPES, AND FORGINGS
MIL-G-5514 Revision G:1993	GLAND DESIGN, PACKINGS, HYDRAULIC GENERAL REQUIREMENTS FOR
NAVSEA S9074 AR GIB 010/278 : 0	REQUIREMENTS FOR FABRICATION WELDING AND INSPECTION, AND CASTING INSPECTION AND REPAIR FOR MACHINERY, PIPING, AND PRESSURE VESSELS
MIL-PRF-17672 Revision E:2010	Hydraulic Fluid, Petroleum, Inhibited
MIL S 901 : D	SHOCK TESTS, HI [HIGH IMPACT] SHIPBOARD MACHINERY, EQUIPMENT AND SYSTEMS, REQUIREMENTS FOR
MIL-PRF-83282 Revision D:1997	HYDRAULIC FLUID, FIRE RESISTANT, SYNTHETIC HYDROCARBON BASE, METRIC, NATO CODE NUMBER H-537
SAE AS 4059F : 2013	AEROSPACE FLUID POWER - CONTAMINATION CLASSIFICATION FOR HYDRAULIC FLUIDS
MIL-P-15024-5 Base Document:1971	PLATE, IDENTIFICATION
MIL-DTL-15024 Revision F:1997	Plates and Tags for Identification of Equipment, General Specification for
MIL-DTL-17111 Revision E:2012	FLUID, POWER TRANSMISSION
FED-STD-H28 Revision A:1994	Screw-Thread Standards for Federal Services
MIL-C-15726 Revision F:1988	COPPER NICKEL ALLOY, SHEET, PLATE, STRIP, BAR, ROD AND WIRE
MIL-STD-167-1 Revision A:2005	MECHANICAL VIBRATIONS OF SHIPBOARD EQUIPMENT (TYPE 1 - ENVIRONMENTAL AND TYPE 2 - INTERNALLY EXCITED)
MIL-H-22072 Revision C:1984	HYDRAULIC FLUID, CATAPULT, NATO CODE NUMBER H-579
MIL-H-19457 Revision D:1989	HYDRAULIC FLUID, FIRE RESISTANT, NON NEUROTOXIC