• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

NF EN ISO 2818 : 1997

Current
Current

The latest, up-to-date edition.

PLASTICS - PREPARATION OF TEST SPECIMENS BY MACHINING
Published date

12-01-2013

Committees responsible
National foreword
Introduction
1 Method
2 Normative references
3 Definitions
4 Test specimens
5 Machinery and tools
6 Procedure
7 Test reports
Annex
A (informative) Bibliography
Table
1 Recommended machining conditions for four types of test
    specimen and for notches
Figures
1 Geometry of the active part of cutting tools
2 Shape of milling chips
3 Chip thickness ds in the range between 0.003 mm and 0.007 mm
    versus rotational speed n and feed speed vf of a
    milling machine (R = 40 mm)
4 Example of a circular cutter (half-section of a diamond-
    edged cutter)

Le présent document prescrit des méthodes de préparation d'éprouvettes en plastique par usinage à partir de plaques ou de produits finis. La présente Norme internationale établit les principes et modes opératoires généraux à suivre lors de l'usinage et de la production des entailles sur les éprouvettes produites à partir de plastiques moulés par compression et par injection, de feuilles extrudées, de plaques, et de produits partiellement ou entièrement finis. Il convient d'appliquer les conditions normalisées générales suivantes pour établir une base permettant d'obtenir des conditions reproductibles en matière d'usinage et de production d'entailles. On présume, cependant, que les modes opératoires exacts à utiliser seront choisis parmi ou précisés dans les spécifications relatives à la matière concernée ou dans les normes afférentes aux méthodes d'essai particulières. Si les modes opératoires spécifiés ne sont pas suffisamment détaillés, il est essentiel que les parties concernées s'accordent sur les conditions à utiliser.

DevelopmentNote
Supersedes NFT 58-001: 1982 (09/2001)
DocumentType
Standard
PublisherName
Association Francaise de Normalisation
Status
Current
Supersedes

NFM 60 326 : 2006 NUCLEAR ENERGY - NUCLEAR FUEL TECHNOLOGY - WASTE - DETERMINATION OF TRITIATED WATER EFFECTIVE DIFFUSION COEFFICIENT IN CONFINING MATERIALS
NFM 60 324 : 2005 NUCLEAR ENERGY - NUCLEAR FUEL CYCLE TECHNOLOGY - DETERMINATION OF LEACHING RESISTANCE OF HOMOGENEOUS WASTE BLOCKS
NFF 01 281 : 2014 RAILWAY ROLLING STOCK - PARTS IN FIBRE-REINFORCED THERMOSETTING COMPOSITES - SPECIFICATIONS, TEST METHODS, MANUFACTURING, QUALIFICATION AND ASSESSMENT OF CONFORMITY
NF ISO 15310 : 2001 COMPOSITES PLASTIQUES RENFORCES DE FIBRES - DETERMINATION DU MODULE DE CISAILLEMENT DANS LE PLAN PAR LA METHODE DE TORSION DE PLAQUE
NF EN ISO 2580-2 : 2004 PLASTICS - ACRYLONITRILE-BUTADIENE-STYRENE (ABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
NF EN ISO 15013 : 2007 PLASTICS - EXTRUDED SHEETS OF POLYPROPYLENE (PP) - REQUIREMENTS AND TEST METHODS
NF EN ISO-62 : 2008 PLASTICS - DETERMINATION OF WATER ABSORPTION
NFT 54 405-1 : 2002 UNPLASTICIZED POLY (VINYL CHLORIDE) (PVC-U) EXTRUDED OR COEXTRUDED PROFILES FOR OUTSIDE USE - SPECIFICATIONS AND TEST METHODS - PART 1: SOLID WALL PVC-U
NF EN ISO 180 : 2001 AMD 2 2013 PLASTICS - DETERMINATION OF IZOD IMPACT STRENGTH
NF EN ISO 10366-2 : 2004 PLASTICS - METHYL METHACRYLATE-ACRYLONITRILE-BUTADIENE-STYRENE (MABS) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
NF EN ISO 2898-2 : 2009 PLASTICS - PLASTICIZED POLY(VINYL CHLORIDE) (PVC-P) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
XP T54 990 : 2018 XP POLYETHYLENE (PE) PIPES AND FITTINGS - DETERMINATION OF THE RESISTANCE TO CRACK INITIATION AND SLOW CRACK GROWTH ON NOTCHED CYLINDRICAL BARS UNDER CONSTANT LOAD (NCBT)
NF EN ISO 2897-2 : 2004 PLASTICS - IMPACT-RESISTANT POLYSTYRENE (PS-I) MOULDING AND EXTRUSION MATERIALS - PART 2: PREPARATION OF TEST SPECIMENS AND DETERMINATION OF PROPERTIES
NF EN ISO 8256 : 2005 PLASTICS - DETERMINATION OF TENSILE-IMPACT STRENGTH

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.