• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

NSF 358-1 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

POLYETHYLENE PIPE AND FITTINGS FOR WATER-BASED GROUND-SOURCE 'GEOTHERMAL' HEAT PUMP SYSTEMS
Available format(s)

Hardcopy , PDF

Superseded date

06-02-2020

Language(s)

English

Published date

01-01-2014

1 General
2 Normative References
3 Definitions
4 Material Requirements
5 General Requirements
6 Marking Requirements
7 Quality Assurance

Pertains to plastic piping system components as well as non-plastic components of the ground loop heat exchanger including, but not limited to, pipes and fittings used in water-based ground-source heat pump systems.

DocumentType
Standard
Pages
20
PublisherName
NSF International
Status
Superseded
SupersededBy
Supersedes

ICC IRC CODE AND COMMENTARY VOLUME 2 : 2015 IRC® Code and Commentary, Volume 2
ICC IMC Code and Commentary : 2015 IMC® Code and Commentary

ASTM F 1588 : 1996 Standard Test Method for Constant Tensile Load Joint Test (CTLJT)
ASTM D 3261 : 2016-11 SPECIFICATION FOR BUTT HEAT FUSION POLYETHYLENE (PE) PLASTIC FITTINGS FOR POLYETHYLENE (PE) PLASTIC PIPE AND TUBING
ASTM D 543 : 2014 : REDLINE Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents
PPI TR 3 : 2017 POLICIES AND PROCEDURES FOR DEVELOPING HYDROSTATIC DESIGN BASIS (HDB), HYDROSTATIC DESIGN STRESSES (HDS), PRESSURE DESIGN BASIS (PDB), STRENGTH DESIGN BASIS (SDB), MINIMUM REQUIRED STRENGTH (MRS) RATINGS, AND CATEGORIZED REQUIRED STRENGTH (CRS) FOR THERMOPLASTIC PIPING MATERIALS OR PIPE
CSA B137.1 : 2009 GEN INS 1 11 POLYETHYLENE (PE) PIPE, TUBING, AND FITTINGS FOR COLD-WATER PRESSURE SERVICES
ASTM D 2683 : 2014 : REDLINE Standard Specification for Socket-Type Polyethylene Fittings for Outside Diameter-Controlled Polyethylene Pipe and Tubing
ASTM F 714 : 2013 : REDLINE Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Outside Diameter
AWWA C901 : 2017 POLYETHYLENE (PE) PRESSURE PIPE AND TUBING, 3/4 IN. (19 MM) THROUGH 3 IN. (76 MM), FOR WATER SERVICE
ASTM F 1055 : 2016-09 SPECIFICATION FOR ELECTROFUSION TYPE POLYETHYLENE FITTINGS FOR OUTSIDE DIAMETER CONTROLLED POLYETHYLENE AND CROSSLINKED POLYETHYLENE (PEX) PIPE AND TUBING
ASTM D 2290 : 2016-12 TEST METHOD FOR APPARENT HOOP TENSILE STRENGTH OF PLASTIC OR REINFORCED PLASTIC PIPE
ASTM D 3350 : 2014 : REDLINE Standard Specification for Polyethylene Plastics Pipe and Fittings Materials
ASTM D 3035 : 2015 : REDLINE Standard Specification for Polyethylene (PE) Plastic Pipe (DR-PR) Based on Controlled Outside Diameter
ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics

View more information
£87.66
Excluding VAT

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.