ONORM EN 12012-4 : 2010

Name: ONORM EN 12012-4 : 2010
Brand: ON

Withdrawn

View Superseded by

PLASTICS AND RUBBER MACHINES - SIZE REDUCTION MACHINES - PART 4: SAFETY REQUIREMENTS FOR AGGLOMERATORS

Withdrawn date

15-07-2019

Published date

12-01-2013

Publisher

Osterreichisches Normungsinstitut/Austrian Standards

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 List of significant hazards
  4.1 Mechanical hazards
  4.2 Thermal hazards
  4.3 Noise hazards
  4.4 Hazards generated by dust, fumes and gases
  4.5 Hazards due to electrical energy
  4.6 Hazards due to unexpected start-up
  4.7 Falls from height
5 Safety requirements and/or protective measures
  5.1 General
  5.2 Mechanical hazards
      5.2.1 Access through openings in the agglomerator chamber
      5.2.2 Feed material that is not pre-cut
      5.2.3 Ejection of parts or materials from the agglomerator
            chamber
      5.2.4 Strength
  5.3 Thermal hazards
  5.4 Noise hazards
      5.4.1 Noise reduction at source by design
      5.4.2 Noise reduction by protective measures
      5.4.3 Information connected with noise hazards
  5.5 Hazards generated by dust, fumes and gases
  5.6 Hazards due to electrical energy
      5.6.1 Electrical equipment
      5.6.2 Accumulation of electrostatic charges
  5.7 Unexpected start-up
  5.8 Falls from height
6 Verification of conformity with the safety requirements
  and/or protective measures
7 Information for use
  7.1 Instruction manual
  7.2 Marking
Annex A (normative) Noise test code
  A.1 Scope
  A.2 Determination of sound power levels
      A.2.1 Basic standards
      A.2.2 Measurement uncertainty
  A.3 Determination of emission sound pressure level at the
      workstation(s)
      A.3.1 Basic standards
      A.3.2 Measurement uncertainty
  A.4 Installation and mounting conditions for the noise
      measurement
  A.5 Operating conditions
  A.6 Information to be recorded and reported
      A.6.1 General
      A.6.2 General agglomerator data
      A.6.3 Agglomerator chamber data
      A.6.4 Standards
      A.6.5 Noise data
      A.6.6 Specified test parameters
      A.6.7 Installation and operating conditions
  A.7 Declaration and verification of noise emission values
Annex ZA (informative) Relationship between this European
         Standard and the Essential Requirements of EU
         Directive 98/37/EC
Bibliography

Specifies the essential safety requirements applicable to the design and construction of agglomerators used to densify plastic scrap, reducing its size and/or volume.

DocumentType	Standard
PublisherName	Osterreichisches Normungsinstitut/Austrian Standards
Status	Withdrawn
SupersededBy	ÖNORM EN 12012-4 : 2019 07 15

Standards	Relationship
EN 12012-4:2006+A1:2008	Identical
NS EN 12012-4 : 2006 + A1 2008	Identical
I.S. EN 12012-4:2006	Identical
BS EN 12012-4 : 2006	Identical
SN EN 12012-4 : 2007 + A1 2008	Identical
DIN EN 12012-4:2010-01	Identical
NBN EN 12012-4 : 2006 + A1 2008	Identical
NEN EN 12012-4 : 2006 + A1 2008	Identical
UNI EN 12012-4 : 2008	Identical
NF EN 12012-4 : 2007 + A1 2008	Identical
UNE-EN 12012-4:2007	Identical

ISO 4871:1996	Acoustics — Declaration and verification of noise emission values of machinery and equipment
ISO 14122-3:2016	Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails
ISO 14122-1:2016	Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access
ONORM EN ISO 13857 : 2008	SAFETY OF MACHINERY - SAFETY DISTANCES TO PREVENT HAZARD ZONES BEING REACHED BY UPPER AND LOWER LIMBS
ISO 9614-1:1993	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 1: Measurement at discrete points
ISO 13732-1:2006	Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces
ISO 9614-2:1996	Acoustics — Determination of sound power levels of noise sources using sound intensity — Part 2: Measurement by scanning
ISO 14122-4:2016	Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders
ISO 12100-2:2003	Safety of machinery Basic concepts, general principles for design Part 2: Technical principles
ISO 13857:2008	Safety of machinery Safety distances to prevent hazard zones being reached by upper and lower limbs
ISO 12100-1:2003	Safety of machinery Basic concepts, general principles for design Part 1: Basic terminology, methodology
ISO 14122-2:2016	Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways