• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

ONORM EN 12245 : 2012

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

TRANSPORTABLE GAS CYLINDERS - FULLY WRAPPED COMPOSITE CYLINDERS
Superseded date

27-10-2022

Published date

12-01-2013

Couvre les exigences des matières, la conception minimal Construction, l'essai du prototype et la routine En fabriquant des examens des bouteilles de gaz composées Avec une capacité de l'eau vers le haut à et incluant 450 L afin que Gaz comprimés, se liquéfié et dissous.

Committee
TC 061
DocumentType
Standard
PublisherName
Osterreichisches Normungsinstitut/Austrian Standards
Status
Superseded
SupersededBy

ISO 75-1:2013 Plastics Determination of temperature of deflection under load Part 1: General test method
ISO 8521:2009 Plastics piping systems Glass-reinforced thermosetting plastics (GRP) pipes Test methods for the determination of the apparent initial circumferential tensile strength
ISO 11114-1:2012 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 1: Metallic materials
ONORM EN ISO 11114-1 : OCT 2017 GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 1: METALLIC MATERIALS (ISO 11114-1:2012)
ISO 9809-3:2010 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 3: Normalized steel cylinders
ISO 2884-1:1999 Paints and varnishes — Determination of viscosity using rotary viscometers — Part 1: Cone-and-plate viscometer operated at a high rate of shear
ONORM EN ISO 13769 : 2009 GAS CYLINDERS - STAMP MARKING
ISO 3341:2000 Textile glass Yarns Determination of breaking force and breaking elongation
ISO 13341:2010 Gas cylinders — Fitting of valves to gas cylinders
ISO 11114-3:2010 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 3: Autogenous ignition test for non-metallic materials in oxygen atmosphere
ISO 1628-3:2010 Plastics Determination of the viscosity of polymers in dilute solution using capillary viscometers Part 3: Polyethylenes and polypropylenes
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ONORM EN 13322-1 : 2006 TRANSPORTABLE GAS CYLINDERS - REFILLABLE WELDED STEEL GAS CYLINDERS - DESIGN AND CONSTRUCTION - PART 1: CARBON STEEL
ISO 10618:2004 Carbon fibre — Determination of tensile properties of resin-impregnated yarn
ONORM EN ISO 11114-2 : 2013 GAS CYLINDERS - COMPATIBILITY OF CYLINDER AND VALVE MATERIALS WITH GAS CONTENTS - PART 2: NON-METALLIC MATERIALS (ISO 11114-2:2013)
ISO 11114-2:2013 Gas cylinders Compatibility of cylinder and valve materials with gas contents Part 2: Non-metallic materials
ISO 11120:2015 Gas cylinders Refillable seamless steel tubes of water capacity between 150 l and 3000 l Design, construction and testing
ISO 3146:2000 Plastics — Determination of melting behaviour (melting temperature or melting range) of semi-crystalline polymers by capillary tube and polarizing-microscope methods
ONORM EN ISO 9809-2 : 2010 GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 2: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH GREATER THAN OR EQUAL TO 1100 MPA
ISO 175:2010 Plastics Methods of test for the determination of the effects of immersion in liquid chemicals
ONORM EN ISO 9809-1 : 2010 GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 1: QUENCHED AND TEMPERED STEEL CYLINDERS WITH TENSILE STRENGTH LESS THAN 1100 MPA
ISO 10156:2017 Gas cylinders — Gases and gas mixtures — Determination of fire potential and oxidizing ability for the selection of cylinder valve outlets
ISO 9809-2:2010 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 2: Quenched and tempered steel cylinders with tensile strength greater than or equal to 1 100 MPa
ISO 11114-4:2017 Transportable gas cylinders Compatibility of cylinder and valve materials with gas contents Part 4: Test methods for selecting steels resistant to hydrogen embrittlement
ISO 15512:2016 Plastics Determination of water content
ONORM EN ISO 9809-3 : 2010 GAS CYLINDERS - REFILLABLE SEAMLESS STEEL GAS CYLINDERS - DESIGN, CONSTRUCTION AND TESTING - PART 3: NORMALIZED STEEL CYLINDERS
ISO 14130:1997 Fibre-reinforced plastic composites — Determination of apparent interlaminar shear strength by short-beam method
ISO 75-3:2004 Plastics — Determination of temperature of deflection under load — Part 3: High-strength thermosetting laminates and long-fibre-reinforced plastics
ISO 9809-1:2010 Gas cylinders Refillable seamless steel gas cylinders Design, construction and testing Part 1: Quenched and tempered steel cylinders with tensile strength less than 1 100 MPa
ISO 13769:2007 Gas cylinders Stamp marking
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.