• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

PREN 1254-6 : DRAFT 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 6: FITTING WITH PUSH-FIT ENDS
Superseded date

01-10-2012

Published date

12-01-2013

Foreword
1 Scope
2 Normative references
3 Terms and Definitions
4 Operating temperatures and pressures
5 Requirements
6 Testing, assessment and sampling methods
7 Evaluation of conformity
8 Classification and designation
9 Marking
Annex A (normative) - Method for testing leaktightness
        of joints with metallic tube under internal
        hydrostatic pressure
Annex B (normative) - Method for testing resistance to
        pull-out of joints with metallic tube
Annex C (normative) - Test method for resistance of
        joints with metallic tube to temperature cycling
Annex D (normative) - Method for testing the resistance
        of joints with metallic tube to pressure
        cycling
Annex E (normative) - Test method for leaktightness
        of joints with metallic tube under vacuum
Annex F (normative) - Test method for the resistance
        of joints with metallic tube to vibration
Annex G (normative) - Test method for leaktightness
        of joints with metallic tube under internal
        hydrostatic pressure while subjected to
        bending
Annex H (normative) - Test method for disconnection
        and re-use
Annex I (normative) - Fitting rotation test
Annex J (normative) - Determination of resistance to
        stress corrosion
Annex K (normative) - Pressure test for fittings bodies
        with as-cast microstructure or fabricated by
        welding or brazing
Annex L (normative) - Determination of mean depth
        of dezincification
Bibliography

Describes materials and test requirements for fittings of copper and copper alloys.

Committee
TC 133
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
11/30213587 DC : 0 Identical
04/30095586 DC : 0 Identical

PREN 13618 : DRAFT 2009 FLEXIBLE HOSE ASSEMBLIES IN DRINKING WATER INSTALLATIONS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
09/30198696 DC : 0 BS EN 13618 - FLEXIBLE HOSE ASSEMBLIES IN DRINKING WATER INSTALLATIONS - FUNCTIONAL REQUIREMENTS AND TEST METHODS
07/30163621 DC : 0 BS EN 1254-5 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 5: FITTINGS WITH SHORT ENDS FOR CAPILLARY BRAZING TO COPPER TUBES
07/30163615 DC : 0 BS EN 1254-1 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 1: FITTINGS WITH ENDS FOR CAPILLARY SOLDERING OR CAPILLARY BRAZING TO COPPER TUBES
07/30163618 DC : 0 BS EN 1254-2 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 2: FITTINGS WITH COMPRESSION ENDS FOR USE WITH COPPER TUBES
07/30144895 DC : 0 BS EN 723 - COPPER AND COPPER ALLOYS - COMBUSTION METHOD FOR DETERMINATION OF CARBON CONTENT ON THE INNER SURFACE OF COPPER TUBES OR FITTINGS
04/30114458 DC : 0 EN 14905 - COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - RECOMMENDED PRACTICE FOR THE INSTALLATION OF COPPER AND COPPER ALLOY PLUMBING FITTINGS

EN 1655:1997 Copper and copper alloys - Declarations of conformity
EN ISO 15875-2:2003/A1:2007 PLASTICS PIPING SYSTEMS FOR HOT AND COLD WATER INSTALLATIONS - CROSSLINKED POLYETHYLENE (PE-X) - PART 2: PIPES
EN 1254-4:1998/AC:1999 COPPER AND COPPER ALLOYS - PLUMBING FITTINGS - PART 4: FITTINGS COMBINING OTHER END CONNECTIONS WITH CAPILLARY OR COMPRESSION ENDS
EN 12293:1999 Plastics piping systems - Thermoplastics pipes and fittings for hot and cold water - Test method for the resistance of mounted assemblies to temperature cycling
EN 681-1:1996/A3:2005 ELASTOMERIC SEALS - MATERIALS REQUIREMENTS FOR PIPE JOINT SEALS USED IN WATER AND DRAINAGE APPLICATIONS - PART 1: VULCANIZED RUBBER
EN ISO 15874-5:2013 Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 5: Fitness for purpose of the system (ISO 15874-5:2013)
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN ISO 15876-2:2017 Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 2: Pipes (ISO 15876-2:2017)
ISO 15875-5:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system
ISO 15875-2:2003 Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes
EN ISO 15876-5:2017 Plastics piping systems for hot and cold water installations - Polybutene (PB) - Part 5: Fitness for purpose of the system (ISO 15876-5:2017)
EN ISO 21003-2:2008/A1:2011 Multilayer piping systems for hot and cold water installations inside buildings - Part 2: Pipes - Amendment 1 (ISO 21003-2:2008/Amd 1:2011)
EN 12449:2016 Copper and copper alloys - Seamless, round tubes for general purposes
EN 713:1993 Plastics piping systems - Mechanical joints between fittings and polyolefin pressure pipes - Test method for leaktightness under internal pressure of assemblies subjected to bending
EN ISO 15875-5:2003 Plastics piping systems for hot and cold water installations - Crosslinked polyethylene (PE-X) - Part 5: Fitness for purpose of the system (ISO 15875-5:2003)
EN ISO 9001:2015 Quality management systems - Requirements (ISO 9001:2015)
ISO 21003-2:2008 Multilayer piping systems for hot and cold water installations inside buildings — Part 2: Pipes
ISO 6509:1981 Corrosion of metals and alloys Determination of dezincification resistance of brass
ISO 15876-2:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes
ISO 9001:2015 Quality management systems — Requirements
EN 12164:2016 Copper and copper alloys - Rod for free machining purposes
EN 12295:1999 Plastics piping systems - Thermoplastics pipes and associated fittings for hot and cold water - Test method for resistance of joints to pressure cycling
ISO 9924-1:2016 Rubber and rubber products — Determination of the composition of vulcanizates and uncured compounds by thermogravimetry — Part 1: Butadiene, ethylene-propylene copolymer and terpolymer, isobutene-isoprene, isoprene and styrene-butadiene rubbers
EN ISO 21003-5:2008 Multilayer piping systems for hot and cold water installations inside buildings - Part 5: Fitness for purpose of the system (ISO 21003-5:2008)
EN 12294:1999 Plastics piping systems - Systems for hot and cold water - Test method for leaktightness under vacuum
EN ISO 15874-2:2013 Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2: Pipes (ISO 15874-2:2013)
EN ISO 6509 : 1995 CORROSION OF METALS AND ALLOYS - DETERMINATION OF DEZINCIFICATION RESISTANCE OF BRASS
EN 12165:2016 COPPER AND COPPER ALLOYS - WROUGHT AND UNWROUGHT FORGING STOCK
ISO 15876-5:2017 Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system
EN 1982:2017 Copper and copper alloys - Ingots and castings
ISO 6957:1988 Copper alloys Ammonia test for stress corrosion resistance
EN 712:1993 Thermoplastics piping systems - End-load bearing mechanical joints between pressure pipes and fittings - Test method for resistance to pull-out under constant longitudinal force

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.