• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

PREN 1287 : DRAFT 2015

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

SANITARY TAPWARE - LOW PRESSURE THERMOSTATIC MIXING VALVES - GENERAL TECHNICAL SPECIFICATION
Superseded date

01-08-2017

Published date

19-06-2013

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and units
5 Classification, designation
6 Designation
7 Marking/Identification
8 Materials
9 Dimensional characteristics
10 Backflow protection
11 Test sequence
12 Leaktightness
13 Performance
14 Pressure Resistance
15 Torsional resistance of the operating controls
16 Mechanical endurance characteristics
Annex A (normative) - Test Set-up Descriptions
Annex B (normative) - Measurements
Annex C (informative) - Temperature transit
Annex D (normative)
Bibliography

Defines general construction, performance and material requirements for PN 10 thermostatic mixing valves (TMV) and includes test methods for the verification of mixed water temperature performance at the point of use below 45 degrees C.

Committee
TC 164
DocumentType
Draft
PublisherName
Comite Europeen de Normalisation
Status
Superseded
SupersededBy

Standards Relationship
15/30321799 DC : 0 Identical
13/30280715 DC : 0 Identical

PD 6504:1983 Medical information on human reaction to skin contact with hot surfaces
EN 13202 : 2000 ERGONOMICS OF THE THERMAL ENVIRONMENT - TEMPERATURES OF TOUCHABLE HOT SURFACES - GUIDANCE FOR ESTABLISHING SURFACE TEMPERATURE LIMIT VALUES IN PRODUCT STANDARDS WITH THE AID OF EN 563
EN 246:2003 Sanitary tapware - General specifications for flow rate regulators
EN 1112:2008 Sanitary tapware - Shower outlets for sanitary tapware for water supply systems of type 1 and type 2 - General technical specification
EN 1057:2006+A1:2010 Copper and copper alloys - Seamless, round copper tubes for water and gas in sanitary and heating applications
EN 13618:2016 Flexible hose assemblies in drinking water installations - Functional requirements and test methods
EN 1113:2015 SANITARY TAPWARE - SHOWER HOSES FOR SANITARY TAPWARE FOR WATER SUPPLY SYSTEMS OF TYPE 1 AND TYPE 2 - GENERAL TECHNICAL SPECIFICATION
EN 1717:2000 Protection against pollution of potable water in water installations and general requirements of devices to prevent pollution by backflow
EN 563:1994/A1:1999/AC:2000 SAFETY OF MACHINERY - TEMPERATURES OF TOUCHABLE SURFACES - ERGONOMICS DATA TO ESTABLISH TEMPERATURE LIMIT VALUES FOR HOT SURFACES
EN ISO 228-1:2003 Pipe threads where pressure-tight joints are not made on the threads - Part 1: Dimensions, tolerances and designation (ISO 228-1:2000)
ISA MC96.1 : 1982 TEMPERATURE MEASUREMENT THERMOCOUPLES
EN ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full - Part 1: General principles and requirements (ISO 5167-1:2003)
ISO 5167-1:2003 Measurement of fluid flow by means of pressure differential devices inserted in circular cross-section conduits running full Part 1: General principles and requirements
EN 13959:2004 Anti-pollution check valves - DN 6 to DN 250 inclusive family E, type A, B, C and D
EN 200:2008 Sanitary tapware - Single taps and combination taps for water supply systems of type 1 and type 2 - General technical specification
ISO 9886:2004 Ergonomics Evaluation of thermal strain by physiological measurements
ISO 228-1:2000 Pipe threads where pressure-tight joints are not made on the threads Part 1: Dimensions, tolerances and designation
EN 248:2002 Sanitary tapware - General specification for electrodeposited coatings of Ni-Cr

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.