• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

PREN 9138 : 200P1

Withdrawn
Withdrawn

A Withdrawn Standard is one, which is removed from sale, and its unique number can no longer be used. The Standard can be withdrawn and not replaced, or it can be withdrawn and replaced by a Standard with a different number.

AEROSPACE SERIES - QUALITY MANAGEMENT SYSTEMS - STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS
Withdrawn date

18-02-2018

Introduction
1 Scope
2 References
3 Terms and definitions
4 General requirements
5 Required information to be documented
6 Requirements for accepting product by individual lots
7 Requirements for accepting product under switching rules
8 Requirements for accepting product produced under process
  controls
9 Additional requirements for accepting products based on
  continuous sampling, skip-lot sampling, or methods
  for special cases
Annex A (informative) - Guidelines for assigning Initial
        Reliability Requirement quality levels
Annex B (informative) - Acronym log
Annex C (informative) - Mathematics for accepting product
        under lot-by-lot inspection
Annex D (informative) - Guidelines and recommendations
        for successful implementation of statistical
        product acceptance methods
Annex E (informative) - Discussion on the technical rationale
        and history of the relationship of quality parameters
        to reliability
Annex F (informative) - Guidelines for choosing a statistical
        product acceptance technique and quality parameter
Annex G (informative) - Guidelines and recommendations
        for accepting product by individual lots
Annex H (informative) - Guidelines for some special
        acceptance methods
Annex I (informative) - Guidelines and recommendations
        for accepting product produced under switching
        rules
Annex J (informative) - Guidelines and recommendations
        for accepting product produced under process
        controls
Annex K (informative) - Guidelines and recommendations
        for accepting product based on continuous
        sampling

Sets up requirements when implementing statistical product acceptance methods to meet defined risk requirements.

DocumentType
Draft
PublisherName
Aerospace & Defence Industries Association of Europe
Status
Withdrawn

EN 9100:2009 Quality Management Systems - Requirements for Aviation, Space and Defense Organizations
ISO 3951-1:2013 Sampling procedures for inspection by variables — Part 1: Specification for single sampling plans indexed by acceptance quality limit (AQL) for lot-by-lot inspection for a single quality characteristic and a single AQL
SAE ARP 9013/2 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING ATTRIBUTE OR VARIABLE LOT ACCEPTANCE SAMPLING PLANS
SAE ARP 5580 : 2012 RECOMMENDED FAILURE MODES AND EFFECTS ANALYSIS (FMEA) PRACTICES FOR NON-AUTOMOBILE APPLICATIONS
ISO 2859-3:2005 Sampling procedures for inspection by attributes — Part 3: Skip-lot sampling procedures
MIL-HDBK-1823 Revision A:2009 NONDESTRUCTIVE EVALUATION SYSTEM, RELIABILITY ASSESSMENT
FAA AC 21-43 : 2015 PRODUCTION UNDER 14 CFR PART 21, SUBPARTS F, G, K, AND O
ISO 11462-2:2010 Guidelines for implementation of statistical process control (SPC) — Part 2: Catalogue of tools and techniques
EN 9110:2015 Quality Management Systems - Requirements for Aviation Maintenance Organizations
ISO/IEC Guide 98-1:2009 Uncertainty of measurement — Part 1: Introduction to the expression of uncertainty in measurement
MIL-STD-1235 Revision C:1988 SINGLE AND MULTILEVEL CONTINUOUS SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES FUNCTIONAL CURVES OF THE CONTINUOUS SAMPLING PLANS
ISO/IEC Guide 98-4:2012 Uncertainty of measurement Part 4: Role of measurement uncertainty in conformity assessment
ISO 10576-1:2003 Statistical methods — Guidelines for the evaluation of conformity with specified requirements — Part 1: General principles
MIL-STD-414 Base Document:1957 SAMPLING PROCEDURE AND TABLE FOR INSPECTION BY VARIABLES FOR PERCENT DEFECTIVE
SAE ARP 4761 : 1996 GUIDELINES AND METHODS FOR CONDUCTION THE SAFETY ASSESSMENT PROCESS ON CIVIL AIRBORNE SYSTEMS AND EQUIPMENT
SAC GB/T 2828-3 : 2008 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 3: SKIP-LOT SAMPLING PROCEDURES
ASQ B1/B2/B3:1996 Guide For Quality Control Charts - Control Chart Method Of Analyzing Data - Control Chart Method Of Controlling Quality During Production
SAE ARP 9013/4 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING CONTINUOUS SAMPLING, SKIP-LOT SAMPLING, OR METHODS FOR SPECIAL CASES
SAE J 1739 : 2009 POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN DESIGN (DESIGN FMEA), POTENTIAL FAILURE MODE AND EFFECTS ANALYSIS IN MANUFACTURING AND ASSEMBLY PROCESSES (PROCESS FMEA)
SAE ARP 9013/1 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING ISOLATED LOT SAMPLING METHODS
SAE ARP 9013/3 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS USING PROCESS CONTROL METHODS
ISO 9000:2015 Quality management systems — Fundamentals and vocabulary
ISO 11462-1:2001 Guidelines for implementation of statistical process control (SPC) Part 1: Elements of SPC
SAC GB/T 6378-1 : 2008 SAMPLING PROCEDURES FOR INSPECTION BY VARIABLES - PART 1: SPECIFICATION FOR SINGLE SAMPLING PLANS INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION FOR A SINGLE QUALITY CHARACTERISTIC AND A SINGLE AQL
MIL-STD-105 Revision E:1989 SAMPLING PROCEDURES AND TABLES FOR INSPECTION BY ATTRIBUTES
SAC GB/T 2828-1 : 2012 SAMPLING PROCEDURES FOR INSPECTION BY ATTRIBUTES - PART 1: SAMPLING SCHEMES INDEXED BY ACCEPTANCE QUALITY LIMIT (AQL) FOR LOT-BY-LOT INSPECTION
SAE ARP 9013 : 2005 STATISTICAL PRODUCT ACCEPTANCE REQUIREMENTS
EN 9120:2010 Quality Management Systems - Requirements for Aviation, Space and Defence Distributors
ASQ Z1.9:2003 (R2013) Sampling Procedures And Tables For Inspection By Variables For Percent Nonconforming
ISO/IEC Guide 98-3:2008 Uncertainty of measurement — Part 3: Guide to the expression of uncertainty in measurement (GUM:1995)

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.