PREN ISO 13856-2 : DRAFT 2011

Superseded

Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Add to Watchlist

View superseded by

This Standard has been added successfully to your Watchlist.
Please visit My Watchlist to see all standards that you are watching.

Please log in or create an account to add this standard to your Watchlist.

We could not add this standard to your Watchlist.
Please retry or contact support for assistance.

You need to be logged in to add this standard to your Watchlist.
Please log in now or create an account to add.

You already added this Product in the Watchlist.

SAFETY OF MACHINERY - PRESSURE-SENSITIVE PROTECTIVE DEVICES - PART 2: GENERAL PRINCIPLES FOR THE DESIGN AND TESTING OF PRESSURESENSITIVE EDGES AND PRESSURE-SENSITIVE BARS (ISO/DIS 13856-2:2011)

Available format(s):

Superseded date: 01-04-2013

Language(s):

Published date: 12-01-2013

Publisher: Comite Europeen de Normalisation

Add to Watchlist

Pure ENs are not available for sale, please purchase a suitable national adoption

Table of Contents - (Show below) - (Hide below)

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Requirements
5 Marking
6 Information for selection and use
7 Verification of requirements
Annex A (normative) - Timing diagrams for
        pressure-sensitive edges and pressure-sensitive
        bars with and without reset
Annex B (informative) - Operating speed, force
        and travel - Explanatory remarks and
        recommendations
Annex C (informative) - Device selection guidance
        for the machinery manufacturer/user
Annex D (informative) - Design guidance
Annex E (informative) - Application guidance
Annex F (informative) - Guidance on installation,
        commissioning and testing
Annex G (informative) - General considerations for
        systems meeting category 2 according to
        ISO 13849-1
Annex ZA (informative) - Relationship between this
         European Standard and the Essential
         Requirements of EU Directive 2006/42/EC
Bibliography

Abstract - (Show below) - (Hide below)

Defines general principles and describes requirements for the design and testing of pressure-sensitive edges and pressure-sensitive bars used as safeguards and not as actuating devices for normal operation.

General Product Information - (Show below) - (Hide below)

Comment Closes On
Committee	TC 114
Document Type	Draft
ISBN
Pages
Published
Publisher	Comite Europeen de Normalisation
Status	Superseded
Superseded By	EN ISO 13856-2:2013

National Adoptions - (Show below) - (Hide below)

Equivalent Standard(s)	Relationship
11/30239643 DC : 0	Identical

Standards Referencing This Book - (Show below) - (Hide below)

ISO 14119:2013	Safety of machinery Interlocking devices associated with guards Principles for design and selection
IEC 61000-4-4 : 3.0EN+(REDLINE+VERSION)	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-4: TESTING AND MEASUREMENT TECHNIQUES - ELECTRICAL FAST TRANSIENT/BURST IMMUNITY TEST
IEC 60068-2-27:2008	Environmental testing - Part 2-27: Tests - Test Ea and guidance: Shock
ISO 14120:2015	Safety of machinery Guards General requirements for the design and construction of fixed and movable guards
ISO 4413:2010	Hydraulic fluid power General rules and safety requirements for systems and their components
IEC 60204-1:2016	Safety of machinery - Electrical equipment of machines - Part 1: General requirements
IEC 60947-5-1 : 4.0	LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES
ISO 12100:2010	Safety of machinery General principles for design Risk assessment and risk reduction
IEC 61000-4-6 : 4.0	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 4-6: TESTING AND MEASUREMENT TECHNIQUES - IMMUNITY TO CONDUCTED DISTURBANCES, INDUCED BY RADIO-FREQUENCY FIELDS
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV	Degrees of protection provided by enclosures (IP Code)
IEC 61496-3:2008	Safety of machinery - Electro-sensitive protective equipment - Part 3: Particular requirements for Active Opto-electronic Protective Devices responsive to Diffuse Reflection (AOPDDR)
IEC 61000-4-2:2008	Electromagnetic compatibility (EMC) - Part 4-2: Testing and measurement techniques - Electrostatic discharge immunity test
IEC 61000-4-3:2006+AMD1:2007+AMD2:2010 CSV	Electromagnetic compatibility (EMC) - Part 4-3: Testing and measurement techniques - Radiated, radio-frequency, electromagnetic field immunity test
ISO 13849-2:2012	Safety of machinery — Safety-related parts of control systems — Part 2: Validation
IEC 61496-1:2012	Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests
ISO 4414:2010	Pneumatic fluid power General rules and safety requirements for systems and their components
IEC 61439-1:2011	Low-voltage switchgear and controlgear assemblies - Part 1: General rules
IEC 60068-2-14:2009	Environmental testing - Part 2-14: Tests - Test N: Change of temperature
ISO 13849-1:2015	Safety of machinery Safety-related parts of control systems Part 1: General principles for design
IEC 61000-6-2 : 3.0:2016	ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS
IEC 60664-1:2007	Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests
IEC 61496-2:2013	Safety of machinery - Electro-sensitive protective equipment - Part 2: Particular requirements for equipment using active opto-electronic protective devices (AOPDs)

Categories associated with this Standard - (Show below) - (Hide below)

Sub-Categories associated with this Standard - (Show below) - (Hide below)

Sorry this product is not available in your region.

Add To Cart