Skip to content
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Go to AMERICAS site X
Please enter a keyword to search

  • SAE AMS 3058 : 2013

    View superseded by
    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    View superseded by
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    GREASE: WIDE TEMPERATURE RANGE LITHIUM OR LITHIUM COMPLEX THICKENED FOR AIRCRAFT WHEEL BEARINGS

    Available format(s):  Hardcopy, PDF

    Superseded date:  09-08-2018

    Language(s):  English

    Published date:  28-03-2013

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALIFICATION
    5. QUALITY ASSURANCE PROVISIONS
    6. PREPARATION FOR DELIVERY
    7. ACKNOWLEDGMENT
    8. REJECTIONS
    9. NOTES
    APPENDIX A

    Abstract - (Show below) - (Hide below)

    Specifies grease for use on aircraft wheel bearings.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-M
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By

    Standards Referencing This Book - (Show below) - (Hide below)

    IP 71 : 1995 SECTION 1: PETROLEUM PRODUCTS - TRANSPARENT AND OPAQUE LIQUIDS - DETERMINATION OF KINEMATIC VISCOSITY AND CALCULATION OF DYNAMIC VISCOSITY - SECTION 2: GLASS CAPILLARY KINEMATIC VISCOMETERS - SPECIFICATIONS AND OPERATING INSTRUCTIONS (TWO PART SET)
    ASTM D 566 : 2017 : REDLINE Standard Test Method for Dropping Point of Lubricating Grease
    DEFSTAN 05-50(PT62)/1(1995) : 1995 METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 62: LOW TEMPERATURE TORQUE OF GREASES CONTAMINATED WITH WATER
    ASTM D 5706 : 2016 : REDLINE Standard Test Method for Determining Extreme Pressure Properties of Lubricating Greases Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
    IP 132 : 96(R2004) PETROLEUM PRODUCTS - LUBRICATING GREASE - DETERMINATION OF DROPPING POINT
    ASTM D 942 : 2015 : REDLINE Standard Test Method for Oxidation Stability of Lubricating Greases by the Oxygen Pressure Vessel Method
    ISO 2160:1998 Petroleum products Corrosiveness to copper Copper strip test
    ASTM D 6184 : 2017 : REDLINE Standard Test Method for Oil Separation from Lubricating Grease (Conical Sieve Method)
    DEFSTAN 05-50(PT9)/1(1986) : 1986 METHODS FOR TESTING FUELS, LUBRICANTS AND ASSOCIATED PRODUCTS - PART 9: SEPARATION OF OIL FROM GREASE
    SAE AMS 4640 : 2011 ALUMINUM BRONZE, BARS, RODS, SHAPES, TUBES, AND FORGINGS, 81.5CU - 10.0AL - 4.8NI - 3.0FE, DRAWN AND STRESS RELIEVED (HR50) OR TEMPER ANNEALED (TQ50)
    ASTM D 5707 : 2016 : REDLINE Standard Test Method for Measuring Friction and Wear Properties of Lubricating Grease Using a High-Frequency, Linear-Oscillation (SRV) Test Machine
    ASTM D 217 : 2017 : REDLINE TEST METHODS FOR CONE PENETRATION OF LUBRICATING GREASE
    ASTM D 4048 : 2017-01 TEST METHOD FOR DETECTION OF COPPER CORROSION FROM LUBRICATING GREASE
    ASTM D 4289 : 2014-02 TEST METHOD FOR ELASTOMER COMPATIBILITY OF LUBRICATING GREASES AND FLUIDS
    SAE AMS 3217/2 : 2012 TEST SLABS, ACRYLONITRILE BUTADIENE (NBR-L), LOW ACRYLONITRILE, 65-75
    ASTM D 2595 : 2017 Standard Test Method for Evaporation Loss of Lubricating Greases Over Wide-Temperature Range
    FED-STD-791 Revision D:2007 TESTING METHOD OF LUBRICANTS, LIQUID FUELS, AND RELATED PRODUCTS
    ISO 2176:1995 Petroleum products — Lubricating grease — Determination of dropping point
    ASTM D 2265 : 2015-05 TEST METHOD FOR DROPPING POINT OF LUBRICATING GREASE OVER WIDE TEMPERATURE RANGE
    View more information

    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective