We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • SAE AMS 5516 : 2012

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    STEEL, CORROSION-RESISTANT, SHEET, STRIP, AND PLATE, 18CR - 9.0NI (SAE 30302), SOLUTION HEAT TREATED

    Available format(s):  Hardcopy, PDF

    Superseded date:  11-03-2019

    Language(s):  English

    Published date:  01-01-2012

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. TECHNICAL REQUIREMENTS
    4. QUALITY ASSURANCE PROVISIONS
    5. PREPARATION FOR DELIVERY
    6. ACKNOWLEDGMENT
    7. REJECTIONS
    8. NOTES

    Abstract - (Show below) - (Hide below)

    Covers a corrosion-resistant steel in the form of sheet, strip, and plate.

    General Product Information - (Show below) - (Hide below)

    Committee AMS-F
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE AS 27197 : 2014 SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, SILICONE RUBBER, AMS7268
    MIL DTL 8783 : D CLAMP, HOSE, FLAT BAND 500 DEGREES F, GENERAL SPECIFICATION FOR
    SAE AMS 3281 : 2016 SEALING COMPOUND, POLYSULFIDE (T) SYNTHETIC RUBBER FOR INTEGRAL FUEL TANK AND FUEL CELL CAVITIES LOW DENSITY FOR INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
    MIL DTL 22499 : D SHIM STOCK, LAMINATED
    SAE AMS 3276 : 2016 SEALING COMPOUND, INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
    SAE AMS 3102 : 2017 SEALING COMPOUND, POLYTHIOETHER RUBBER FAST CURING, LIGHT WEIGHT (SPECIFIC GRAVITY 0.78, MAX.) FOR INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
    SAE AS 269J:2012:(S2018) IDENTIFICATION OF MATERIAL FOR AN, MS AND AS ENGINE AND PROPELLER STANDARD UTILITY PARTS AND ALSO FOR COMPANY PARTS
    SAE AMS 3265 : 2015 SEALING COMPOUND, POLYSULFIDE (T) RUBBER, FUEL RESISTANT, NON-CHROMATED CORROSION INHIBITING, FOR INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
    MIL DTL 24127 : A EDUCTORS, GASOLINE, OIL, OR WATER
    SAE AS 5127 : 2013 AEROSPACE STANDARD TEST METHODS FOR AEROSPACE SEALANTS METHODS FOR PREPARING AEROSPACE SEALANT TEST SPECIMENS
    SAE AS 4751 : 2005 COUPLING ASSEMBLY, V-BAND SHEET METAL WIDE FLANGE, PNEUMATIC TUBE
    SAE AMS 3263 : 1997 SEALING COMPOUND, POLYTHIOETHER, AMBIENT CURE OR IMMEDIATE HEAT CURE FOR AIRCRAFT STRUCTURES, FUEL RESISTANT WITH INTERMITTENT USE TO 400 MDCF (204 MDCC)
    MIL DTL 21567 : B COMPOUND, SILICONE, SOFT FILM
    SAE AS 27196 : 2014 SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROCARBON RUBBER, AMS7276
    SAE AS 27198 : 2014 SEAL, BONDED, 302 CORROSION RESISTANT STEEL, AMS5516, MOLD IN GROOVE, FLUOROSILICONE RUBBER, MIL-DTL-25988
    SAE AMS S 8802 : 2015 SEALING COMPOUND, FUEL RESISTANT, INTEGRAL FUEL TANKS AND FUEL CELL CAVITIES
    SAE AMS 3278 : 2016 SEALING AND COATING COMPOUND, POLYURETHANE (PUR), FUEL RESISTANT, HIGH TENSILE STRENGTH/ELONGATION, FOR INTEGRAL FUEL TANKS/FUEL CAVITIES/GENERAL PURPOSE
    SAE AMS 3277 : 2015 SEALING COMPOUND, POLYTHIOETHER RUBBER, FAST CURING FOR INTEGRAL FUEL TANKS AND GENERAL PURPOSE, INTERMITTENT USE TO 360 DEGREES F (182 DEGREES C)
    SAE AMS 3284 : 2017 SEALING COMPOUND, LOW ADHESION, FOR REMOVABLE PANELS AND FUEL TANK INSPECTION PLATES
    SAE AMS DTL 22499 : 2013 SHIM STOCK, LAMINATED
    SAE AMS 3259 : 1997 SEALING COMPOUND, POLYTHIOETHER - NONCHROMATED, CORROSION INHIBITING FOR INTERMITTENT USE TO 360 DEGREE F (182 DEGREE C)

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AMS 2248 : 2016 CHEMICAL CHECK ANALYSIS LIMITS, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, MARAGING AND OTHER HIGHLY-ALLOYED STEELS, AND IRON ALLOYS
    SAE AMS 2371 : 2016 QUALITY ASSURANCE SAMPLING AND TESTING, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, WROUGHT PRODUCTS AND FORGING STOCK
    ASTM E 353 : 2014 : REDLINE Standard Test Methods for Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys
    SAE AS 4194 : 2012 SHEET AND STRIP, SURFACE FINISH NOMENCLATURE
    SAE AMS 2807B : 2012 IDENTIFICATION, CARBON AND LOW-ALLOY STEELS, CORROSION AND HEAT-RESISTANT STEELS AND ALLOYS, SHEET, STRIP, PLATE, AND AIRCRAFT TUBING
    SAE AMS 2242 : 2014 TOLERANCES, CORROSION AND HEAT RESISTANT STEEL, IRON ALLOY, TITANIUM, AND TITANIUM ALLOY SHEET, STRIP, AND PLATE
    ASTM E 290 : 2014 : REDLINE Standard Test Methods for Bend Testing of Material for Ductility
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective