We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • SAE AMS DTL 23053 : 1999

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR

    Available format(s): 

    Superseded date:  16-10-2016

    Language(s): 

    Published date:  01-01-1999

    Publisher:  SAE International

    Add to Watchlist

    Sorry this product is not available in your region.

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. APPLICABLE DOCUMENTS
    3. REQUIREMENTS
    4. VERIFICATION
    5. PACKAGING
    6. NOTES

    Abstract - (Show below) - (Hide below)

    Determines the requirements for various kinds and colors of electrical insulating sleeving which will shrink to a predetermined size upon applying heat.Includes provisions for demonstration of compliance with requirements through in process inspection and statistical process control. Continuous operating temperatures are in the range -80 deg to +250 deg C (-112 deg to + 482 deg F).

    General Product Information - (Show below) - (Hide below)

    Committee FSC 5970
    Development Note Supersedes MIL DTL 23053 (08/1999)
    Document Type Standard
    Publisher SAE International
    Status Superseded
    Superseded By

    Standards Referenced By This Book - (Show below) - (Hide below)

    BS EN 6049-009 : 2016 AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE, POST INSTALLATION, OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
    MIL PRF 32517 : 0 SPLICE, CONDUCTOR, ELECTRICAL, COAXIAL CABLE, MATCHED IMPEDANCE, GENERAL SPECIFICATION FOR
    MIL DTL 2726/49 : F RECEPTACLE, OUTLET, TRIPLE, ELECTRICAL, 40 - AMPERE, 450 - VOLT, 60 HERTZ, ALTERNATING CURRENT, 4 - POLE, PORTABLE, PLASTIC GROUNDED (SYMBOL NOS. 765.6, 765.7 AND 765.8)
    PREN 6049-009 : 200P3 AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE POST INSTALLATION OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
    MIL HDBK 522 : A GUIDELINES FOR INSPECTION OF AIRCRAFT ELECTRICAL WIRING INTERCONNECT SYSTEMS
    12/30275061 DC : 0 BS EN 6049-009 - AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTIVE SLEEVE IN ARAMID FIBRES - PART 009: SELF WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE POST INSTALLATION OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
    SAE AS 50881 : 2015 WIRING AEROSPACE VEHICLE
    MIL PRF 39006 : G CAPACITOR, FIXED, ELECTROLYTIC (NONSOLID ELECTROLYTE), TANTALUM, ESTABLISHED RELIABILITY, GENERAL SPECIFICATION FOR
    PD ISO/TR 21891:2017 Aerospace electrical requirements. Sleeves and moulded shapes. Specifications for aircraft use
    MIL STD 2042/5 : C FIBER OPTIC CABLE TOPOLOGY INSTALLATION STANDARD METHODS FOR SURFACE SHIPS AND SUBMARINES (CONNECTORS AND INTERCONNECTIONS) (PART 5 OF 7 PARTS)
    SAE AS 5258 : 2012 INSULATING COMPONENT, MOLDED, ELECTRICAL, HEAT SHRINKABLE, CONNECTOR AND CABLE ACCESSORY, SEALING STRAIN RELIEF, GENERAL SPECIFICATION FOR
    MIL DTL 15024/8 : A PLATE, TAGS AND BANDS, BAND IDENTIFICATION, CABLE ASSEMBLY, TYPE K2, HEAT SHRINKABLE TUBING
    SAE AS 6224 : 2015 WRAP-AROUND INSULATION REPAIR AND PROTECTION SLEEVE, PERMANENT, ELECTRIC, ENVIRONMENT RESISTANT
    SAE ARP 4945 : 2013 AEROSPACE-SOLENOID VALVE, HYDRAULIC, THREE WAY, TWO POSITION, DIRECT ACTING
    I.S. EN 6049-009:2016 AEROSPACE SERIES - ELECTRICAL CABLES, INSTALLATION - PROTECTION SLEEVE IN META-ARAMID FIBRES - PART 009: SELF-WRAPPING FIRE PROTECTION SLEEVE, FLEXIBLE, POST INSTALLATION, OPERATING TEMPERATURE FROM -55 DEGREES C TO 260 DEGREES C - PRODUCT STANDARD
    SAE AS 95234 : 2014 CONNECTORS, ELECTRICAL, REVERSE BAYONET, GENERAL SPECIFICATION FOR
    SAE AS 95234A : 2020 CONNECTORS, ELECTRICAL, REVERSE BAYONET, GENERAL SPECIFICATION FOR
    NASA KSC E 165 : 2009 ELECTRICAL GROUND SUPPORT EQUIPMENT FABRICATION, SPECIFICATION FOR
    NASA KSC GP 864 VOL 2A : 2009 ELECTRICAL GROUND SUPPORT EQUIPMENT CABLE HANDBOOK
    NASA KSC STD 132 : 2008 POTTING AND MOLDING ELECTRICAL CABLE ASSEMBLY TERMINATIONS, STANDARD FOR
    EN 6049-009 : 2016 Aerospace series - Electrical cables, installation - Protection sleeve in meta-aramid fibres - Part 009: Self-wrapping fire protection sleeve, flexible, post installation, operating temperature from -55 °C to 260 °C - Product standard

    Standards Referencing This Book - (Show below) - (Hide below)

    MIL DTL 23053/8 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYLIDENE FLUORIDE, SEMI-RIGID, CROSSLINKED
    MIL L 7808 : K (1) LUBRICATING OIL, AIRCRAFT TURBINE ENGINE, SYNTHETIC BASE
    FED STD 228 : A TEST METHODS FOR CABLES AND WIRE, INSULATED
    MIL I 23053/3 : A INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYL CHLORIDE, SEMI RIGID, CROSSLINKED AND NON CROSSLINKED
    MIL DTL 23053/14 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, ETHYLENE-TETRAFLUOROETHYLENE FLUOROPOLYMER, SEMI-RIGID
    MIL DTL 23053/17 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLAME RETARDED, MODIFIED POLYOLEFIN, FLEXIBLE, CROSSLINKED
    MIL DTL 23053/10 : D INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, SILICONE RUBBER, FLEXIBLE
    MIL DTL 23053/18 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, MODIFIED FLUOROPOLYMER, CROSSLINKED
    MIL DTL 23053/7 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYETHYLENE TEREPHTHALATE, NON-CROSSLINKED
    ASTM G 21 : 2015 : REDLINE Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi
    MIL L 23699 : E LUBRICATING OIL, AIRCRAFT TURBINE ENGINES, SYNTHETIC BASE
    A A 694 : E SODIUM CHLORIDE, TECHNICAL
    MIL DTL 23053/13 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUOROELASTOMER FLEXIBLE
    MIL T 5624 : R TURBINE FUEL, AVIATION, GRADES JP 4 AND JP 5
    MIL DTL 23053/15 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, HEAVY-WALL, COATED, FLEXIBLE, OUTER WALL CROSSLINKED
    ASTM D 792 : 2013 : REDLINE Standard Test Methods for Density and Specific Gravity (Relative Density) of Plastics by Displacement
    MIL I 23053/2 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYVINYL CHLORIDE, FLEXIBLE, CROSSLINKED AND NON CROSSLINKED
    MIL I 23053/9 : LATEST INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUOROSILICONE RUBBER, FLEXIBLE
    MIL DTL 23053/16 : B INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED, ELASTOMERIC POLYOLEFIN, FLEXIBLE
    ASTM D 149 : 2009 TEST METHOD FOR DIELECTRIC BREAKDOWN VOLTAGE AND DIELECTRIC STRENGTH OF SOLID ELECTRICAL INSULATING MATERIALS AT COMMERCIAL POWER FREQUENCIES
    MIL DTL 23053/5 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, FLEXIBLE, CROSSLINKED
    MIL DTL 23053/11 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, FLUORINATED ETHYLENE PROPYLENE, NON-CROSSLINKED
    ASTM D 876 : 2013 : REDLINE Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation
    MIL A 8243 : D ANTI-ICING AND DEICING-DEFROSTING FLUIDS
    MIL DTL 23053/12 : C INSULATION SLEEVING - ELECTRICAL, HEAT SHRINKABLE, POLYTETRAFLUOROETHYLENE
    MIL DTL 23053/1 : C INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, CROSSLINKED CHLORINATED POLYOLEFIN, FLEXIBLE
    MIL H 5606 : G HYDRAULIC FLUID, PETROLEUM BASE; AIRCRAFT; MISSILE AND ORDNANCE
    MIL F 46162 : D FUEL, DIESEL, REFEREE GRADE
    ASTM D 570 : 1998 : R2018 Standard Test Method for Water Absorption of Plastics
    MIL DTL 23053/6 : D INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, SEMI-RIGID, CROSSLINKED
    MIL STD 104 : C LIMITS FOR ELECTRICAL INSULATION COLOR
    ASTM D 638 : 2014 : REDLINE Standard Test Method for Tensile Properties of Plastics
    MIL DTL 23053/4 : D INSULATION SLEEVING, ELECTRICAL, HEAT SHRINKABLE, POLYOLEFIN, DUAL-WALL, OUTER WALL CROSSLINKED
    ASTM D 2671 : 2013 Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use
    ASTM D 374 : 1999 Standard Test Methods for Thickness of Solid Electrical Insulation
    ASTM D 746 : 2014 : REDLINE Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective