We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • SAE ARP 4990B : 2015

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    TURBINE FLOWMETER FUEL FLOW CALCULATIONS

    Available format(s):  Hardcopy, PDF

    Superseded date:  31-10-2020

    Language(s):  English

    Published date:  07-09-2015

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. REFERENCES
    3. BACKGROUND
    4. INTRODUCTION
    5. FUEL PROPERTY MEASUREMENTS AND CORRECTIONS
    6. TURBINE FLOWMETER CALIBRATION AND CORRECTIONS
    7. RECOMMENDATIONS
    8. NOTES
    APPENDIX A - ASTM AND API STANDARDS SUMMARY
    APPENDIX B - SAMPLE FUEL FLOW CALCULATION
    APPENDIX C - UNITS CONVERSION FACTORS

    Abstract - (Show below) - (Hide below)

    Specifies to the aerospace industry a procedure for the consistent and accurate calculation of fuel flow using turbine flowmeters during development, production, and post overhaul/repair gas turbine engine testing.

    General Product Information - (Show below) - (Hide below)

    Committee EG-1E
    Document Type Revision
    Product Note THIS STANDARD ALSO REFERS TO ASME 57-A-63, ASME 57-A-70, NASA CR 187108, TR-ENG-001, NRC No 29808.
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referenced By This Book - (Show below) - (Hide below)

    SAE AIR 5450 : 2014 ADVANCED DUCTED PROPULSOR IN-FLIGHT THRUST DETERMINATION
    SAE AIR 6202 : 2012 TEST CELL MASS FUEL FLOW MEASUREMENT USING CORIOLIS FLOW METERS
    SAE ARP 4755 : 2016 TURBOSHAFT/TURBOPROP GAS TURBINE ENGINE TEST CELL CORRELATION
    FAA AC 43-207 : 2002 CORRELATION, OPERATION, DESIGN, AND MODIFICATION OF TURBOFAN/JET ENGINE TEST CELLS
    SAE AS 5304 : 2011 STANDARD SPECIFICATION FOR TURBINE FLOWMETERS
    SAE ARP 741 : 2016 TURBOFAN AND TURBOJET GAS TURBINE ENGINE TEST CELL CORRELATION
    SAE AIR 5026B : 2014 TEST CELL INSTRUMENTATION
    SAE AIR 1703 : 2012 IN-FLIGHT THRUST DETERMINATION
    API 551 : 2016 PROCESS MEASUREMENT

    Standards Referencing This Book - (Show below) - (Hide below)

    ASTM D 3701 : 2017 : REDLINE Standard Test Method for Hydrogen Content of Aviation Turbine Fuels by Low Resolution Nuclear Magnetic Resonance Spectrometry
    ASTM D 1217 : 2015 : REDLINE Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
    ASTM D 2382 : 1988 Test Method for Heat of Combustion of Hydrocarbon Fuels by Bomb Calorimeter (High-Precision Method) (Withdrawn 1994)
    IEEE 268-1992 METRIC PRACTICE, STANDARD FOR
    ASTM D 341 : 2017 : REDLINE Standard Practice for Viscosity-Temperature Charts for Liquid Petroleum Products
    SAE ARP 741 : 2016 TURBOFAN AND TURBOJET GAS TURBINE ENGINE TEST CELL CORRELATION
    API MPM CH11.2.1 : 1984 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - COMPRESSIBILITY FACTORS FOR HYDROCARBONS: 0-90 DEGREES API GRAVITY RANGE
    ASTM D 240 : 2017 : REDLINE Standard Test Method for Heat of Combustion of Liquid Hydrocarbon Fuels by Bomb Calorimeter
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective