SAE ARP 994 : 2016
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
DESIGN OF TUBING INSTALLATIONS FOR AEROSPACE HYDRAULIC SYSTEMS
Available format(s)
Hardcopy , PDF
Superseded date
30-06-2023
Language(s)
English
Published date
17-11-2016
Publisher
1. SCOPE
2. APPLICABLE DOCUMENTS
3. TUBING AND FITTINGS
4. TUBE ROUTING
5. PROVISIONS FOR RELATIVE MOTION
6. SUPPORT, CLAMPING, AND BONDING
7. DIMENSIONAL ACCURACY
8. STRESS CONSIDERATIONS
9. CONTAMINATION CONTROL
10. FINISHES AND COATINGS
11. LINE IDENTIFICATION
12. NOTES
APPENDIX A - HYDRAULIC LINE SIZING
Specifies recommended practices for the design and selection of tube, hose, and fitting systems that are used to transmit hydraulic fluid on aircraft.
| Committee |
A-6C5
|
| DocumentType |
Revision
|
| Pages |
27
|
| PublisherName |
SAE International
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| SAE ARP 4925 : 2014 | AEROSPACE DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT HELICOPTER HYDRAULIC SYSTEMS |
| SAE J 1779 : 2013 | SHIP SYSTEMS AND EQUIPMENT - HYDRAULIC SYSTEM DESIGN CRITERIA FOR MARINE VEHICLES |
| SAE ARP4943A:2022 | Ground Support Equipment Hydraulic Systems, Design and Installation, Recommended Practices forARP4943A |
| MIL-H-8891 Revision A:1978 | HYDRAULIC SYSTEMS, MANNED FLIGHT VEHICLES TYPE 111 DESIGN, INSTALLATION AND DATA REQUIREMENTS FOR, GENERAL SPECIFICATION FOR |
| MIL-H-5440 Revision H:1993 | HYDRAULIC SYSTEMS, AIRCRAFT, TYPES 1 AND 11 DESIGN AND INSTALLATION REQUIREMENTS FOR |
| SAE AIR 4918 : 2013 | INDUSTRY PRACTICES AND GUIDELINES FOR THE SELECTION OF COILED TUBES, FLEXIBLE HOSES, SWIVELS, AND EXTENSION FITTINGS FOR AIRCRAFT FLUID SYSTEMS |
| DIN EN 12312-17:2009-08 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 17: AIR CONDITIONING EQUIPMENT |
| I.S. EN 12312-17:2004 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 17: AIR CONDITIONING EQUIPMENT |
| MIL-HDBK-516 Revision C:2014 | AIRWORTHINESS CERTIFICATION CRITERIA |
| SAE ARP 4752 : 2013 | AEROSPACE - DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT AIRCRAFT HYDRAULIC SYSTEMS |
| SAE ARP 5891 : 2014 | ACHIEVING CLEANLINESS STANDARDS FOR AIRCRAFT HYDRAULIC SYSTEMS DURING MANUFACTURE |
| SAE AS 4401 : 2013 | SEPARABLE FITTINGS, PERMANENT FITTINGS, TUBING, FLUID SYSTEMS 8000 PSI QUALIFICATION TEST STANDARD FOR |
| JSSG-2009 Revision A:2013 | Air Vehicle Subsystems |
| SAE ARP 1280 : 2014 | AEROSPACE - APPLICATION GUIDE FOR HYDRAULIC POWER TRANSFER UNITS |
| BS EN 12312-17 : 2004 | AIRCRAFT GROUND SUPPORT EQUIPMENT - SPECIFIC REQUIREMENTS - PART 17: AIR CONDITIONING EQUIPMENT |
| EN 12312-17:2004+A1:2009 | Aircraft ground support equipment - Specific requirements - Part 17: Air conditioning equipment |
| MIL-P-87210 Base Document:1984 | PNEUMATIC POWER SYSTEMS, HIGH PRESSURE |
| SAE AIR 5451 : 2017 | A GUIDE TO LANDING GEAR SYSTEM INTEGRATION |
| SAE ARP 1532 : 2015 | AIRCRAFT OXYGEN SYSTEM LINES, FABRICATION, TEST AND INSTALLATION |
| SAE ARP 4943 : 2008 | GROUND SUPPORT EQUIPMENT HYDRAULIC SYSTEMS, DESIGN AND INSTALLATION, RECOMMENDED PRACTICES FOR |
| SAE ARP 24 : 2013 | DETERMINATION OF HYDRAULIC PRESSURE DROP |
| SAE AIR 1569 : 1993 | HANDLING AND INSTALLATION PRACTICE FOR AEROSPACE HOSE ASSEMBLIES |
| SAE ARP 1835 : 2013 | PREPARATION FOR DELIVERY, GENERAL REQUIREMENTS FOR HOSE ASSEMBLIES |
| SAE AS 611F : 2010 | HOSE ASSEMBLY AND TUBING, POLYTETRAFLUOROETHYLENE, CLEANING METHODS FOR |
| SAE AIR 5693 : 2014 | COMPATIBILITY OF PTFE HOSE ASSEMBLIES WITH TYPICAL FLUIDS FOUND IN AEROSPACE APPLICATIONS |
| SAE AIR 5378 : 2013 | AIRCRAFT TUBE BENDING METHODS, TECHNIQUES AND TOOLING |
| SAE AS 1301 : 2015 | ADAPTERS - PORT CONNECTION, RING LOCKED DESIGN, INSTALLATION AND REMOVAL OF |
| SAE AIR 1564 : 2005 | CROSS REFERENCE FOR MATERIALS FOR FLUID SYSTEMS COMPONENTS INCLUDING MILITARY AND FEDERAL SPECIFICATIONS AND THEIR INTERNATIONAL EQUIVALENTS |
| SAE ARP 1897 : 2013 | CLAMP SELECTION AND INSTALLATION GUIDE |
| SAE AS 603 : 2015 | IMPULSE TESTING OF HYDRAULIC HOSE, TUBING, AND FITTING ASSEMBLIES |
| SAE AIR 1922 : 2017 | AEROSPACE - SYSTEM INTEGRATION FACTORS THAT AFFECT HYDRAULIC PUMP LIFE |
| SAE ARP 4146D : 2012 | COILED TUBING - TITANIUM ALLOY, HYDRAULIC APPLICATIONS, AEROSPACE |
| SAE ARP 1785 : 2013 | STANDARD CODES FOR OUTER SLEEVING ON HOSE ASSEMBLIES |
| SAE AIR 5386 : 2013 | HOSE AND HOSE ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE GUIDELINES, LISTING OF |
| SAE AIR 310 : 2013 | FITTINGS, CATALOG OF FLARED. FLARELESS, PIPE THREADED, PORT, HOSE AND OTHER TYPE TUBE STANDARD CONNECTORS |
| SAE AS 4467 : 2013 | STANDARDIZATION, HYDRAULIC TUBE WALLS |
| SAE AS 683 : 2012 | INSTALLATION PROCEDURES AND TORQUES FOR FLUID CONNECTIONS |
| SAE AIR 1047 : 2000 | A GUIDE FOR THE SELECTION OF QUICK-DISCONNECT COUPLINGS FOR AEROSPACE FLUID SYSTEMS |
| SAE AS 5959 : 2013 | AXIALLY SWAGED FITTINGS, INSTALLATION AND INSPECTION PROCEDURE |
| SAE ARP 4752 : 2013 | AEROSPACE - DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT AIRCRAFT HYDRAULIC SYSTEMS |
| SAE AMS 5561 : 2012 | STEEL, CORROSION AND HEAT-RESISTANT, WELDED AND DRAWN OR SEAMLESS AND DRAWN TUBING, 9.0MN - 20CR - 6.5NI - 0.28N, HIGH-PRESSURE HYDRAULIC |
| SAE AS 5586 : 2005 | GENERAL REQUIREMENTS FOR HYDRAULIC SYSTEM RESERVOIRS |
| SAE AS 85720 : 2015 | FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, HIGH PRESSURE BEAM SEAL, 5000/8000 PSI, GENERAL SPECIFICATION FOR |
| SAE AS 1055 : 2013 | FIRE TESTING OF FLEXIBLE HOSE, TUBE ASSEMBLIES, COILS, FITTINGS AND SIMILAR SYSTEM COMPONENTS |
| SAE ARP 1185 : 2013 | FLEXURE TESTING OF HYDRAULIC TUBING JOINTS AND FITTINGS |
| SAE AIR 6185 : 2015 | AEROSPACE - LIGHTNING EFFECTS ON HYDRAULIC TRANSPORT ELEMENTS ON AIRCRAFT |
| MIL-DTL-5513 Revision D:2012 | SWIVEL JOINT, HYDRAULIC |
| ISO 16682:2015 | Aerospace series Terminology for clamping devices |
| SAE AS 5440 : 2011 | HYDRAULIC SYSTEMS, AIRCRAFT, DESIGN AND INSTALLATION REQUIREMENTS FOR |
| MIL-PRF-81309 Revision G:2014 | CORROSION PREVENTIVE COMPOUNDS, WATER DISPLACING, ULTRA-THIN FILM |
| SAE AIR 5005 : 2015 | AEROSPACE - COMMERCIAL AIRCRAFT HYDRAULIC SYSTEMS |
| SAE AS 1709 : 2014 | COUPLING ASSEMBLY, HYDRAULIC SELF SEALING, QUICK DISCONNECT |
| SAE AIR 797 : 2013 | HOSE CHARACTERISTICS AND SELECTION CHART |
| SAE ARP 1709 : 2013 | COUPLING ASSEMBLY, HYDRAULIC SELF SEALING, QUICK DISCONNECT |
| MIL-PRF-87257 Revision C:2017 | HYDRAULIC FLUID, FIRE RESISTANT, LOW TEMPERATURE, SYNTHETIC HYDROCARBON BASE, AIRCRAFT AND MISSILE |
| SAE AIR 4918 : 2013 | INDUSTRY PRACTICES AND GUIDELINES FOR THE SELECTION OF COILED TUBES, FLEXIBLE HOSES, SWIVELS, AND EXTENSION FITTINGS FOR AIRCRAFT FLUID SYSTEMS |
| MIL-DTL-5541 Revision F:2006 | Chemical Conversion Coatings on Aluminum and Aluminum Alloys |
| SAE AS 24335 : 2013 | FLANGE, BULKHEAD MOUNTING, HYDRAULIC SELF-SEALING COUPLING |
| SAE AS 5902 : 2015 | INSTALLATION OF EXTERNALLY SWAGED FITTINGS |
| SAE AS 85421 : 2015 | FITTINGS, TUBE, FLUID SYSTEMS, SEPARABLE, BEAM SEAL, 3000/4000 PSI, GENERAL SPECIFICATION FOR |
| SAE AS 5958 : 2013 | FITTINGS, AXIALLY SWAGED TUBE WITH FLARELESS SEPARABLE, FLUID SYSTEM FOR OPERATING PRESSURES UP TO AND INCLUDING 5080 PSI (35 000 KPA), SPECIFICATION FOR |
| SAE AS 130 : 2013 | TUBE BENDING RADIUS |
| SAE AMS 4945 : 2014 | TITANIUM ALLOY TUBING, SEAMLESS, HYDRAULIC 3AL - 2.5V, CONTROLLED CONTRACTILE STRAIN RATIO COLD WORKED, STRESS RELIEVED |
| SAE ARP 1658 : 2014 | HOSE ASSEMBLIES, INSTALLED, VISUAL INSPECTION GUIDE FOR |
| SAE AS 5148 : 2013 | ASSEMBLY, INSTALLATION AND TORQUE FOR FLARELESS AND STRAIGHT THREAD FLUID FITTINGS AND TUBE ASSEMBLIES |
| SAE AIR 5426 : 2013 | FITTING AND FITTING ASSEMBLY SELECTION, INSTALLATION, INSPECTION AND MAINTENANCE OF |
| SAE MA 2094 : 2015 | TEST METHODS FOR TUBE-FITTING ASSEMBLIES, METRIC |
| SAE AIR 1388 : 1992 | SERVICE DAMAGE LIMITS FOR AIRCRAFT HYDRAULIC TUBING |
| SAE AMS 2700E : 2011 | PASSIVATION OF CORROSION RESISTANT STEELS |
| SAE AIR 1698 : 2013 | HOSE ASSEMBLY IDENTIFICATION PRACTICES |
| SAE ARP 584D : 2012 | COILED TUBING - CORROSION RESISTANT STEEL, HYDRAULIC APPLICATIONS, AEROSPACE |
| SAE AS 4459 : 2013 | FITTINGS, TUBE, FLUID SYSTEM 3000 PSIG (21000 KPA) RATED PRESSURE, EXTERNALLY SWAGED, SPECIFICATION FOR |
| SAE AMS 4083 : 2012 | ALUMINUM ALLOY TUBING, HYDRAULIC, SEAMLESS, DRAWN, ROUND, 1.0MG - 0.60SI - 0.28CU - 0.20CR (6061-T6), SOLUTION AND PRECIPITATION HEAT TREATED |
| SAE AS 4941 : 2015 | AEROSPACE - GENERAL REQUIREMENTS FOR COMMERCIAL AIRCRAFT HYDRAULIC COMPONENTS |
| SAE ARP 5891 : 2014 | ACHIEVING CLEANLINESS STANDARDS FOR AIRCRAFT HYDRAULIC SYSTEMS DURING MANUFACTURE |
| SAE AS 150 : 2014 | HOSE ASSEMBLY, TYPE CLASSIFICATIONS OF, BASIC PERFORMANCE AND FIRE RESISTANCE |
| SAE ARP 4925 : 2014 | AEROSPACE DESIGN AND INSTALLATION OF COMMERCIAL TRANSPORT HELICOPTER HYDRAULIC SYSTEMS |
| SAE AIR 1593 : 1980 | CLAMP LOADS AND BENDING STRESSES IN AIRCRAFT TUBING INSTALLATIONS |
| SAE ARP 4784 : 2013 | DEFINITIONS AND LIMITS, METAL MATERIAL DEFECTS AND SURFACE AND EDGE FEATURES, FLUID COUPLINGS, FITTINGS AND HOSE ENDS |
| SAE ARP 4698 : 2013 | GUIDE FOR CHOOSING A MINIMUM WALL THICKNESS OF TUBING FOR USE WITH WELD FITTINGS CODED FOR A RANGE OF WALL SIZES |
| SAE AS 25427 : 2015 | COUPLING ASSEMBLY, HYDRAULIC, SELF-SEALING, QUICK DISCONNECT |
| SAE AIR 1657 : 2003 | HANDBOOK OF HYDRAULIC METRIC CALCULATIONS |
| SAE AMS T 6845 : 2013 | TUBING, STEEL, CORROSION-RESISTANT (S30400), AEROSPACE VEHICLE HYDRAULIC SYSTEM 1/8 HARD CONDITION |
| SAE AS 2094 : 2011(S2018) | Test Methods for Tube-Fitting Assemblies(STABILIZED Jul 2018) |
| SAE ARP 899 : 2013 | TUBE FITTINGS, FLUID SYSTEMS, PERMANENT TYPE, GENERAL REQUIREMENTS FOR |
| FAA AC 20-128 : 0 | DESIGN CONSIDERATIONS FOR MINIMIZING HAZARDS CAUSED BY UNCONTAINED TURBINE ENGINE AND AUXILIARY POWER UNIT ROTOR FAILURE |
| ISO 8575:2016 | Aerospace — Fluid systems — Hydraulic system tubing |
| SAE AS 33611 : 2015 | TUBE BEND RADII |
£126.23
Excluding VAT
GBP
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.