We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
  • SAE AS 4716C: 2017

    Superseded A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
    Add to Watchlist
    This Standard has been added successfully to your Watchlist.
    Please visit My Watchlist to see all standards that you are watching.
    Please log in or to add this standard to your Watchlist.
    We could not add this standard to your Watchlist.
    Please retry or contact support for assistance.
    You need to be logged in to add this standard to your Watchlist.
    Please log in now or create an account to add.
    You already added this Product in the Watchlist.

    GLAND DESIGN, O-RING AND OTHER SEALS

    Available format(s):  Hardcopy, PDF

    Superseded date:  12-11-2021

    Language(s):  English

    Published date:  12-12-2017

    Publisher:  SAE International

    Add to Watchlist

    Add To Cart

    Table of Contents - (Show below) - (Hide below)

    1. SCOPE
    2. REFERENCES
    3. TECHNICAL REQUIREMENTS
    4. NOTES
    APPENDIX A - O-RING SQUEEZE CALCULATIONS AND DESIGN CONSIDERATIONS
    APPENDIX B - GLAND FILL AND O-RING OCCUPANCY CALCULATIONS AND DESIGN
                 CONSIDERATIONS IGNORING SWELL AND AT AMBIENT TEMPERATURE
    APPENDIX C - GLAND FILL AND O-RING OCCUPANCY CALCULATIONS AND DESIGN
                 CONSIDERATIONS WITH VOLUME SWELL AT 275 DEGREES F
    (135 DEGREES C)

    Abstract - (Show below) - (Hide below)

    This SAE Aerospace Standard (AS) provides standardized gland (groove) design criteria and dimensions for O-ring seal glands for static and dynamic applications, and other seals

    General Product Information - (Show below) - (Hide below)

    Committee A-6C2
    Document Type Revision
    Publisher SAE International
    Status Superseded
    Superseded By
    Supersedes

    Standards Referencing This Book - (Show below) - (Hide below)

    SAE AS 5781 : 2015 RETAINERS (BACKUP RINGS), HYDRAULIC AND PNEUMATIC, POLYTETRAFLUOROETHYLENE RESIN, SINGLE TURN, SCARF-CUT, FOR USE IN AS4716 GLANDS
    SAE ARP 5555 : 2016 RECOMMENDATIONS FOR INSTALLATION OF SEALS IN STANDARD GLANDS
    SAE AS 5782 : 2015 RETAINERS (BACKUP RINGS), HYDRAULIC AND PNEUMATIC, POLYTETRAFLUOROETHYLENE RESIN, SOLID, UN-CUT, FOR USE IN AS4716 GLANDS
    SAE AS 568 : 2014 AEROSPACE SIZE STANDARD FOR O-RINGS
    SAE AS 5857 : 2010 GLAND DESIGN, O-RING AND OTHER ELASTOMERIC SEALS, STATIC APPLICATIONS
    SAE AS 6235 : 2015 FACE SEAL GLAND DESIGN, STATIC, O-RING AND OTHER SEALS FOR AEROSPACE HYDRAULIC AND PNEUMATIC APPLICATIONS
    SAE AS 8791 : 2014 HYDRAULIC AND PNEUMATIC RETAINERS (BACK-UP RINGS), POLYTETRAFLUOROETHYLENE (PTFE) RESIN
    MIL G 5514 : G GLAND DESIGN, PACKINGS, HYDRAULIC GENERAL REQUIREMENTS FOR
    SAE ARP 4727 : 2004(S2013) GLAND DESIGN, COMPUTATION OF SEAL SQUEEZE AND GLAND VOLUME
    SAE ARP 5935 : 2013 USE OF HVOF THERMAL SPRAY COATINGS FOR HARD CHROME REPLACEMENT IN LANDING GEAR APPLICATIONS
    SAE AIR 6079 : 2010 SELECTION OF METALLIC SPRING ENERGIZED SEALS FOR AEROSPACE
    ISO 4287-1:1984 Surface roughness — Terminology — Part 1: Surface and its parameters
    SAE AMS 2452 : 2011 SUPERFINISHING OF HVOF APPLIED TUNGSTEN CARBIDE COATINGS
    • Access your standards online with a subscription

      Features

      • Simple online access to standards, technical information and regulations
      • Critical updates of standards and customisable alerts and notifications
      • Multi - user online standards collection: secure, flexibile and cost effective