• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN 13483 : 2013

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

RUBBER AND PLASTIC HOSES AND HOSE ASSEMBLIES WITH INTERNAL VAPOUR RECOVERY FOR MEASURED FUEL DISPENSING SYSTEMS - SPECIFICATION
Superseded date

23-11-2022

Published date

11-07-2013

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Classification
5 Materials and construction
6 Pressure requirements
7 Dimensions and tolerances
8 Physical properties
9 End fittings
10 Type tests
11 Frequency of testing
12 Marking
Annex A (normative) - Test method for determination
        of low temperature class resistance at
        -30 degrees C (for normal temperature
        class) and -40 degrees C (for low
        temperature class)
Annex B (normative) - Test method for pressure
        requirements of vapour recovery hoses and tubes
Annex C (normative) - Test method for determination
        of change in length due to swelling
Annex D (normative) - Test method for determination
        of pressure loss
Annex E (normative) - Method for determination of
        adhesion between components
Annex F (normative) - Test method for the
        determination of low temperature flexibility
Annex G (normative) - Test method for the
        determination of rate of fuel permeation
Annex H (normative) - Test method for flammability
Annex I (normative) - Test method for the
        determination of leakage (leak test)
Annex J (normative) - Test method for fatigue
        strength under reversed bending stresses
        (flex test)
Annex K (normative) - End-fitting pull-off test
Annex L (normative) - Test frequency for type
        tests and routine tests
Annex M (informative) - Test frequency for
        production acceptance tests
Bibliography

Defines the requirements and test methods for verification for hose assemblies with vapour recovery for delivery systems on petrol filling stations.

Committee
CT 17
DocumentType
Test Method
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy
Supersedes

Standards Relationship
ONORM EN 13483 : 2013 Identical
NF EN 13483 : 2013 Identical
NBN EN 13483 : 2013 Identical
NEN EN 13483 : 2013 Identical
NS EN 13483 : 2013 Identical
I.S. EN 13483:2013 Identical
UNE-EN 13483:2013 Identical
SN EN 13483 : 2013 Identical
BS EN 13483:2013 Identical
EN 13483:2013 Identical
DIN EN 13483:2013-09 Identical

EN ISO 8330:2014 Rubber and plastics hoses and hose assemblies - Vocabulary (ISO 8330:2014)
EN ISO 1402:2009 Rubber and plastics hoses and hose assemblies - Hydrostatic testing (ISO 1402:2009)
EN ISO 4671:2007/A1:2011 Rubber and plastics hoses and hose assemblies - Methods of measurement of the dimensions of hoses and the lengths of hose assemblies - Amendment 1: Clarification of position at which outside diameter is measured (ISO 4671:2007/Amd 1:2011)
EN 228:2012+A1:2017 Automotive fuels - Unleaded petrol - Requirements and test methods
ISO 6801:1983 Rubber or plastics hoses Determination of volumetric expansion
ISO 4649:2017 Rubber, vulcanized or thermoplastic — Determination of abrasion resistance using a rotating cylindrical drum device
EN ISO 1307:2008 Rubber and plastics hoses - Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses (ISO 1307:2006)
ISO 188:2011 Rubber, vulcanized or thermoplastic — Accelerated ageing and heat resistance tests
EN ISO 8031:2009 Rubber and plastics hoses and hose assemblies - Determination of electrical resistance and conductivity (ISO 8031:2009)
EN ISO 7326:2016 Rubber and plastics hoses - Assessment of ozone resistance under static conditions (ISO 7326:2016)
ISO 7326:2016 Rubber and plastics hoses Assessment of ozone resistance under static conditions
EN ISO 8033:2017 Rubber and plastics hoses - Determination of adhesion between components (ISO 8033:2016)
ISO 8330:2007 Rubber and plastics hoses and hose assemblies Vocabulary
EN 26801:1993/A1:2011 RUBBER OR PLASTICS HOSES - DETERMINATION OF VOLUMETRIC EXPANSION (ISO 6801:1983/AMD 1:2011)
ISO 37:2017 Rubber, vulcanized or thermoplastic — Determination of tensile stress-strain properties
ISO 4671:2007 Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies
ISO 554:1976 Standard atmospheres for conditioning and/or testing — Specifications
ISO 1402:2009 Rubber and plastics hoses and hose assemblies Hydrostatic testing
ISO 1307:2006 Rubber and plastics hoses — Hose sizes, minimum and maximum inside diameters, and tolerances on cut-to-length hoses
ISO 8033:2016 Rubber and plastics hoses Determination of adhesion between components
ISO 8031:2009 Rubber and plastics hoses and hose assemblies Determination of electrical resistance and conductivity
ISO 527-1:2012 Plastics Determination of tensile properties Part 1: General principles
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.