• There are no items in your cart
We noticed you’re not on the correct regional site. Switch to our AMERICAS site for the best experience.
Dismiss alert

UNI EN ISO 6185-4 : 2011

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

INFLATABLE BOATS - PART 4: BOATS WITH A HULL LENGTH OF BETWEEN 8 M AND 24 M WITH A MOTOR POWER RATING OF 15 KW AND GREATER
Superseded date

15-11-2018

Published date

01-01-2011

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols
5 Materials
6 Functional components
7 Safety requirements of the completed boat
8 Builder's plate(s)
9 Owner's manual
10 Standard equipment
Annex A (informative) - Typical Type IX powered boat
Annex B (informative) - Typical Type X powered boat
Annex ZA (informative) - Relationship between this
         International Standard and the Essential
         Requirements of EU Directive 94/25/EC as
         amended by Directive 2003/44/EC
Bibliography

Describes the minimum safety characteristics required for the design, materials, manufacture and testing of rigid inflatable boats (RIBs) with a hull length of between 8 m and 24 m and with a motor power rating of 15 kW and greater.

DocumentType
Standard
PublisherName
Ente Nazionale Italiano di Unificazione (UNI)
Status
Superseded
SupersededBy

Standards Relationship
EN ISO 6185-4:2011 Identical
ISO 6185-4:2011 Identical

ISO 10239:2014 Small craft Liquefied petroleum gas (LPG) systems
ISO 12215-5:2008 Small craft Hull construction and scantlings Part 5: Design pressures for monohulls, design stresses, scantlings determination
ISO 7010:2011 Graphical symbols Safety colours and safety signs Registered safety signs
ISO 14946:2001 Small craft Maximum load capacity
ISO 4675:2017 Rubber- or plastics-coated fabrics — Low-temperature bend test
ISO 11591:2011 Small craft, engine-driven Field of vision from helm position
ISO 12217-3:2015 Small craft — Stability and buoyancy assessment and categorization — Part 3: Boats of hull length less than 6 m
ISO 10088:2013 Small craft — Permanently installed fuel systems
ISO 2411:2017 Rubber- or plastics-coated fabrics — Determination of coating adhesion
ISO 11105:1997 Small craft Ventilation of petrol engine and/or petrol tank compartments
ISO 8666:2016 Small craft Principal data
ISO 8847:2004 Small craft Steering gear Cable and pulley systems
ISO 15084:2003 Small craft Anchoring, mooring and towing Strong points
ISO 6185-3:2014 Inflatable boats Part 3: Boats with a hull length less than 8 m with a motor rating of 15 kW and greater
ISO 10133:2012 Small craft Electrical systems Extra-low-voltage d.c. installations
ISO 12217-1:2015 Small craft — Stability and buoyancy assessment and categorization — Part 1: Non-sailing boats of hull length greater than or equal to 6 m
ISO 12215-3:2002 Small craft — Hull construction and scantlings — Part 3: Materials: Steel, aluminium alloys, wood, other materials
ISO 8848:1990 Small craft Remote steering systems
ISO 10592:1994 Small craft Hydraulic steering systems
ISO 11812:2001 Small craft Watertight cockpits and quick-draining cockpits
ISO 10240:2004 Small craft Owner's manual
ISO 21487:2012 Small craft — Permanently installed petrol and diesel fuel tanks
ISO 13297:2014 Small craft Electrical systems Alternating current installations
ISO 15085:2003 Small craft Man-overboard prevention and recovery
ISO 12216:2002 Small craft Windows, portlights, hatches, deadlights and doors Strength and watertightness requirements
ISO 3011:1997 Rubber- or plastics-coated fabrics Determination of resistance to ozone cracking under static conditions
ISO 4674-1:2016 Rubber- or plastics-coated fabrics Determination of tear resistance Part 1: Constant rate of tear methods
ISO 10087:2006 Small craft Craft identification Coding system
ISO 12215-6:2008 Small craft — Hull construction and scantlings — Part 6: Structural arrangements and details
ISO 1817:2015 Rubber, vulcanized or thermoplastic Determination of the effect of liquids
ISO 14945:2004 Small craft Builder's plate
ISO 8099:2000 Small craft Toilet waste retention systems

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.