ISO 13846:2000
|
Plastics piping systems End-load-bearing and non-end-load-bearing assemblies and joints for thermoplastics pressure piping Test method for long-term leaktightness under internal water pressure
|
ISO 3213:2009
|
Polypropylene (PP) pipes Effect of time and temperature on the expected strength
|
ISO 4422-3:1996
|
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 3: Fittings and joints
|
ISO 13953:2001
|
Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
|
ISO 15874-3:2013
|
Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 3: Fittings
|
ISO 15877-3:2009
|
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 3: Fittings
|
ISO 10146:1997
|
Crosslinked polyethylene (PE-X) pipes Effect of time and temperature on the expected strength
|
ISO 15875-5:2003
|
Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 5: Fitness for purpose of the system
|
ISO 13968:2008
|
Plastics piping and ducting systems — Thermoplastics pipes — Determination of ring flexibility
|
ISO 15874-1:2013
|
Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 1: General
|
ISO 161-1:1996
|
Thermoplastics pipes for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series
|
ISO 3501:2015
|
Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for resistance to pull-out under constant longitudinal force
|
ISO 4422-1:1996
|
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 1: General
|
ISO 3:1973
|
Preferred numbers Series of preferred numbers
|
ISO 3459:2015
|
Plastic piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under negative pressure
|
ISO 15877-2:2009
|
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 2: Pipes
|
ISO 15875-2:2003
|
Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 2: Pipes
|
ISO 12230:2012
|
Polybutene-1 (PB-1) pipes — Effect of time and temperature on the expected strength
|
ISO 527-2:2012
|
Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
|
ISO 11414:2009
|
Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
|
ISO 15877-1:2009
|
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 1: General
|
ISO 15874-2:2013
|
Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 2: Pipes
|
ISO 15876-1:2017
|
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 1: General
|
ISO 3126:2005
|
Plastics piping systems Plastics components Determination of dimensions
|
ISO 161-2:1996
|
Thermoplastics pipes for the conveyance of fluids — Nominal outside diameters and nominal pressures — Part 2: Inch-based series
|
ISO 15876-3:2017
|
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 3: Fittings
|
ISO 15877-5:2009
|
Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C) Part 5: Fitness for purpose of the system
|
ISO 13783:1997
|
Plastics piping systems — Unplasticized poly(vinyl chloride) (PVC-U) end-load-bearing double-socket joints — Test method for leaktightness and strength while subjected to bending and internal pressure
|
ISO 13844:2015
|
Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with plastic pressure pipes Test method for leaktightness under negative pressure, angular deflection and deformation
|
ISO 16871:2003
|
Plastics piping and ducting systems Plastics pipes and fittings Method for exposure to direct (natural) weathering
|
ISO 472:2013
|
Plastics Vocabulary
|
ISO 13954:1997
|
Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
|
ISO 4422-2:1996
|
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 2: Pipes (with or without integral sockets)
|
ISO 4422-4:1997
|
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 4: Valves and ancillary equipment
|
ISO 13955:1997
|
Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
|
ISO 15876-2:2017
|
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 2: Pipes
|
ISO 15875-1:2003
|
Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 1: General
|
ISO 4422-5:1997
|
Pipes and fittings made of unplasticized poly(vinyl chloride) (PVC-U) for water supply Specifications Part 5: Fitness for purpose of the system
|
ISO 497:1973
|
Guide to the choice of series of preferred numbers and of series containing more rounded values of preferred numbers
|
ISO 13761:2017
|
Plastics pipes and fittings — Pressure reduction factors for polyethylene pipeline systems for use at temperatures above 20 degrees C
|
ISO 15875-3:2003
|
Plastics piping systems for hot and cold water installations — Crosslinked polyethylene (PE-X) — Part 3: Fittings
|
ISO 15874-5:2013
|
Plastics piping systems for hot and cold water installations — Polypropylene (PP) — Part 5: Fitness for purpose of the system
|
ISO 11413:2008
|
Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
|
ISO 1043-1:2011
|
Plastics — Symbols and abbreviated terms — Part 1: Basic polymers and their special characteristics
|
ISO 9969:2016
|
Thermoplastics pipes Determination of ring stiffness
|
ISO/TR 9080:1992
|
Thermoplastics pipes for the transport of fluids — Methods of extrapolation of hydrostatic stress rupture data to determine the long-term hydrostatic strength of thermoplastics pipe materials
|
ISO 15876-5:2017
|
Plastics piping systems for hot and cold water installations — Polybutene (PB) — Part 5: Fitness for purpose of the system
|
ISO 527-1:2012
|
Plastics Determination of tensile properties Part 1: General principles
|
ISO 3503:2015
|
Plastics piping systems Mechanical joints between fittings and pressure pipes Test method for leaktightness under internal pressure of assemblies subjected to bending
|
ISO 13845:2015
|
Plastics piping systems Elastomeric-sealing-ring-type socket joints for use with thermoplastic pressure pipes Test method for leaktightness under internal pressure and with angular deflection
|