12/30256675 DC : 0

Superseded

BS ISO 4437-5 - PLASTICS PIPING SYSTEMS FOR THE SUPPLY OF GASEOUS FUELS - POLYETHYLENE (PE) - PART 5: FITNESS FOR PURPOSE

Available format(s)

Hardcopy , PDF

Superseded date

01-31-2014

Language(s)

English

Publisher

British Standards Institution

Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 Fitness for purpose
5 Design coefficient
Annex A (informative) - Derating coefficients for
        operating temperatures
Annex B (normative) - Rapid crack propagation (RCP)
        resistance of pipe at temperature less
        than 0 degree C
Bibliography

BS ISO 4437-5

Committee	PRI/88/2
DocumentType	Draft
Pages	19
PublisherName	British Standards Institution
Status	Superseded
SupersededBy	BS ISO 4437-5:2014

ISO 13953:2001	Polyethylene (PE) pipes and fittings — Determination of the tensile strength and failure mode of test pieces from a butt-fused joint
ISO 1167-2:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids — Determination of the resistance to internal pressure — Part 2: Preparation of pipe test pieces
ISO 10838-3:2001	Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 3: Thermoplastics fittings for pipes of nominal outside diameter less than or equal to 63 mm
ISO 13956:2010	Plastics pipes and fittings Decohesion test of polyethylene (PE) saddle fusion joints Evaluation of ductility of fusion joint interface by tear test
ISO 10838-2:2000	Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 2: Metal fittings for pipes of nominal outside diameter greater than 63 mm
ISO 10838-1:2000	Mechanical fittings for polyethylene piping systems for the supply of gaseous fuels Part 1: Metal fittings for pipes of nominal outside diameter less than or equal to 63 mm
ISO 1167-4:2007	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 4: Preparation of assemblies
ISO 13477:2008	Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Small-scale steady-state test (S4 test)
ISO/TS 10839:2000	Polyethylene pipes and fittings for the supply of gaseous fuels — Code of practice for design, handling and installation
ISO 11414:2009	Plastics pipes and fittings Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion
ISO 12162:2009	Thermoplastics materials for pipes and fittings for pressure applications Classification, designation and design coefficient
ISO 13478:2007	Thermoplastics pipes for the conveyance of fluids — Determination of resistance to rapid crack propagation (RCP) — Full-scale test (FST)
ISO 13954:1997	Plastics pipes and fittings Peel decohesion test for polyethylene (PE) electrofusion assemblies of nominal outside diameter greater than or equal to 90 mm
ISO 13955:1997	Plastics pipes and fittings Crushing decohesion test for polyethylene (PE) electrofusion assemblies
CEN/TS 1555-7:2013	Plastics piping systems for the supply of gaseous fuels - Polyethylene (PE) - Part 7: Guidance for the assessment of conformity
ISO 11413:2008	Plastics pipes and fittings Preparation of test piece assemblies between a polyethylene (PE) pipe and an electrofusion fitting
ISO 1167-1:2006	Thermoplastics pipes, fittings and assemblies for the conveyance of fluids Determination of the resistance to internal pressure Part 1: General method