• There are no items in your cart

12/30275810 DC : 0

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

BS EN 16506 - SYSTEMS FOR RENOVATION OF DRAINS AND SEWERS - LINING WITH A RIGIDLY ANCHORED PLASTICS INNER LAYER (RAPL)
Available format(s)

Hardcopy , PDF

Superseded date

10-31-2014

Language(s)

English

Foreword
1 Scope
2 Normative references
3 Terms and definitions
4 Symbols and abbreviations
5 Pipes at the 'M'-Stage
6 Marking
7 Fittings at the 'M' stage
8 Lining system at the 'I' stage
9 Installation
10 Documentation
Annex A (normative) - Anchoring strength of plastics
        inner layer - Test method for bond strength by
        pull-off
Annex B (normative) - I - Stage crushing strength test
Bibliography

BS EN 16506.

Committee
B/505/13/C
DocumentType
Draft
Pages
28
PublisherName
British Standards Institution
Status
Superseded
SupersededBy

Standards Relationship
PREN 16506 : DRAFT 2012 Identical

EN 728:1997 Plastics piping and ducting systems - Polyolefin pipes and fittings - Determination of oxidation induction time
EN 1107-2 : 2001 Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
EN ISO 527-2:2012 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics (ISO 527-2:2012)
EN 1542:1999 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
ISO 2039-1:2001 Plastics Determination of hardness Part 1: Ball indentation method
EN ISO 6259-1:2015 Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1:2015)
ISO 75-2:2013 Plastics — Determination of temperature of deflection under load — Part 2: Plastics and ebonite
EN 13380:2001 General requirements for components used for renovation and repair of drain and sewer systems outside buildings
CEN/TR 14920:2005 Jetting resistance of drain and sewer pipes - Moving jet test method
ISO 527-2:2012 Plastics — Determination of tensile properties — Part 2: Test conditions for moulding and extrusion plastics
ISO 11296-1:2009 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 1: General
ISO 6259-1:2015 Thermoplastics pipes Determination of tensile properties Part 1: General test method
EN 445:2007 Grout for prestressing tendons - Test methods
EN 196-1:2016 Methods of testing cement - Part 1: Determination of strength
EN ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite (ISO 75-2:2013)
ISO 4624:2016 Paints and varnishes — Pull-off test for adhesion
ISO 11296-7:2011 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks Part 7: Lining with spirally-wound pipes
EN 1979:1999 Plastics piping and ducting systems - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
EN ISO 2039-1 : 2003 PLASTICS - DETERMINATION OF HARDNESS - PART 1: BALL INDENTATION METHOD (ISO 2039-1:2001)
ISO 1183-1:2012 Plastics Methods for determining the density of non-cellular plastics Part 1: Immersion method, liquid pyknometer method and titration method
EN ISO 4624:2016 Paints and varnishes - Pull-off test for adhesion (ISO 4624:2016)
EN 206-1:2000/A2:2005 CONCRETE - PART 1: SPECIFICATION, PERFORMANCE, PRODUCTION AND CONFORMITY
EN 1015-6:1998/A1:2006 METHODS OF TEST FOR MORTAR FOR MASONRY - PART 6: DETERMINATION OF BULK DENSITY OF FRESH MORTAR
ISO 10544:1992 Cold-reduced steel wire for the reinforcement of concrete and the manufacture of welded fabric
EN 1610:2015 Construction and testing of drains and sewers
EN 1916:2002/AC:2008 CONCRETE PIPES AND FITTINGS, UNREINFORCED, STEEL FIBRE AND REINFORCED
EN 13067:2012 Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies
PREN ISO 11296-7 : DRAFT 2012 PLASTICS PIPING SYSTEMS FOR RENOVATION OF UNDERGROUND NONPRESSURE DRAINAGE AND SEWERAGE NETWORKS - PART 7: LINING WITH SPIRALLY-WOUND PIPES (ISO 11296-7:2011)
EN ISO 1133:2005 PLASTICS - DETERMINATION OF THE MELT MASS-FLOW RATE (MFR) AND THE MELT VOLUME-FLOW RATE (MVR) OF THE THERMOPLASTICS
ISO 527-3:1995 Plastics Determination of tensile properties Part 3: Test conditions for films and sheets
EN ISO 527-3:1995/AC:2002 PLASTICS - DETERMINATION OF TENSILE PROPERTIES - PART 3: TEST CONDITIONS FOR FILMS AND SHEETS
ISO 1133:2005 Plastics Determination of the melt mass-flow rate (MFR) and the melt volume-flow rate (MVR) of thermoplastics
EN 14117:2004 Products systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products
EN ISO 1183-1:2012 Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1:2012)

View more information
US$23.96
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.