15/30286010 DC : 0
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
03-31-2017
English
Foreword
Introduction
1 Scope
2 Normative references
3 Terms and definitions
4 General requirements
5 Protection against electric shock hazards
6 Protection against electrical fire hazards
7 Protection against thermal hazards
8 Protection against mechanical hazards
9 Protection against abnormal operation hazards
10 Electric power source
11 Wiring
12 Electric motors and generators
13 Non-motor loads
14 Controls
15 Manuals and technical documentation
16 Marking
17 Tests
Annex A (informative) - List of significant hazards
Annex B (normative) - TN-systems: protection against
indirect contact (See also IEC 60364-4-41:2005,
and IEC 60364-6:2006 for additional clarification.)
All parts of this Annex apply to both self-powered
and externally-powered machines
Annex C (informative) - Explanation of emergency operation
functions (based upon IEC 60204-1 Annex E) All parts of
this Annex apply to both self-powered and
externally-powered EMM
Annex D (informative) - Comparison of selected requirements
of ISO 14990, UN ECE R100:2011, and ISO 6469-3:2011
Bibliography
BS ISO 14990-1.
Committee |
B/513/1
|
DocumentType |
Draft
|
Pages |
82
|
PublisherName |
British Standards Institution
|
Status |
Superseded
|
SupersededBy |
ISO 14572:2011 | Road vehicles — Round, sheathed, 60 V and 600 V screened and unscreened single- or multi-core cables — Test methods and requirements for basic- and high-performance cables |
IEC 61800-3:2017 | Adjustable speed electrical power drive systems - Part 3: EMC requirements and specific test methods |
IEC 60364-5-54:2011 | Low-voltage electrical installations - Part 5-54: Selection and erection of electrical equipment - Earthing arrangements and protective conductors |
IEC 60038:2009 | IEC standard voltages |
ISO 7010:2011 | Graphical symbols Safety colours and safety signs Registered safety signs |
ISO 20474-1:2017 | Earth-moving machinery — Safety — Part 1: General requirements |
IEC 61000-6-4:2006+AMD1:2010 CSV | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-4: GENERIC STANDARDS - EMISSION STANDARD FOR INDUSTRIAL ENVIRONMENTS |
IEC 60228:2004 | Conductors of insulated cables |
ISO 14122-3:2016 | Safety of machinery — Permanent means of access to machinery — Part 3: Stairs, stepladders and guard-rails |
IEC 61984:2008 | Connectors - Safety requirements and tests |
ISO 14122-1:2016 | Safety of machinery — Permanent means of access to machinery — Part 1: Choice of fixed means and general requirements of access |
IEC 60695-1-30:2017 | Fire hazard testing - Part 1-30: Guidance for assessing the fire hazard of electrotechnical products - Preselection testing process - General guidelines |
ISO 15817:2012 | Earth-moving machinery — Safety requirements for remote operator control systems |
IEC 60695-1-1:1999 | Fire hazard testing - Part 1-1: Guidance for assessing the fire hazard of electrotechnical products - General guidelines |
IEC 60364-4-41:2005+AMD1:2017 CSV | Low voltage electrical installations - Part 4-41: Protection for safety - Protection against electric shock |
ISO 6405-2:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 2: Symbols for specific machines, equipment and accessories |
ISO 13732-1:2006 | Ergonomics of the thermal environment — Methods for the assessment of human responses to contact with surfaces — Part 1: Hot surfaces |
IEC GUIDE 106:1996 | Guide for specifying environmental conditions for equipmentperformance rating |
IEC 60204-1:2016 | Safety of machinery - Electrical equipment of machines - Part 1: General requirements |
IEC 61000-6-1 : 3.0 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-1: GENERIC STANDARDS - IMMUNITY STANDARD FOR RESIDENTIAL, COMMERCIAL AND LIGHT-INDUSTRIAL ENVIRONMENTS |
IEC 60204-11:2000 | Safety of machinery - Electrical equipment of machines - Part 11: Requirements for HV equipment for voltages above 1 000 V a.c. or 1 500 V d.c. and not exceeding 36 kV |
IEC 60947-5-1 : 4.0 | LOW-VOLTAGE SWITCHGEAR AND CONTROLGEAR - PART 5-1: CONTROL CIRCUIT DEVICES AND SWITCHING ELEMENTS - ELECTROMECHANICAL CONTROL CIRCUIT DEVICES |
ISO 14118:2000 | Safety of machinery Prevention of unexpected start-up |
ISO 13851:2002 | Safety of machinery Two-hand control devices Functional aspects and design principles |
IEC 60204-32:2008 | Safety of machinery - Electrical equipment of machines - Part 32: Requirements for hoisting machines |
IEC 60269-1:2006+AMD1:2009+AMD2:2014 CSV | Low-voltage fuses - Part 1: General requirements |
IEC 60695-1-20:2016 | Fire hazard testing - Part 1-20: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - General guidance |
IEC 60947-7-1:2009 | Low-voltage switchgear and controlgear - Part 7-1: Ancillary equipment - Terminal blocks for copper conductors |
ISO 6165:2012 | Earth-moving machinery — Basic types — Identification and terms and definitions |
ISO 6011:2003 | Earth-moving machinery — Visual display of machine operation |
IEC 61082-1:2014 RLV | Preparation of documents used in electrotechnology - Part 1: Rules |
ISO 12100:2010 | Safety of machinery — General principles for design — Risk assessment and risk reduction |
ISO 14122-4:2016 | Safety of machinery — Permanent means of access to machinery — Part 4: Fixed ladders |
IEC 60757:1983 | Code for designation of colours |
ISO/TR 14121-2:2012 | Safety of machinery — Risk assessment — Part 2: Practical guidance and examples of methods |
ISO 9244:2008 | Earth-moving machinery Machine safety labels General principles |
IEC 61558-2-17:1997 | Safety of power transformers, power supply units and similar - Part2: Particular requirements for transformers for switch mode powersupplies |
IEC 60364-6:2016 | Low voltage electrical installations - Part 6: Verification |
IEC 61180-2:1994 | High-voltage test techniques for low-voltage equipment - Part 2: Test equipment |
IEC 61558-1:2017 | Safety of transformers, reactors, power supply units and combinations thereof - Part 1: General requirements and tests |
ISO 2860:1992 | Earth-moving machinery — Minimum access dimensions |
ISO 6722-1:2011 | Road vehicles — 60 V and 600 V single-core cables — Part 1: Dimensions, test methods and requirements for copper conductor cables |
IEC 61084-1:2017 | Cable trunking systems and cable ducting systems for electrical installations - Part 1: General requirements |
IEC 60529:1989+AMD1:1999+AMD2:2013 CSV | Degrees of protection provided by enclosures (IP Code) |
CISPR 61000-6-3:1996 | Electromagnetic compatibility (EMC) - Part 6: Generic standards - Section 3: Emission standard for residential, commercial and light-industrial environments |
IEC 60947-1:2007+AMD1:2010+AMD2:2014 CSV | Low-voltage switchgear and controlgear - Part 1: General rules |
ISO 15998:2008 | Earth-moving machinery Machine-control systems (MCS) using electronic components Performance criteria and tests for functional safety |
ISO 6405-1:2017 | Earth-moving machinery Symbols for operator controls and other displays Part 1: Common symbols |
ISO 13849-2:2012 | Safety of machinery — Safety-related parts of control systems — Part 2: Validation |
IEC 61230:2008 | Live working - Portable equipment for earthing or earthing and short-circuiting |
ISO 3457:2003 | Earth-moving machinery Guards Definitions and requirements |
IEC 60034-1:2017 | Rotating electrical machines - Part 1: Rating and performance |
IEC 61496-1:2012 | Safety of machinery - Electro-sensitive protective equipment - Part 1: General requirements and tests |
IEC 60695-1-21:2016 | Fire hazard testing - Part 1-21: Guidance for assessing the fire hazard of electrotechnical products - Ignitability - Summary and relevance of test methods |
HD 516 S2:1997/A2:2008 | GUIDE TO USE OF LOW VOLTAGE HARMONIZED CABLES |
ISO 3864-1:2011 | Graphical symbols Safety colours and safety signs Part 1: Design principles for safety signs and safety markings |
ISO 13766:2006 | Earth-moving machinery Electromagnetic compatibility |
ISO 13850:2015 | Safety of machinery Emergency stop function Principles for design |
IEC 60947-5-2:2007+AMD1:2012 CSV | Low-voltage switchgear and controlgear - Part 5-2: Control circuitdevices and switching elements - Proximity switches |
IEC 60947-3:2008+AMD1:2012+AMD2:2015 CSV | Low-voltage switchgear and controlgear - Part 3: Switches, disconnectors, switch-disconnectors and fuse-combination units |
IEC 61439-1:2011 | Low-voltage switchgear and controlgear assemblies - Part 1: General rules |
IEC 60947-2:2016 | Low-voltage switchgear and controlgear - Part 2: Circuit-breakers |
ISO 7000:2014 | Graphical symbols for use on equipment Registered symbols |
IEC 61140:2016 | Protection against electric shock - Common aspects for installation and equipment |
IEC 60695-1-11:2014 | Fire hazard testing - Part 1-11: Guidance for assessing the fire hazard of electrotechnical products - Fire hazard assessment |
ISO 14122-2:2016 | Safety of machinery — Permanent means of access to machinery — Part 2: Working platforms and walkways |
IEC 60071-1:2006+AMD1:2010 CSV | Insulation co-ordination - Part 1: Definitions, principles and rules |
IEC 60309-1:1999+AMD1:2005+AMD2:2012 CSV | Plugs, socket-outlets and couplers for industrial purposes - Part 1: General requirements |
ISO 2867:2011 | Earth-moving machinery Access systems |
ISO 13849-1:2015 | Safety of machinery — Safety-related parts of control systems — Part 1: General principles for design |
IEC 61000-6-2 : 3.0:2016 | ELECTROMAGNETIC COMPATIBILITY (EMC) - PART 6-2: GENERIC STANDARDS - IMMUNITY STANDARD FOR INDUSTRIAL ENVIRONMENTS |
IEC 60664-1:2007 | Insulation coordination for equipment within low-voltage systems - Part 1: Principles, requirements and tests |
IEC 61851-1:2017 | Electric vehicle conductive charging system - Part 1: General requirements |
IEC 62271-102:2001+AMD1:2011+AMD2:2013 CSV | High-voltage switchgear and controlgear - Part 102: Alternatingcurrent disconnectors and earthing switches |
IEC 60364-5-52:2009 | Low-voltage electrical installations - Part 5-52: Selection and erection of electrical equipment - Wiring systems |
ISO 10968:2004 | Earth-moving machinery Operator's controls |
IEC 62196-1:2014 | Plugs, socket-outlets, vehicle connectors and vehicle inlets - Conductive charging of electric vehicles - Part 1: General requirements |
IEC 61557-3:2007 | Electrical safety in low voltage distribution systems up to 1 000 V a.c. and 1 500 V d.c. - Equipment for testing, measuring or monitoring of protective measures - Part 3: Loop impedance |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.