ACI 301M : 2016
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
05-17-2023
English
07-01-2016
SECTION 1 - GENERAL REQUIREMENTS
SECTION 2 - FORMWORK AND FORMWORK ACCESSORIES
SECTION 3 - REINFORCEMENT AND REINFORCEMENT SUPPORTS
SECTION 4 - CONCRETE MIXTURES
SECTION 5 - HANDLING, PLACING, AND CONSTRUCTING
SECTION 6 - ARCHITECTURAL CONCRETE
SECTION 7 - LIGHTWEIGHT CONCRETE
SECTION 8 - MASS CONCRETE
SECTION 9 - POST-TENSIONED CONCRETE
SECTION 10 - SHRINKAGE-COMPENSATING CONCRETE FOR
INTERIOR SLABS
SECTION 11 - INDUSTRIAL FLOOR SLABS
SECTION 12 - TILT-UP CONSTRUCTION
SECTION 13 - PRECAST STRUCTURAL CONCRETE
SECTION 14 - PRECAST ARCHITECTURAL CONCRETE
NOTES TO SPECIFIER (Nonmandatory)
This is a Reference Specification that the Architect/Engineer can apply to any construction project involving structural concrete by citing it in the Project Specifications.
Committee |
301
|
DevelopmentNote |
METRIC VERSION. (12/2009)
|
DocumentType |
Standard
|
Pages |
68
|
PublisherName |
American Concrete Institute
|
Status |
Superseded
|
SupersededBy | |
Supersedes |
ACI 363R : 2010 | REPORT ON HIGH-STRENGTH CONCRETE |
ANSI/AWWA D110:2013(R2018) | WIRE- AND STRAND-WOUND, CIRCULAR, PRESTRESSED CONCRETE WATER TANKS |
PIP STS02465 : 2012 | AUGERED CAST-IN-PLACE PILES INSTALLATION SPECIFICATION |
ACI 440.5M : 2008 | SPECIFICATION FOR CONSTRUCTION WITH FIBER-REINFORCED POLYMER REINFORCING BARS |
ACI 346M : 2009 | SPECIFICATION FOR CAST-IN-PLACE CONCRETE PIPE - METRIC |
ACI 351.4M : 2014 | SPECIFICATION FOR INSTALLATION OF CEMENTITIOUS GROUTING BETWEEN FOUNDATIONS AND EQUIPMENT BASES (METRIC) |
ACI 117M : 2010 | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
ACI 305.1M : 2014 | SPECIFICATION FOR HOT WEATHER CONCRETING (METRIC) |
CSA S269.1 : 2016 | FALSEWORK AND FORMWORK |
ACI 117:2010(R2015) | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
ACI 330.1M : 2014 | SPECIFICATION FOR UNREINFORCED CONCRETE PARKING LOTS AND SITE PAVING (METRIC) |
ACI E3 : 2013 | CEMENTITIOUS MATERIALS FOR CONCRETE |
ACI 117:2010 | SPECIFICATION FOR TOLERANCES FOR CONCRETE CONSTRUCTION AND MATERIALS AND COMMENTARY |
ACI 305.1 : 2014 | SPECIFICATION FOR HOT WEATHER CONCRETING |
ACI 351.5M : 2015 | SPECIFICATION FOR INSTALLATION OF EPOXY GROUT BETWEEN FOUNDATIONS AND EQUIPMENT BASES (METRIC) |
ACI 330.1 : 2014 | SPECIFICATION FOR UNREINFORCED CONCRETE PARKING LOTS AND SITE PAVING |
ASTM C 1778 : 2016 : REDLINE | Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete |
ASTM D 98 : 2015 : REDLINE | Standard Specification for Calcium Chloride |
AASHTO M 182 : 2005(R2017) | SPECIFICATION FOR BURLAP CLOTH MADE FROM JUTE OR KENAF AND COTTON MATS |
ASTM A 615/A615M : 2016-03 | SPECIFICATION FOR DEFORMED AND PLAIN CARBON-STEEL BARS FOR CONCRETE REINFORCEMENT |
ASTM C 900 : 2015 : REDLINE | Standard Test Method for Pullout Strength of Hardened Concrete |
ASTM A 675/A675M : 2014 : REDLINE | Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality, Mechanical Properties |
ANSI A118.6 : 1992 | SPECIFICATIONS FOR CERAMIC TILE GROUTS |
ASTM C 1157/C1157M : 2017 : REDLINE | Standard Performance Specification for Hydraulic Cement |
ASTM A 47/A47M : 1999 | Standard Specification for Ferritic Malleable Iron Castings |
ASTM C 873/C873M : 2015 : REDLINE | Standard Test Method for Compressive Strength of Concrete Cylinders Cast in Place in Cylindrical Molds |
ASTM C 150/C150M : 2017-04 | SPECIFICATION FOR PORTLAND CEMENT |
ASTM A 123/A123M : 2017 : REDLINE | Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products |
ASTM C 1315 : 2011 : REDLINE | Standard Specification for Liquid Membrane-Forming Compounds Having Special Properties for Curing and Sealing Concrete |
ASTM C 171 : 2016 : REDLINE | Standard Specification for Sheet Materials for Curing Concrete |
ASTM F 593 : 2017 : REDLINE | Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs |
ASTM D 2940/D2940M : 2015 : REDLINE | Standard Specification for Graded Aggregate Material For Bases or Subbases for Highways or Airports |
AWS C5.4 : 1993 | RECOMMENDED PRACTICES FOR STUD WELDING |
ASTM A 706/A706M : 2016 : REDLINE | Standard Specification for Deformed and Plain Low-Alloy Steel Bars for Concrete Reinforcement |
ASTM A 666 : 2015 : REDLINE | Standard Specification for Annealed or Cold-Worked Austenitic Stainless Steel Sheet, Strip, Plate, and Flat Bar |
ASTM C 979/C979M : 2016 : REDLINE | Standard Specification for Pigments for Integrally Colored Concrete |
ASTM C 1240 : 2015 : REDLINE | Standard Specification for Silica Fume Used in Cementitious Mixtures |
ASTM E 1745 : 2017 : REDLINE | Standard Specification for Plastic Water Vapor Retarders Used in Contact with Soil or Granular Fill under Concrete Slabs |
ASTM A 1055/A1055M : 2016 : REDLINE | Standard Specification for Zinc and Epoxy Dual-Coated Steel Reinforcing Bars |
ASTM C 642 : 2013 : REDLINE | Standard Test Method for Density, Absorption, and Voids in Hardened Concrete |
ACI ITG-7 : 2009 | SPECIFICATION FOR TOLERANCES FOR PRECAST CONCRETE |
ASTM C 1567 : 2013 : REDLINE | Standard Test Method for Determining the Potential Alkali-Silica Reactivity of Combinations of Cementitious Materials and Aggregate (Accelerated Mortar-Bar Method) |
ASTM C 42/C 42M : 2016-10 | TEST METHOD FOR OBTAINING AND TESTING DRILLED CORES AND SAWED BEAMS OF CONCRETE |
ASTM D 698 : 2013-05 | TEST METHODS FOR LABORATORY COMPACTION CHARACTERISTICS OF SOIL USING STANDARD EFFORT (12400 FT-LBF/FT[3] (600 KN-M/M[3])) |
ASTM C 1077 : 2017 : REDLINE | Standard Practice for Agencies Testing Concrete and Concrete Aggregates for Use in Construction and Criteria for Testing Agency Evaluation |
ASTM D 4060 : 2014 : REDLINE | Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser |
ANSI A118.4 : 1992 | SPECIFICATIONS FOR LATEX PORTLAND CEMENT MORTAR |
ASTM C 192/C192M : 2016-04 | PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY |
ASTM C 666/C666M : 2015 : REDLINE | Standard Test Method for Resistance of Concrete to Rapid Freezing and Thawing |
AWS D1.6/D1.6M : 2007 | STRUCTURAL WELDING CODE - STAINLESS STEEL |
AWS D1.4/D1.4M : 2011 | STRUCTURAL WELDING CODE - REINFORCING STEEL |
ASTM A 563 : 2015 : REDLINE | Standard Specification for Carbon and Alloy Steel Nuts |
ASTM C 309 : 2011 : REDLINE | Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete |
ASTM C 173/C173M : 2016 : REDLINE | Standard Test Method for Air Content of Freshly Mixed Concrete by the Volumetric Method |
ACI 216.1 : 2014 | CODE REQUIREMENTS FOR DETERMINING FIRE RESISTANCE OF CONCRETE AND MASONRY CONSTRUCTION ASSEMBLIES |
MIL C 882 : E | CLOTH, DUCK, COTTON OR COTTON POLYESTER BLEND, SYNTHETIC RUBBER,IMPREGNATED, LAMINATED, OIL RESISTANT |
ASTM C 172/C172M : 2017 : REDLINE | Standard Practice for Sampling Freshly Mixed Concrete |
ASTM C 834 : 2017 : REDLINE | Standard Specification for Latex Sealants |
ASTM C 597 : 2016 : REDLINE | Standard Test Method for Pulse Velocity Through Concrete |
ANSI A118.1 : 1999 | SPECIFICATIONS FOR DRY-SET PORTLAND CEMENT MORTAR |
ASTM A 996/A996M : 2016 : REDLINE | Standard Specification for Rail-Steel and Axle-Steel Deformed Bars for Concrete Reinforcement |
ASTM A 421/A421M : 2015 : REDLINE | Standard Specification for Stress-Relieved Steel Wire for Prestressed Concrete |
ASTM D 4397 : 2016 : REDLINE | Standard Specification for Polyethylene Sheeting for Construction, Industrial, and Agricultural Applications |
ASTM E 1155 : 2014 : REDLINE | Standard Test Method for Determining <emph type="ital">F<inf>F</inf></emph> Floor Flatness and <emph type="ital">F<inf>L</inf></emph> Floor Levelness Numbers |
ASTM C 1218/C1218M : 2017 : REDLINE | Standard Test Method for Water-Soluble Chloride in Mortar and Concrete |
ASTM C 157/C157M : 2017 : REDLINE | Standard Test Method for Length Change of Hardened Hydraulic-Cement Mortar and Concrete |
ASTM D 1621 : 2016 : REDLINE | Standard Test Method for Compressive Properties of Rigid Cellular Plastics |
ASTM A 276/A276M : 2017 : REDLINE | Standard Specification for Stainless Steel Bars and Shapes |
AWS D1.1/D1.1M : 2015 | STRUCTURAL WELDING CODE-STEEL |
ASTM A 779/A779M : 2016 : REDLINE | Standard Specification for Steel Strand, Seven-Wire, Uncoated, Compacted for Prestressed Concrete |
ASTM C 1064/C1064M : 2017 : REDLINE | Standard Test Method for Temperature of Freshly Mixed Hydraulic-Cement Concrete |
ASTM C 494/C494M : 2017 : REDLINE | Standard Specification for Chemical Admixtures for Concrete |
AASHTO M 251 : 2006 | SPECIFICATION FOR PLAIN AND LAMINATED ELASTOMERIC BRIDGE BEARINGS |
ASTM A 184/A184M : 2017 : REDLINE | Standard Specification for Welded Deformed Steel Bar Mats for Concrete Reinforcement |
ASTM D 638 : 2014 : REDLINE | Standard Test Method for Tensile Properties of Plastics |
ASTM C 567/C567M : 2014 : REDLINE | Standard Test Method for Determining Density of Structural Lightweight Concrete |
ACI 423.7 : 2014 | SPECIFICATION FOR UNBONDED SINGLE-STRAND TENDON MATERIALS |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.