• There are no items in your cart

AS 1627.2-1989

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Metal finishing - Preparation and pretreatment of surfaces - Power tool cleaning
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Language(s)

English

Published date

01-01-1989

Preview

1 - AS 1627.2-1989 METAL FINISHING - PREPARATION AND PRETREATMENT OF SURFACES - POWER TOOL CLEANING
4 - PREFACE
4 - CONTENTS
5 - FOREWORD
6 - SECTION 1. SCOPE AND GENERAL
6 - 1.1 SCOPE.
6 - 1.2 REFERENCED DOCUMENTS.
6 - 1.3 DEFINITIONS.
6 - 1.3.1 Bright steel
6 - 1.3.2 Detrimental burnishing
6 - 1.3.3 Power tool cleaning
6 - 1.3.4 Visible millscale
6 - 1.3.5 Visible rust
6 - 1.4 SURFACE REQUIREMENTS.
8 - SECTION 2. METHODS OF OPERATION
8 - 2.1 GENERAL.
8 - 2.2 EQUIPMENT.
8 - 2.3 PRELIMINARY CLEANING.
8 - 2.4 PROCEDURE FOR POWER TOOL CLEANING.
8 - 2.4.1 Fabricated metal sections prior to erection
8 - 2.4.2 Existing structures.
8 - 2.5 FINAL CLEANING.
8 - 2.6 SAFETY PRECAUTIONS.
8 - 2.6.1 Health hazards.
8 - 2.6.2 Face and eye protection.
8 - 2.6.3 Respiratory protection.
8 - 2.6.4 Safe working guidelines.
8 - 2.6.5 Atmosphere.
8 - 2.6.6 Ventilation.
10 - APPENDIX A - PURCHASING GUIDELINES
10 - A1 GENERAL.
10 - A2 INFORMATION TO BE SUPPLIED BY THE PURCHASER.

Describes the procedure and equipment required for preparing new, corroded and previously painted surfaces by removing loose mill scale, rust and paint with power impact tools, grinders, sanders, or wire brushes. Classifies the degrees of surface preparation.

This Standard sets out procedures and equipment recommended for the removal by use of power driven tools of visible rust, millscale, corrosion products and loose or flaky paint prior to painting or repainting. The Standard also sets out standards of surface preparation.NOTE: Appendix A contains advice and recommendations on information which should be supplied by the purchaser at the time of enquiry or order.

Committee
MT-009
DocumentType
Standard
ISBN
0 7262 5383 9
Pages
5
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Under Revision See DR 02008 CP

AS 1627.0-1997 Metal finishing - Preparation and pretreatment of surfaces Method selection guide (Reconfirmed 2017)
AS/NZS 1518:2002 External extruded high-density polyethylene coating system for pipes (Reconfirmed 2016)
AS 3978-1991 Non-destructive testing - Visual inspection of metal products and components
AS 4321-2001 Fusion-bonded medium-density polyethylene coating and lining for pipes and fittings (Reconfirmed 2019)
AS 2518-1992 Fusion-bonded low-density polyethylene coating for pipes and fittings
AS/NZS 3750.4:1994 Paints for steel structures Bitumen paint (Reconfirmed 2013)
AS 1627.5-1994 Metal finishing - Preparation and pretreatment of surfaces - Pickling, descaling and oxide removal
AS 4361.1-1995 Guide to lead paint management - Industrial applications
AS 4321-1995 Fusion-bonded medium-density polyethylene coating and lining for pipes and fittings
AS 3750.1-1994 Paints for steel structures - Epoxy mastic (two-pack) - For rusted steel
AS/NZS 2312:1994 Guide to the protection of iron and steel against exterior atmospheric corrosion
AS/NZS 3894.6:1996 Site testing of protective coatings Determination of residual contaminants
AS 4025.4-1994 Paints for equipment including ships Solvent-borne - Lead and chromate free - Anticorrosive metal primer

View more information
US$15.94
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.