AS 1910-2004 (R2016)

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

RECONFIRMATION NOTICETechnical Committee WS-001 has reviewed the content of this publication and in accordance with Standards Australia procedures for reconfirmation, it has been determined that the publication is still valid and does not require change.Certain documents referenced in the publication may have been amended since the original date of publication. Users are advised to ensure that they are using the latest versions of such documents as appropriate, unless advised otherwise in this Reconfirmation Notice.Approved for reconfirmation in accordance with Standards Australia procedures for reconfirmation on 3 September 2015.The following are represented on Technical Committee WS-001:Association of Accredited Certification BodiesAustralian Industry GroupBuilding Officials Institute of New ZealandCSIROGas Technical Regulators CommitteeHousing Industry AssociationNational Association of Testing Authorities AustraliaPlastics Industry Pipe Association of AustraliaPlastics New ZealandPlumbing Distributors Association of New ZealandPlumbing Products Industry GroupQueensland Brassware AssociationThe Institute of Plumbing AustraliaWater Services Association of Australia

Scope - (Show below) - (Hide below)

This Standard specifies requirements for active float control valves for use in water supply systems where the normal working temperature does not exceed 95°C and the continuous working pressure extends up to a maximum of 1.4 MPa for a range of nominal sizes from DN 6 to DN 80.This Standard does not cover WC cistern flushing valves.NOTE: WC cistern flushing valves are covered in all parts of AS 1172. Means of demonstrating compliance with this Standard are set out in Appendix A.

General Product Information - (Show below) - (Hide below)

Published
Document Type	Standard
Status	Current
Publisher	Standards Australia
ProductNote	Reconfirmed 03/06/2016. This standard has been reconfirmed in Australia in 2016 and remains current in New Zealand. Reconfirmation Notice 03/06/2016
Pages
ISBN
Committee	WS-001
Under Revision	DR 06072 CP
Supersedes	DR 03484 AS 1910-1994

History - (Show below) - (Hide below)

First published as AS 1910-1976.
Second edition 1994.
Third edition 2004.
Reconfirmed 2016.

Standards Referenced By This Book - (Show below) - (Hide below)

AS 3558.24-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to hot liquids of the surface of sinks
AS 1172.2-1999	Water closet (WC) pans of 6/3 L capacity or proven equivalent Cisterns
AS 3558.7-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of impact resistance of laundry troughs
AS 1722.2-1992 (R2017)	Pipe threads of Whitworth form Fastening pipe threads
AS 1565-1996	Copper and copper alloys - Ingots and castings
AS 3558.1-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing and fixtures Determination of water absorption characteristics
AS 2345-1992	Dezincification resistance of copper alloys
AS 2074-2003	Cast steels
AS 1567-1985	Copper and copper alloys - Wrought rods, bars and sections
AS 3688-2005	Water supply - Metallic fittings and end connectors
AS 1172.1-1993	Water closets of 6/3 L capacity Pans
AS 3558.12-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to thermal shock of baths for ablutionary purposes
AS 1172-1989	Water closet pans
AS 3558.18-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to thermal shock of shower bases and shower modules
AS 3558.15-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of impact resistance of washbasins
AS 3558.21-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal expansion under load of sinks
AS 3558.14-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal expansion under load of baths for ablutionary purposes
AS/NZS 1567:1997	Copper and copper alloys - Wrought rods, bars and sections
AS 3558.8-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to thermal shock of laundry troughs
AS 3558.0-1989	Methods of testing plastics and composite materials sanitary plumbing fixtures Introduction and list of methods
AS 3558.11-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of impact resistance of baths for ablutionary purposes
AS 1834.1-1991 (R2018)	Material for soldering Solder alloys
AS 3558.19-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of impact resistance of sinks
AS/NZS 4020:2005	Testing of products for use in contact with drinking water
AS 3558.16-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to thermal shock of washbasins
AS 1722.1-1975	Pipe threads of Whitworth form Sealing pipe threads
AS 1568-1985	Copper and copper alloys - Forging stock and forgings
AS/NZS 3500.0:2003	Plumbing and drainage Glossary of terms
AS 2738-2000 (R2018)	Copper and copper alloys - Compositions and designations of refinery products, wrought products, ingots and castings
AS 3558.10-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal expansion under load of laundry troughs
AS 3688-1994	Water supply - Copper and copper alloy body compression and capillary fittings and threaded-end connectors
AS 3558.5-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of degradation by ultraviolet light
AS 3558.6-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Visual examination of surface finish for defects
AS 2345-2006 (R2016)	Dezincification resistance of copper alloys
AS 3558.9-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal distortion of laundry troughs
AS/NZS 3500.1:2003	Plumbing and drainage Water services
AS 3558.3-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of colour fastness
AS/NZS 4020:2002	Testing of products for use in contact with drinking water
AS 3558.23-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to heat of the surface of sinks
AS 1572-1998 (R2018)	Copper and copper alloys - Seamless tubes for engineering purposes
AS 3558.20-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to thermal shock of sinks
AS 3558.2-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of chemical and stain resistance
AS 3558.13-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal distortion of baths for ablutionary purposes
AS 2136-1977 (R2018)	Method for detecting the susceptibility of copper and its alloys to stress corrosion cracking using the mercurous nitrate test
AS 1881-1986 (R2018)	Zinc alloys - Casting ingots and castings - Quality requirements
AS 1167.1-1993	Welding and brazing - Filler metals Filler metal for brazing and braze welding
AS 3558.22-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of thermal distortion of sinks
AS 3558.4-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of resistance to surface scratching
AS/NZS 1568:1998	Copper and copper alloys - Forging stock and forgings
AS 1432-2004 (R2016)	Copper tubes for plumbing, gasfitting and drainage applications
AS/NZS 1167.1:2005	Welding and brazing - Filler metals Filler metal for brazing and braze welding
AS 3558.17-1999 (R2016)	Methods of testing plastics and composite materials sanitary plumbing fixtures Determination of impact resistance of shower bases and shower modules

Standards Referencing This Book - (Show below) - (Hide below)

AS/NZS 3500.4:2015	Plumbing and drainage Heated water services
AS 5200.000-2006 (R2018)	Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
AS/NZS 3500.4:2003	Plumbing and drainage Heated water services
MP 52-2005	Manual of authorization procedures for plumbing and drainage products
AS 1361-1995 (R2016)	Electric heat-exchange water heaters - For domestic applications
AS 5200.000-2005	Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
AS/NZS 3500.4:2018	Plumbing and drainage Heated water services (Amendment 1 included)

Table of Contents - (Show below) - (Hide below)

Abstract - (Show below) - (Hide below)

Scope - (Show below) - (Hide below)

General Product Information - (Show below) - (Hide below)

History - (Show below) - (Hide below)

Standards Referenced By This Book - (Show below) - (Hide below)

Standards Referencing This Book - (Show below) - (Hide below)

Add To Cart

Publisher

Category

Sub Category

Access your standards online with a subscription?