• There are no items in your cart

AS/NZS 1260:2002

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

PVC-U pipes and fittings for drain, waste and vent application
Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

06-30-2017

Language(s)

English

Published date

08-01-2002

Preview

1 - AS/NZS 1260:2002 PVC-U PIPES AND FITTINGS FOR DRAIN, WASTE AND VENT APPLICATION
4 - PREFACE
5 - CONTENTS
7 - SECTION 1 SCOPE AND GENERAL
7 - 1.1 SCOPE
7 - 1.2 REFERENCED DOCUMENTS
8 - 1.3 DEFINITIONS
8 - 1.3.1 Effective seal
8 - 1.3.2 Effective sealing length
8 - 1.3.3 Fabricated fitting/assembly
9 - 1.3.4 Inside wall thickness
9 - 1.3.5 Maximum differential displacement
9 - 1.3.6 Minimum jointing compression conditions
9 - 1.3.7 Moulded fitting
9 - 1.3.8 Out-of-roundness (sometimes referred to as ovality)
9 - 1.3.9 Plain wall construction
9 - 1.3.10 Recycled PVC-U (Recyclate)
9 - 1.3.11 Ribbed or hollow profile construction
9 - 1.3.12 Sandwich construction
9 - 1.3.13 Sharp edge
9 - 1.3.14 Structured wall
9 - 1.4 RING BENDING STIFFNESS
10 - 1.5 NOTATION
10 - 1.6 CLASSIFICATION
12 - SECTION 2 GENERAL REQUIREMENTS
12 - 2.1 GENERAL
12 - 2.2 COMPOSITION
12 - 2.3 COLOUR
12 - 2.4 FREEDOM FROM DEFECTS
12 - 2.4.1 General
12 - 2.4.2 Spigot ends
13 - 2.5 REQUIREMENTS FOR ELASTOMERIC SEALS
13 - 2.6 SOLVENT CEMENTS
13 - 2.7 PACKAGING, STORAGE AND TRANSPORTATION
14 - SECTION 3 PERFORMANCE REQUIREMENTS
14 - 3.1 GENERAL
14 - 3.2 TESTS ON PIPES
14 - 3.2.1 Pipe impact characteristics at 20°C
14 - 3.2.2 Reversion (for plain wall pipes only)
14 - 3.2.3 Bond strength (for hollow profile wall pipes only)
14 - 3.2.4 Pipe stiffness
15 - 3.2.5 Ring flexibility test (for structured wall pipes only)
15 - 3.2.6 Softening temperature (Vicat test)
15 - 3.2.7 Elevated temperature cycling test on structured wall pipes (applicable up to and including size DN 80)
15 - 3.3 TESTS ON MOULDED AND FABRICATED FITTINGS
15 - 3.3.1 Hydrostatic pressure test (applicable only to fittings with inspection or test openings and to fabricated fittings)
15 - 3.3.2 Hydrostatic pressure test (applicable to pan connectors)
15 - 3.3.3 Liquid infiltration test (applicable only to fittings with inspection or test openings)
15 - 3.3.4 High temperature stress relief test (applicable only to injection-moulded fittings)
16 - 3.3.5 Softening temperature (Vicat test)
16 - 3.3.6 Stiffness (for structured and hollow profile wall fittings only)
16 - 3.3.7 Elevated temperature cycling test on structured wall fittings (applicable up to and including size DN80)
16 - 3.4 TESTS ON ELASTOMERIC SEAL JOINTS
16 - 3.4.1 General
16 - 3.4.2 Hydrostatic pressure test
16 - 3.4.3 Liquid infiltration test
16 - 3.4.4 Contact width and pressure
16 - 3.5 ADDITIONAL TESTS ON PIPE AND FITTINGS CONTAINING RECYCLED PVC-U
16 - 3.5.1 Flattening test
16 - 3.5.2 Pipe high temperature test (Not applicable to intermediate layers of pipes of sandwich construction)
17 - SECTION 4 PIPES
17 - 4.1 GENERAL
17 - 4.2 DIAMETER AND WALL THICKNESS
17 - 4.3 LENGTH
17 - 4.4 PIPE SPIGOT ENDS
17 - 4.5 SOCKETS FORMED ON PIPE ENDS
21 - 4.6 MARKING
22 - 4.7 WITNESS MARK
23 - SECTION 5 MOULDED FITTINGS
23 - 5.1 GENERAL
23 - 5.2 DIMENSIONS OF MOULDED FITTINGS
23 - 5.2.1 General
23 - 5.2.2 Spigot ends
23 - 5.2.3 Sockets on moulded fittings
25 - 5.2.4 Tapered spigot ends for solvent cement jointing
25 - 5.3 WALL THICKNESS
26 - 5.4 GEOMETRY OF FITTINGS
26 - 5.4.1 Clear bore
27 - 5.4.2 Sweep junctions and bends
27 - 5.4.3 Eccentric tapers
27 - 5.4.4 Gullies
28 - 5.4.5 Vented bends
28 - 5.4.6 Pan connectors
28 - 5.5 THREADED END CONNECTIONS
28 - 5.6 TEST OPENINGS
28 - 5.6.1 General
29 - 5.6.2 Doors or insert plugs
29 - 5.6.3 Threaded caps
29 - 5.7 INSPECTION OPENINGS
31 - 5.8 GRATINGS
31 - 5.9 BOLTED TRAP SCREWS
31 - 5.10 OVERFLOW RELIEF GRATINGS
31 - 5.10.1 Outlet
31 - 5.10.2 Inlet
32 - 5.11 MARKING
33 - SECTION 6 FABRICATED FITTINGS
33 - 6.1 GENERAL
33 - 6.2 MATERIALS
33 - 6.3 COMPLIANCE
33 - 6.4 MARKING
34 - SECTION 7 ELASTOMERIC SEAL JOINTS
34 - 7.1 GENERAL
34 - 7.2 DESIGN
34 - 7.3 EFFECTIVE SEALING LENGTH
36 - APPENDIX A - MEANS FOR DEMONSTRATING COMPLIANCE WITH THIS STANDARD
36 - A1 SCOPE
36 - A2 RELEVANCE
36 - A3 BATCH
36 - A3.1 Acceptable quality level (AQL)
36 - A3.2 Batch
36 - A3.3 Batch release test
36 - A3.4 Inspection level
36 - A3.5 Lot
36 - A3.6 New formulation
37 - A3.7 Process verification test (PVT)
37 - A3.8 Sample
37 - A3.9 Sampling plan
37 - A3.10 Type test (TT)
37 - A4 PRODUCT CERTIFICATION
37 - A5 MINIMUM SAMPLING AND TESTING FREQUENCY PLAN
37 - A5.1 General
37 - A5.2 Retesting
38 - A5.3 Rejection after test
40 - A6 NEW FORMULATION
41 - APPENDIX B - TYPICAL RANGE OF MOULDED FITTINGS FOR DWV APPLICATIONS

States requirements for PVC pipes and fittings for sewer, drain, waste and vent applications above-ground or below ground and intended to be used where the pipeline is operating under gravity flow and the operating pressure is low.

This Standard specifies requirements for PVCU pipes and fittings for sewer, drain, waste and vent applications above-ground or below ground and intended to be used where the pipeline is operating under gravity flow and the operating pressure is low. The Standard includes requirements for both plain and structured wall pipes and fittings.NOTE: Pipes manufactured to this Standard should only be used and installed in accordance with AS 2032, AS/NZS 2566, AS 3500 and NZS 7643.Methods of demonstrating compliance with this Standard are given in Appendix A.

Committee
PL-021
DocumentType
Standard
ISBN
0 7337 4700 0
Pages
49
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

First published in Australia as part of AS K138-1963 and AS A160-1969.Second edition AS K138-1967.Third edition AS K138-1969.AS K138-1969 and part of AS A160-1969 revised, amalgamated and redesignated as AS 1415.1-1974.AS A160-1969 revised and redesignated in part as AS 1415.2-1974, AS 1415.3-1974, AS 1415.4-1974, and AS 1415.5-1974.Second edition AS 1415.1-1984.Second edition AS 1415.3-1984.AS 1415.2-1974 and AS 1415.4-1974 revised, amalgamated and redesignated as AS 1415.2-1984.AS 1415.5-1974 revised and redesignated as AS 1415.4-1984.AS 1260.1 first published 1974.AS 1260.2 first published 1974.AS 1260.3 first published 1974.AS 1260.4 first published 1974.AS 1260.5 first published 1974.AS 2340 first published 1980.AS 1260.1-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.1-1984.AS 1260.2-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.2-1984.Second edition AS 1260.3-1984.AS 1260.5-1974 revised and redesignated as AS 1260.4-1984.Second edition AS 1260.5-1993.First published in New Zealand in part as NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988.AS 1260.1-1984, AS 1260.2-1984, AS 1260.3-1984, AS 1260.4-1984, AS 1260.5-1993, AS 1415.1-1984, AS 1415.2-1984, AS 1415.3-1984, AS 1415.4-1984, AS 2340-1980, NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988 jointly revised, amalgamated and redesignated as AS/NZS 1260:1996.Second edition 1999.Third edition 2002. First published in Australia as part of AS K138-1963 and AS A160-1969. Second edition AS K138-1967. Third edition AS K138-1969. AS K138-1969 and part of AS A160-1969 revised, amalgamated and redesignated as AS 1415.1-1974. AS A160-1969 revised and redesignated in part as AS 1415.2-1974, AS 1415.3-1974, AS 1415.4-1974, and AS 1415.5-1974. Second edition AS 1415.1-1984. Second edition AS 1415.3-1984. AS 1415.2-1974 and AS 1415.4-1974 revised, amalgamated and redesignated as AS 1415.2-1984. AS 1415.5-1974 revised and redesignated as AS 1415.4-1984. AS 1260.1 first published 1974. AS 1260.2 first published 1974. AS 1260.3 first published 1974. AS 1260.4 first published 1974. AS 1260.5 first published 1974. AS 2340 first published 1980. AS 1260.1-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.1-1984. AS 1260.2-1974 and part of AS 1260.4-1974 revised, amalgamated and redesignated as AS 1260.2-1984. Second edition AS 1260.3-1984. AS 1260.5-1974 revised and redesignated as AS 1260.4-1984. Second edition AS 1260.5-1993. First published in New Zealand in part as NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988. AS 1260.1-1984, AS 1260.2-1984, AS 1260.3-1984, AS 1260.4-1984, AS 1260.5-1993, AS 1415.1-1984, AS 1415.2-1984, AS 1415.3-1984, AS 1415.4-1984, AS 2340-1980, NZS 7641:1978, NZS 7642:1971 and NZS 7649:1988 jointly revised, amalgamated and redesignated as AS/NZS 1260:1996. Second edition 1999. Third edition 2002.

AS/NZS 2566.1:1998 Buried flexible pipelines Structural design
AS/NZS 1462.3:1998 Methods of test for plastics pipes and fittings Method for determining the impact characteristics of pipes (Reconfirmed 2017)
AS/NZS 1462.4:2002 Methods of test for plastics pipes and fittings Method for determining reversion of plastics pipes (Reconfirmed 2017)
AS 1172.1-2005 Water closets (WC) Pans
AS/NZS 1462.2:1998 Methods of test for plastics pipes and fittings Method for determining the flattening properties of plastics pipes and fittings
AS/NZS 3500.0:1995 National Plumbing and Drainage Code Glossary of terms
AS 2887-1993 Plastic waste fittings
AS/NZS 1462.13(INT):2001 Methods of test for plastics pipes and fittings Method for the determination of elastomeric seal joint contact width and pressure
AS/NZS 3879:1995 Solvent cements and priming fluids for use with unplasticized PVC (uPVC) pipes and fittings
HB 18.28-2005 Conformity assessment - Guidance on a third-party certification system for products
AS/NZS 1462.22:1997 Methods of test for plastics pipes and fittings Method for determination of pipe stiffness
AS/NZS 1462.1:2006 Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings
AS/NZS 1462.23:1997 Methods of test for plastics pipes and fittings - Method for determination of ring flexibility
AS 1646-2007 Elastomeric seals for waterworks purposes (Reconfirmed 2018)
AS 1646.1-2000 Elastomeric seals for waterworks purposes - General requirements
AS/NZS 1462.2:2006 Methods of test for plastics pipes and fittings Method for determining the flattening properties of plastics pipes and fittings
AS 1172.1-1993 Water closets of 6/3 L capacity - Pans
AS/NZS 1462.16:2006 Methods of test for plastics pipes and fittings Method for high temperature testing of pipe (Reconfirmed 2017)
AS 1646.2-2000 Elastomeric seals for waterworks purposes Material requirements for pipe joint seals used in water and wastewater applications - Specifies by prescription formulation
AS 1646.3-2000 Elastomeric seals for waterworks purposes - Material requirements for pipe joints seals used in water and wastewater applications with the exception of natural rubber and polyisoprene compounds
AS/NZS 3500.0:2003 Plumbing and drainage Glossary of terms
AS/NZS 1477:1999 PVC pipes and fittings for pressure applications
AS/NZS 1462.11:1996 Methods of test for PVC pipes and fittings Method for high temperature stress-relief testing of fittings (Reconfirmed 2017)
AS 2032-1977 Code of practice for installation of UPVC pipe systems
AS 1199-1988 Sampling procedures and tables for inspection by attributes
AS/NZS 1462.21:1997 Methods of test for plastics pipes and fittings Method for determination of bond strength (Reconfirmed 2017)
AS/NZS 1462.23:2006 Methods of test for plastics pipes and fittings Method for determination of ring flexibility
AS/NZS 1462.16:1996 Methods of test for PVC pipes and fittings - Method for high temperature testing of pipe
AS/NZS 1462.8:1998 Methods of test for plastics pipes and fittings Method of test for infiltration
AS/NZS 1462.10:1998 Methods of test for plastics pipes and fittings Method for hydrostatic pressure testing of fittings and elastomeric seal joints for non-pressure applications (Reconfirmed 2017)
AS 2700-1996 Colour Standards for general purposes - Swatches
AS/NZS 3879:2006 Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS pipes and fittings
AS/NZS 1477:2006 PVC pipes and fittings for pressure applications
HB 18.28-1991 Guidelines for third-party certification and accreditation - Guide 28: General rules for a model third-party certification system for products
AS/NZS 1462.1:2001 Methods of test for plastics pipes and fittings Method for determining the dimensions of pipes and fittings

ATS 5200.006-2004 Technical Specification for plumbing and drainage products Reflux valves - sewerage
AS 3517-2007 Capillary fittings of copper and copper alloy for non-pressure sanitary plumbing applications (Reconfirmed 2018)
ATS 5200.499-2008 Technical Specification for plumbing and drainage products Inline sewer dosing unit (SDU)
AS 5200.000-2006 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products (Reconfirmed 2018)
ATS 5200.460-2005 Technical Specification for plumbing and drainage products Grey water diversion device (GWDD)
AS 5601-2004 Gas installations
AS 1646-2007 Elastomeric seals for waterworks purposes (Reconfirmed 2018)
ATS 5200.104-2005 Appliances (miscellaneous)
ATS 5200.055-2008 Technical specifications for plumbing and drainage products Plastics fittings - Connectors with flexible intermediate joints for drainage and sewerage applications
AS/NZS 4798(INT):2005 Polyethylene maintenance shafts
AS/NZS 4999:2006 PVC-U maintenance shafts
AS/NZS 3879:2006 Solvent cements and priming fluids for PVC (PVC-U and PVC-M) and ABS pipes and fittings
AS/NZS 4999(INT):2003 PVC-U maintenance shafts
AS/NZS 3500.4:2003 Plumbing and drainage Heated water services
AS/NZS 3500.2:2003 Plumbing and drainage Sanitary plumbing and drainage
AS/NZS 3500.2.2:1996 National plumbing and drainage Sanitary plumbing and drainage - Acceptable solutions
MP 52-2005 Manual of authorization procedures for plumbing and drainage products
AS 4809-2003 Copper pipe and fittings - Installation and commissioning
AS/NZS 3500.3:2003 Plumbing and drainage Stormwater drainage
ATS 5200.501-2009 Technical Specification for plumbing and drainage products Anti-infiltration overflow relief point
ATS 5200.101-2005 Appliances (low hazard rating)
AS 5200.000-2005 Technical specification for plumbing and drainage products Procedures for certification of plumbing and drainage products
ATS 5200.482-2006 Technical Specification for plumbing and drainage products Soil waste dump fitting
AS/NZS 1254:2002 PVC pipes and fittings for storm and surface water applications
ATS 5200.460-2004 Technical Specification for plumbing and drainage products Grey water diversion valve assembly
ATS 5200.006-2005 Technical Specification for plumbing and drainage products Reflux valves - Sewerage
AS/NZS 4327:1995 Metal-banded flexible couplings for low-pressure applications (Reconfirmed 2020)
AS/NZS 3500.1:2003 Plumbing and drainage Water services
AS 4072.1-2005 Components for the protection of openings in fire-resistant separating elements Service penetrations and control joints (Reconfirmed 2016)
AS 1589-2001 Copper and copper alloy waste fittings (Reconfirmed 2018)
AS/NZS 2032:2006 Installation of PVC pipe systems

View more information
US$118.31
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.