Customer Support: +1 416-401-8730

Login to i2i Subscription Intertek.com
  • There are no items in your cart
Please enter a keyword to search
Advanced search
Home
AS
AS/NZS 61347.2.10:2004

AS/NZS 61347.2.10:2004

Superseded

Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Lamp controlgear Particular requirements for electronic invertors and convertors for high-frequency operation of cold start tubular discharge lamps (neon tubes) (IEC 61347-2-10:2000 MOD)

Available format(s)

Hardcopy , PDF 1 User , PDF 3 Users , PDF 5 Users , PDF 9 Users

Superseded date

02-20-2019

Language(s)

English

Published date

05-13-2004

Publisher

Standards Australia

Preview

1 Scope2 Normative references3 Definitions4 General requirements5 General notes on tests6 Classification7 Marking 7.1 Item to be marked 7.2 Durability and legibility of marking8 Terminals, cords and cables9 Provisions for earthing10 Protection against accidental contact with live parts11 Moisture resistance and insulation12 Electric strength13 Thermal endurance test for windings14 Normal conditions15 Abnormal conditions16 Fault conditions17 Construction18 Creepage distances and clearances19 Protective circuits20 Screws, current-carrying parts and connections21 Resistance to heat, fire and tracking22 Resistance to corrosion23 No-load rated output voltage and rated output current 23.1 No-load rated output voltage 23.2 Rated output current 23.3 ComplianceAnnex A (normative) - Test to establish whether a conductive part is a live part which may cause an electric shockAnnex B (normative) - Particular requirements for thermally protected lamp controlgearAnnex C (normative) - Particular requirements for electronic lamp controlgear with means of protection against overheatingAnnex D (normative) - Requirements for carrying out the heating tests of thermally protected lamp controlgearAnnex E (normative) - Use of constant S other than 4500 in t[w] testsAnnex F (normative) - Draught-proof enclosureAnnex G (normative) - Explanation of the derivation of the values of pulse voltagesAnnex H (normative) - TestsAnnex I (normative) - Measurement of currents and voltages in the output circuits of electronic invertors or convertors for neon tubes

Specifies particular safety requirements for electronic invertors and convertors for high-frequency operation of tubular cold-cathode discharge lamps used in signs and luminous discharge tube installations.

This part of AS/NZS 61347 specifies particular requirements for electronic invertors and convertors for high-frequency operation of tubular cold-cathode discharge lamps used in signs and luminous discharge tube installations and operating with an output voltage exceeding 1 000 V but not exceeding 10 000 V for direct connection to supply voltages not exceeding 1 000 V at 50 Hz or 60 Hz or 1 000 V d.c. NOTE 1 In Japan, the output voltage of 15 000 V is acceptable. The requirements for two types of invertors and convertors, types A and B, are specified as follows: Type A unit: an invertor or convertor operating within the frequency range 20 kHz to 50 kHz, and having an output voltage (between terminals) not exceeding 5 000 V peak, a maximum output current limited to 35 mA (r.m.s.) and 50 mA (peak value). The supply voltage does not exceed 250 V at 50 Hz or 60 Hz or 250 V d.c. NOTE 2 The output current of a type A unit may be considered as not presenting an electric shock hazard due to the limits on the current and frequency range. NOTE 3 In Japan, the output voltage of 15 000 V is acceptable. Type B unit: an invertor or convertor having a no-load output voltage not exceeding 5 000 V to earth or 10 000 V between terminals, operating within the frequency range 10 kHz to 100 kHz with a maximum output current limited to 200 mA (r.m.s.) and 400 mA (peak value). NOTE 4 Type B units require additional protection in the output circuit. NOTE 5 In Japan, a type B unit exceeding 50 mA and/or the secondary grounded is not acceptable. In order to check the safety of invertors or convertors, it is necessary to check their performance. However, since no standardization of the characteristics of neon tubes exists, reference loads are specified in this standard to ensure reproducible test results.The rated maximum operating temperature of the winding, tw, is not applicable to thisstandard.

Committee
EL-041
DocumentType
Standard
ISBN
0 7337 5961 0
Pages
15
PublisherName
Standards Australia
Status
Superseded
SupersededBy
Supersedes
UnderRevision

Standards Relationship
IEC 61347-2-10:2000+AMD1:2008 CSV Identical

First published as AS/NZS 61347.2.10:2004.

AS/NZS 61347.1:2002 Lamp controlgear General and safety requirements (IEC 61347-1:2000, MOD)

AS/NZS IEC 61347.2.13:2013 Lamp controlgear Particular requirements for d.c. or a.c. supplied electronic controlgear for LED modules (IEC 61347-2-13, Ed.1.0 (2006) MOD)
AS/NZS 60079.15:2011 Explosive atmospheres Equipment protection by type of protection 'n'

View more information
US$69.34
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF 1 User - English
PDF 3 Users - English
PDF 5 Users - English
PDF 9 Users - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.

Learn more on subscription solutions

or

Get in touch with us