• There are no items in your cart

ASTM A 285/A285M : 2017 : REDLINE

Current
Current

The latest, up-to-date edition.

Standard Specification for Pressure Vessel Plates, Carbon Steel, Low- and Intermediate-Tensile Strength
Available format(s)

PDF

Language(s)

English

Published date

11-03-2017

CONTAINED IN VOL. 01.04, 2017 Defines carbon steel plates of low- and intermediate-tensile strengths which may be made by killed, semi-killed, capped, or rimmed steel practices at the producer's option.

1.1This specification2 covers carbon steel plates of low- and intermediate-tensile strengths which may be killed or semi-killed at the producer’s option. These plates are intended for fusion-welded pressure vessels.

1.2Plates under this specification are available in three grades having different strength levels as follows:

Grade

Tensile Strength, ksi [MPa]

A

45–65 [310–450]

B

50–70 [345–485]

C

55–75 [380–515]

1.3The maximum thickness of plates is limited by the capacity of the composition to meet the specified mechanical property requirements.

Note 1:For killed carbon steels only, refer to the following ASTM specifications:3

A299/A299M Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon

A515/A515M Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service

A516/A516M Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service

1.4For plates produced from coil and furnished without heat treatment or with stress relieving only, the additional requirements, including additional testing requirements and the reporting of additional test results, of Specification A20/A20M apply.

1.5The values stated in either inch-pound units or SI units are to be regarded separately as standard. Within the text, the SI units are shown in brackets. The values stated in each system are not exact equivalents; therefore, each system must be used independently of the other. Combining values from the two systems may result in nonconformance with the specification.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
A 01
DevelopmentNote
Supersedes ASTM A 285 (10/2001) Supersedes ASTM A 89 (02/2002)
DocumentType
Redline
Pages
4
PublisherName
American Society for Testing and Materials
Status
Current
Supersedes

AWS A5.4 : 92(R2000) STAINLESS STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING, SPECIFICATION FOR
API 12D CHINESE : 2008 SPECIFICATION FOR FIELD WELDED TANKS FOR STORAGE OF PRODUCTION LIQUIDS
AWS A5.28/A5.28M : 2005 : R2015 SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND RODS FOR GAS SHIELDED ARC WELDING
AWS A5.13 : 2000 SOLID SURFACING WELDING RODS AND ELECTRODES, SPECIFICATION FOR,
NACE RP 02 96 : 2004 GUIDELINES FOR DETECTION, REPAIR, AND MITIGATION OF CRACKING OF EXISTING PETROLEUM REFINERY PRESSURE VESSELS IN WET H[2]S ENVIRONMENTS
AWS A5.28/A5.28M : 2005 : INC : ERR 1 SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND RODS FOR GAS SHIELDED ARC WELDING
AWS A5.21/A5.21M:2011 SPECIFICATION FOR BARE ELECTRODES AND RODS FOR SURFACING
AWS A5.23/A5.23M : 2011 SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES AND FLUXES FOR SUBMERGED ARC WELDING
AWS A5.13/A5.13M : 2010 SPECIFICATION FOR SURFACING ELECTRODES FOR SHIELDED METAL ARC WELDING
AWS A5.21 : 2001 SPECIFICATION FOR BARE ELECTRODES AND RODS FOR SURFACING
AWS A5.20/A5.20M : 2005 SPECIFICATION FOR CARBON STEEL ELECTRODES FOR FLUX CORED ARC WELDING
ISO 21172-1:2015 Gas cylinders Welded steel pressure drums up to 3 000 litres capacity for the transport of gases Design and construction Part 1: Capacities up to 1 000 litres
ASTM A 134 : 1996 : R2012 Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
ASTM A 134 : 1996 : R2001 Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
BS EN ISO 10439:2002 Petroleum, chemical and gas service industries. Centrifugal compressors
I.S. EN ISO 10439:2002 PETROLEUM, CHEMICAL AND GAS SERVICE INDUSTRIES - CENTRIFUGAL COMPRESSORS
ASTM C 868 : 2002 : R2012 Standard Test Method for Chemical Resistance of Protective Linings (Withdrawn 2015)
API 920 : 1990 PREVENTION OF BRITTLE FRACTURE OF PRESSURE VESSELS
ASTM F 1007 : 1986 : R2014 Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application
AWS A5.22/A5.22M : 2012 SPECIFICATION FOR STAINLESS STEEL FLUX CORED AND METAL CORED WELDING ELECTRODES AND RODS
API 620 : 2013 DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS
AWS A5.29 : 1998 SPECIFICATION FOR LOW ALLOY STEEL ELECTRODES FOR FLUX CORED ARC WELDING
NACE TM 01 03 : 2003 LABORATORY TEST PROCEDURES FOR EVALUATION OF SOHIC RESISTANCE OF PLATE STEELS USED IN WET H[2]S SERVICE
W48-18 Filler metals and allied materials for metal arc welding
ASTM C 868 : 2002 Standard Test Method for Chemical Resistance of Protective Linings
ASTM C 868 : 2002 : R2008 Standard Test Method for Chemical Resistance of Protective Linings
ASTM F 1007 : 1986 : R2002 Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application
ASME B31.1 : 2016 POWER PIPING
ASME PV CODE 2C : 2017 BOILER AND PRESSURE VESSEL CODE - MATERIALS - SPECIFICATIONS FOR WELDING RODS, ELECTRODES, AND FILLER METALS
ASME B31.4 : 2016 PIPELINE TRANSPORTATION SYSTEMS FOR LIQUIDS AND SLURRIES
ASME B31.3:2016 PROCESS PIPING
API SPEC 12K : 2008 SPECIFICATION FOR INDIRECT TYPE OILFIELD HEATERS
13/30294315 DC : 0 PD 5500:2012+A3:2013 - SPECIFICATION FOR UNFIRED FUSION WELDED PRESSURE VESSELS
MIL C 15730 : M COOLER, FLUID, NAVAL SHIPBOARD, LUBRICATING OIL, HYDRAULIC OIL, AND FRESH WATER
BS ISO 21172-1:2015 Gas cylinders. Welded steel pressure drums up to 3 000 litres capacity for the transport of gases. Design and construction Capacities up to 1 000 litres
15/30299570 DC : 0 BS ISO 7195 - NUCLEAR ENERGY - PACKAGINGS FOR THE TRANSPORT OF URANIUM HEXAFLUORIDE (UF[6])
MSS SP 81 : 2017 STAINLESS-STEEL OR STAINLESS-STEEL-LINED, BONNETLESS, KNIFE GATE VALVES WITH FLANGED ENDS
Z245.15-17 Steel valves
AWS C5.7 : 2000 RECOMMENDED PRACTICES FOR ELECTROGAS WELDING
MSS SP 148 : 2014 LOW PRESSURE FLANGED OR LUGGED CARBON STEEL AND IRON OR DUCTILE IRON, CAST OR FABRICATED, BONNETLESS, KNIFE GATE VALVES WITHOUT LINERS
AWWA C520 : 2014 KNIFE GATE VALVES, SIZES 2 IN. (50 MM) THROUGH 96 IN. (2,400 MM)
ASTM A 672/A672M : 2014 : REDLINE Standard Specification for Electric-Fusion-Welded Steel Pipe for High-Pressure Service at Moderate Temperatures
ASTM F 1602 : 2012 Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated
API 650 : 2013 WELDED TANKS FOR OIL STORAGE
NF ISO 7195 : 2005 NUCLEAR ENERGY - PACKAGING OF URANIUM HEXAFLUORIDE (UF6) FOR TRANSPORT
ISO 7195:2005 Nuclear energy Packaging of uranium hexafluoride (UF6) for transport
API 6H : 1998 : R2011 SPECIFICATION ON END CLOSURES, CONNECTORS AND SWIVELS
ASTM D 2485 : 2018 : REDLINE Standard Test Methods for Evaluating Coatings For High Temperature Service
AWWA C512 : 2015 AIR-RELEASE, AIR/VACUUM, AND COMBINATION AIR VALVES FOR WATER AND WASTEWATER SERVICE
13/30264471 DC : 0 BS ISO 21172-1 - GAS CYLINDERS - WELDED STEEL PRESSURE DRUMS UP TO 3000 LITRES CAPACITY FOR THE TRANSPORT OF GASES - DESIGN AND CONSTRUCTION - PART 1: CAPACITIES UP TO 1000 LITRES
API 12F CHINESE : 2008 SPECIFICATION FOR SHOP WELDED TANKS FOR STORAGE OF PRODUCTION LIQUIDS
AWWA C301 : 2014 PRESTRESSED CONCRETE PRESSURE PIPE, STEEL-CYLINDER TYPE
ASTM A 134 : 1996 Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
API 939-B : 2002 REPAIR AND REMEDIATION STRATEGIES FOR EQUIPMENT OPERATING IN WET H[2]S SERVICE
API SPEC 12L : 2008 SPECIFICATION FOR VERTICAL AND HORIZONTAL EMULSION TREATERS
API 620 CHINESE : 2013 DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS
API 12F : 2008 SPECIFICATION FOR SHOP WELDED TANKS FOR STORAGE OF PRODUCTION LIQUIDS
API 620 REDLINE : 2008 DESIGN AND CONSTRUCTION OF LARGE, WELDED, LOW-PRESSURE STORAGE TANKS
NFPA 22 : 2018 WATER TANKS FOR PRIVATE FIRE PROTECTION
ASTM F 1007 : 1986 : R1996 : EDT 1 Standard Specification for Pipe-Line Expansion Joints of the Packed Slip Type for Marine Application
ASTM D 3491 : 1992 Standard Test Methods for Vulcanizable Rubber Tank and Pipe Lining (Withdrawn 1996)
ASTM F 1602 : 2012 : R2017 Standard Specification for Kettles, Steam-Jacketed, 20 to 200 gal (75.7 to 757 L), Floor or Wall Mounted, Direct Steam, Gas and Electric Heated
ASTM A 134 : 1996 : R2005 Standard Specification for Pipe, Steel, Electric-Fusion (Arc)-Welded (Sizes NPS 16 and Over)
API 650 : 2013+ADD 3 : 2018 WELDED TANKS FOR OIL STORAGE
ISO 10439:2002 Petroleum, chemical and gas service industries Centrifugal compressors
EN ISO 10439:2002 Petroleum, chemical and gas service industries - Centrifugal compressors (ISO 10439:2002)
API 650 CHINESE : 2013 WELDED TANKS FOR OIL STORAGE
MIL-DTL-17849 Revision F:2018 Strainers, Sediment, Pipeline, Duplex (with and without Magnet)
ASTM F 1603 : 2017 : REDLINE Standard Specification for Kettles, Steam-Jacketed, 32 oz to 20 gal (1 to 75.7 L), Tilting, Table Mounted, Direct Steam, Gas and Electric Heated
AWS A5.17/A5.17M : 1997 SPECIFICATION FOR CARBON STEEL ELECTRODES AND FLUXES FOR SUBMERGED ARC WELDING
ASTM F 1007 : 1986 : R2007 Standard Specification for Pipeline Expansion Joints of the Packed Slip Type for Marine Application
ASTM A 671 : 2009 Standard Specification for Electric-Fusion-Welded Steel Pipe for Atmospheric and Lower Temperatures
API 6H : 1998 SPECIFICATION ON END CLOSURES, CONNECTORS AND SWIVELS
ANSI/AWWA C300 : 2016 REINFORCED CONCRETE PRESSURE PIPE, STEEL - CYLINDER TYPE
API 6H CHINESE : 1998 SPECIFICATION ON END CLOSURES, CONNECTORS AND SWIVELS
AWS A5.4/A5.4M : 2012 SPECIFICATION FOR STAINLESS STEEL ELECTRODES FOR SHIELDED METAL ARC WELDING
AWS A5.29/A5.29M : 2010 SPECIFICATION FOR LOW-ALLOY STEEL ELECTRODES FOR FLUX CORED ARC WELDING
AWWA C302 : 2016 REINFORCED CONCRETE PRESSURE PIPE, NONCYLINDER TYPE
AWS A5.20/A5.20M : 2005 : R2015 SPECIFICATION FOR CARBON STEEL ELECTRODES FOR FLUX CORED ARC WELDING
ASME B31.12 : 2014 HYDROGEN PIPING AND PIPELINES

ASTM A 435/A435M : 2017 : REDLINE Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates
ASTM A 577/A577M : 2017 : REDLINE Standard Specification for Ultrasonic Angle-Beam Examination of Steel Plates
ASTM A 299/A299M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, Manganese-Silicon
ASTM A 516/A516M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Moderate- and Lower-Temperature Service
ASTM A 578/A578M : 2017 : REDLINE Standard Specification for Straight-Beam Ultrasonic Examination of Rolled Steel Plates for Special Applications
ASTM A 515/A515M : 2017 : REDLINE Standard Specification for Pressure Vessel Plates, Carbon Steel, for Intermediate- and Higher-Temperature Service

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.