Standard Specification for Manganese Bronze Rod, Bar, and Shapes

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

04-01-2017

Publisher

American Society for Testing and Materials

CONTAINED IN VOL. 02.01, 2017 Describes the requirements for manganese bronze rod, bar and shapes produced in Copper Alloy UNS No. C67000, C67500, or C67600.

1.1This specification establishes the requirements for manganese bronze rod, bar and shapes produced in Copper Alloy UNS Nos. C67000, C67500, or C67600.

1.2Units—The values stated in inch-pound units or SI units are to be regarded separately in the standard. Within the text, the SI values are shown in brackets. The values stated in each system of units may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in nonconformance with the standard.

1.3Warning—Mercury has been designated by many regulatory agencies as a hazardous material that can cause serious medical issues. Mercury, or its vapor, has been demonstrated to be hazardous to health and corrosive to materials. Caution should be taken when handling mercury and mercury containing products. See the applicable product Safety Data Sheet (SDS) for additional information. Users should be aware that selling mercury and/or mercury containing products into your state or country may be prohibited by law.

Note 1:Product suitable for hot forging applications is available under Specification B124/B124M.

1.4The following safety hazard caveat pertains only to the Performance Requirements section of this specification.

1.4.1This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	B 05
DevelopmentNote	Supersedes ASTM B 138 and ASTM B 138M. (09/2001)
DocumentType	Standard
Pages	4
ProductNote	Reconfirmed 2017
PublisherName	American Society for Testing and Materials
Status	Current

ASTM E 8/E8M : 2024	Standard Test Methods for Tension Testing of Metallic Materials
ASTM E 8/E8M : 2016 : REV A : EDT 1	Standard Test Methods for Tension Testing of Metallic Materials
ASTM B 154 : 2016 : REDLINE	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
ASTM E 8/E8M : 2021	Standard Test Methods for Tension Testing of Metallic Materials
ASTM B 154 : 2016	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
ASTM E 8/E8M : 2022	Standard Test Methods for Tension Testing of Metallic Materials
ASTM B 124/B124M : 2010	Standard Specification for Copper and Copper Alloy Forging Rod, Bar, and Shapes
ASTM B 249/B249M : 2023	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ASTM B 249/B249M : 2022	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ASTM B 249/B249M : 2020	Standard Specification for General Requirements for Wrought Copper and Copper-Alloy Rod, Bar, Shapes and Forgings
ASTM E 478 : 2008 : R2017	Standard Test Methods for Chemical Analysis of Copper Alloys
ASTM B 154 : 2016 : R2022	Standard Test Method for Mercurous Nitrate Test for Copper Alloys
ASTM E 8/E8M : 2016-09	TEST METHODS FOR TENSION TESTING OF METALLIC MATERIALS