• There are no items in your cart

ASTM C 1401 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Guide for Structural Sealant Glazing
Available format(s)

Hardcopy , PDF

Superseded date

06-17-2023

Language(s)

English

Published date

07-23-2014

Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system.

1.1Structural sealant glazing, hereinafter referred to as SSG, is an application where a sealant not only can function as a barrier against the passage of air and water through a building envelope, but also primarily provides structural support and attachment of glazing or other components to a window, curtain wall, or other framing system.

1.2This guide provides information useful to design professionals, manufacturers, contractors, and others for the design and installation of a SSG system. This information is applicable only to this glazing method when used for a building wall that is not more than 15° from vertical; however, limited information is included concerning a sloped SSG application.

1.3Only a silicone chemically curing sealant specifically formulated, tested, and marketed for structural sealant glazing is acceptable for a SSG system application.

1.4The committee with jurisdiction for this standard is not aware of any comparable standard published by other organizations.

1.5The calculations and values stated in SI units are to be regarded as the standard. Values in parenthesis and inch-pound units are for information only. SI units in this guide are in conformance with IEEE/ASTM SI 10.

1.6This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
C 24
DocumentType
Guide
Pages
56
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1193 : 2016 Standard Guide for Use of Joint Sealants
ASTM C 1564 : 2015 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM C 1394 : 2003 : R2012 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM C 1487 : 2002 : R2012 Standard Guide for Remedying Structural Silicone Glazing
ASTM C 1394 : 2020 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM C 1472 : 2016 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM C 1184 : 2018 : EDT 1 Standard Specification for Structural Silicone Sealants

ASTM E 2099 : 2000 : R2014 : EDT 1 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM D 1566 : 2004 : REV A Standard Terminology Relating to Rubber
ASTM C 1036 : 2001 Standard Specification for Flat Glass
ASTM C 1115 : 2017 : R2022 Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
ASTM D 1566 : 2009 Standard Terminology Relating to Rubber
ASTM E 2203 : 2002 : R2008 Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
ASTM C 1193 : 2011 : REV A Standard Guide for Use of Joint Sealants
ASTM E 1105 : 2015 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference
ASTM D 1566 : 2006 Standard Terminology Relating to Rubber
ASTM C 1487 : 2002 Standard Guide for Remedying Structural Silicone Glazing
ASTM D 1566 : 2008 : REV A Standard Terminology Relating to Rubber
ASTM C 1184 : 2000 : REV A Standard Specification for Structural Silicone Sealants
ASTM D 1566 : 2021 : REV A Standard Terminology Relating to Rubber
ASTM E 1825 : 2006 : R2012 Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems
ASTM C 719 : 2022 Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
ASTM C 1201 : 1991 : R2003 Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
ASTM E 2431 : 2012 : R2020 Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings
ASTM E 2128 : 2001 : REV A Standard Guide for Evaluating Water Leakage of Building Walls
ASTM C 1172 : 2009 : EDT 1 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1248 : 2004 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM C 1564 : 2004 : R2009 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM C 1330 : 2002 : R2013 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants
ASTM C 1048 : 1997 : REV B Standard Specification for Heat-Treated Flat Glass--Kind HS, Kind FT Coated and Uncoated Glass
ASTM E 2203 : 2014 : R2018 Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
ASTM D 4541 : 2009 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM C 1472 : 2005 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM E 1886 : 2004 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM D 1566 : 2005 Standard Terminology Relating to Rubber
ASTM E 2128 : 2017 Standard Guide for Evaluating Water Leakage of Building Walls
ASTM E 1996 : 2012 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1193 : 2016 Standard Guide for Use of Joint Sealants
ASTM C 1487 : 2000 Standard Guide for Remedying Structural Silicone Glazing
ASTM C 1184 : 2018 : EDT 1 Standard Specification for Structural Silicone Sealants
ASTM C 1394 : 2003 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM E 2203 : 2002 Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
ASTM C 1330 : 1996 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants
ASTM C 1521 : 2009 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 1036 : 2021 Standard Specification for Flat Glass
ASTM D 1566 : 2002 : REV A Standard Terminology Relating to Rubber
ASTM C 1253 : 1993 : R1998 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM E 1105 : 2000 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform or Cyclic Static Air Pressure Difference
ASTM E 1996 : 2012 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1472 : 2010 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM E 1300 : 2004 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM E 1886 : 2013 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 1105 : 2000 : R2008 Standard Test Method for Field Determination of Water Penetration of Installed Exterior Windows, Skylights, Doors, and Curtain Walls, by Uniform or Cyclic Static Air Pressure Difference
ASTM C 1036 : 2006 Standard Specification for Flat Glass
ASTM C 1265 : 1994 : R2011 Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
ASTM E 1424 : 1991 : R2008 Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen
ASTM C 1394 : 2003 : R2008 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM C 1253 : 2014 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM C 1294 : 2015 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 1300 : 2000 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1369 : 2007 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 1330 : 2002 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants
ASTM C 1135 : 2000 : R2011 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM E 2128 : 2001 Standard Guide for Evaluating Water Leakage of Building Walls
ASTM C 1472 : 2006 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM D 1566 : 2007 Standard Terminology Relating to Rubber
ASTM E 1300 : 2012 : REV A : EDT 1 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1193 : 2005 : REV A Standard Guide for Use of Joint Sealants
ASTM D 1566 : 2019 Standard Terminology Relating to Rubber
ASTM C 1472 : 2016 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM C 1184 : 2018 Standard Specification for Structural Silicone Sealants
ASTM D 1566 : 2015 Standard Terminology Relating to Rubber
ASTM C 1087 : 2000 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 1825 : 2017 Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems
ASTM D 2203 : 2001 : R2007 Standard Test Method for Staining from Sealants
ASTM C 1294 : 2007 : EDT 1 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 1996 : 2002 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM C 1048 : 2018 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM E 1425 : 2014 Standard Practice for Determining the Acoustical Performance of Windows, Doors, Skylight, and Glazed Wall Systems
ASTM D 1566 : 2008 Standard Terminology Relating to Rubber
ASTM C 1265 : 1994 : R2005 : EDT 1 Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
ASTM C 1201 : 1991 : R1996 Standard Test Method for Structural Performance of Exterior Dimension Stone Cladding Systems by Uniform Static Air Pressure Difference
ASTM C 1172 : 2003 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1115 : 2017 Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
ASTM C 1294 : 2007 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 2431 : 2012 Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings
ASTM C 1248 : 2008 : R2012 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM C 1253 : 2014 : R2019 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM D 4541 : 2009 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 2099 : 2000 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM D 1566 : 2005 : REV A Standard Terminology Relating to Rubber
ASTM E 2128 : 2012 Standard Guide for Evaluating Water Leakage of Building Walls
ASTM C 1330 : 2002 : R2007 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid Applied Sealants
ASTM C 1369 : 2019 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM E 1996 : 2006 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1135 : 2019 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1249 : 2006 Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
ASTM C 1253 : 1993 : R2009 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM C 1265 : 2017 Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
ASTM C 1036 : 2016 Standard Specification for Flat Glass
ASTM C 1248 : 2006 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM E 1424 : 1991 : R2000 Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen
ASTM E 2431 : 2006 Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings
ASTM C 1521 : 2009 : EDT 1 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM E 1425 : 2007 Standard Practice for Determining the Acoustical Performance of Windows, Doors, Skylight, and Glazed Wall Systems
ASTM C 1369 : 2007 : R2014 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM E 1996 : 2005 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1996 : 2004 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM D 1566 : 2006 : REV A Standard Terminology Relating to Rubber
ASTM E 2099 : 2000 : R2007 Standard Practice for the Specification and Evaluation of Pre-Construction Laboratory Mockups of Exterior Wall Systems
ASTM E 1886 : 2005 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM D 1566 : 2003 : REV A Standard Terminology Relating to Rubber
ASTM C 1193 : 2012 Standard Guide for Use of Joint Sealants
ASTM D 4541 : 2002 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM C 1036 : 2011 Standard Specification for Flat Glass
ASTM C 1521 : 2008 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 1564 : 2004 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM E 1300 : 2002 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM E 1300 : 2009 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM D 1566 : 2006 : REV B Standard Terminology Relating to Rubber
ASTM D 2203 : 2001 : R2018 Standard Test Method for Staining from Sealants
ASTM E 1825 : 1996 Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems
ASTM E 1996 : 2008 : EDT 1 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1184 : 2000 : REV A : EDT 1 Standard Specification for Structural Silicone Sealants
ASTM C 1135 : 2000 : R2005 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1193 : 2005 Standard Guide for Use of Joint Sealants
ASTM C 1487 : 2002 : R2007 Standard Guide for Remedying Structural Silicone Glazing
ASTM D 2203 : 1993 Standard Test Method for Staining from Sealants
ASTM E 1300 : 2009 : REV A Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM D 4541 : 2017 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM E 1996 : 2009 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM D 1566 : 2005 : REV B Standard Terminology Relating to Rubber
ASTM E 1300 : 2012 : REV A Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1521 : 2002 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 1294 : 1995 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM C 1564 : 2020 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM E 1996 : 2001 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM C 1394 : 2003 : R2012 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM C 1135 : 2000 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM C 1048 : 2012 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM C 1487 : 2002 : R2012 Standard Guide for Remedying Structural Silicone Glazing
ASTM C 1172 : 2009 Standard Specification for Laminated Architectural Flat Glass
ASTM D 1566 : 2011 Standard Terminology Relating to Rubber
ASTM C 1135 : 2015 Standard Test Method for Determining Tensile Adhesion Properties of Structural Sealants
ASTM E 1996 : 2014 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM D 1566 : 2021 Standard Terminology Relating to Rubber
ASTM D 2203 : 2001 : R2011 Standard Test Method for Staining from Sealants
ASTM E 1996 : 2014 : REV A Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1048 : 2004 Standard Specification for Heat-Treated Flat Glass—Kind HS, Kind FT Coated and Uncoated Glass
ASTM C 1249 : 1993 Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
ASTM C 1115 : 2006 Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
ASTM C 1521 : 2019 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM E 1233 : 2000 Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Cyclic Static Air Pressure Differential
ASTM D 1566 : 2000 : REV B Standard Terminology Relating to Rubber
ASTM C 719 : 2014 : R2019 Standard Test Method for Adhesion and Cohesion of Elastomeric Joint Sealants Under Cyclic Movement (Hockman Cycle)
ASTM E 1886 : 2013 : REV A Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1087 : 2016 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1521 : 2008 : REV A Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM E 1996 : 2005 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1233 : 2006 Standard Test Method for Structural Performance of Exterior Windows, Doors, Skylights, and Curtain Walls by Cyclic Air Pressure Differential
ASTM E 1825 : 2021 Standard Guide for Evaluation of Building Exterior Enclosure Materials, Products, and Systems
ASTM D 1566 : 2014 Standard Terminology Relating to Rubber
ASTM C 1394 : 1998 Standard Guide for In-Situ Structural Silicone Glazing Evaluation
ASTM C 1265 : 1994 : R1999 Standard Test Method for Determining the Tensile Properties of an Insulating Glass Edge Seal for Structural Glazing Applications
ASTM C 1193 : 2000 Standard Guide for Use of Joint Sealants
ASTM E 1996 : 2017 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1392 : 2000 : R2009 Standard Guide for Evaluating Failure of Structural Sealant Glazing
ASTM C 1172 : 2014 Standard Specification for Laminated Architectural Flat Glass
ASTM E 1300 : 2003 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1087 : 2000 : R2011 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 509 : 2006 : R2015 Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing<brk/> Material
ASTM C 1521 : 2002 : REV A Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM D 1566 : 2010 Standard Terminology Relating to Rubber
ASTM C 1392 : 2000 Standard Guide for Evaluating Failure of Structural Sealant Glazing
ASTM C 1564 : 2003 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM C 1521 : 2019 : R2020 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 1249 : 2018 Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
ASTM E 1425 : 1991 : R1999 Standard Practice for Determining the Acoustical Performance of Exterior Windows and Doors
ASTM E 1996 : 2008 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM E 1886 : 2019 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1472 : 2016 : EDT 1 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM C 1294 : 2001 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 1996 : 2005 : REV B Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Impact Protective Systems Impacted by Windborne Debris in Hurricanes
ASTM C 1248 : 2018 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM C 1294 : 2007 : R2011 Standard Test Method for Compatibility of Insulating Glass Edge Sealants with Liquid-Applied Glazing Materials
ASTM E 1996 : 2003 Standard Specification for Performance of Exterior Windows, Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
ASTM D 1566 : 2003 Standard Terminology Relating to Rubber
ASTM C 510 : 2016 Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
ASTM C 1392 : 2000 : R2005 Standard Guide for Evaluating Failure of Structural Sealant Glazing
ASTM C 1036 : 2011 : EDT 1 Standard Specification for Flat Glass
ASTM C 1115 : 2000 Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
ASTM C 1369 : 1997 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM C 509 : 2006 : R2021 Standard Specification for Elastomeric Cellular Preformed Gasket and Sealing<brk/> Material
ASTM D 1566 : 2000 Standard Terminology Relating to Rubber
ASTM E 1300 : 2016 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1369 : 2002 Standard Specification for Secondary Edge Sealants for Structurally Glazed Insulating Glass Units
ASTM E 1300 : 2004 : EDT 1 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM E 2128 : 2001 : REV A : R2009 Standard Guide for Evaluating Water Leakage of Building Walls
ASTM C 1193 : 2011 Standard Guide for Use of Joint Sealants
ASTM C 1564 : 2015 Standard Guide for Use of Silicone Sealants for Protective Glazing Systems
ASTM C 1184 : 2005 Standard Specification for Structural Silicone Sealants
ASTM C 510 : 2016 : R2022 Standard Test Method for Staining and Color Change of Single- or Multicomponent Joint Sealants
ASTM E 1300 : 2012 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM C 1521 : 2013 Standard Practice for Evaluating Adhesion of Installed Weatherproofing Sealant Joints
ASTM C 1048 : 2012 : EDT 1 Standard Specification for Heat-Strengthened and Fully Tempered Flat Glass
ASTM E 2203 : 2014 Standard Specification for Dense Thermoplastic Elastomers Used for Compression Seals, Gaskets, Setting Blocks, Spacers and Accessories
ASTM D 4541 : 1995 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 1566 : 2020 Standard Terminology Relating to Rubber
ASTM D 1566 : 2007 : REV A Standard Terminology Relating to Rubber
ASTM C 1392 : 2020 Standard Guide for Evaluating Failure of Structural Sealant Glazing
ASTM C 1248 : 2008 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM C 1087 : 2000 : R2006 : EDT 1 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM E 1886 : 2002 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM E 1886 : 2004 : REV A Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Impact Protective Systems Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM C 1087 : 2000 : R2006 Standard Test Method for Determining Compatibility of Liquid-Applied Sealants with Accessories Used in Structural Glazing Systems
ASTM C 1472 : 2000 Standard Guide for Calculating Movement and Other Effects When Establishing Sealant Joint Width
ASTM C 1392 : 2000 : R2014 Standard Guide for Evaluating Failure of Structural Sealant Glazing
ASTM C 1193 : 2013 Standard Guide for Use of Joint Sealants
ASTM C 1184 : 2013 Standard Specification for Structural Silicone Sealants
ASTM D 1566 : 2005 : REV C Standard Terminology Relating to Rubber
ASTM E 330 : 1997 : EDT 1 Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference
ASTM C 1184 : 2014 Standard Specification for Structural Silicone Sealants
ASTM E 1825 : 2006 Standard Guide for Evaluation of Exterior Building Wall Materials, Products, and Systems
ASTM D 2203 : 2001 Standard Test Method for Staining from Sealants
ASTM C 1115 : 2006 : R2011 Standard Specification for Dense Elastomeric Silicone Rubber Gaskets and Accessories
ASTM C 1487 : 2019 Standard Guide for Remedying Structural Silicone Glazing
ASTM C 1248 : 1993 : R1998 Standard Test Method for Staining of Porous Substrate by Joint Sealants
ASTM E 2431 : 2006 : R2011 Standard Practice for Determining the Resistance of Single Glazed Annealed Architectural Flat Glass to Thermal Loadings
ASTM C 1036 : 1991 : R1997 Standard Specification for Flat Glass
ASTM E 1424 : 1991 : R2016 Standard Test Method for Determining the Rate of Air Leakage Through Exterior Windows, Curtain Walls, and Doors Under Specified Pressure and Temperature Differences Across the Specimen
ASTM E 1300 : 2007 : EDT 1 Standard Practice for Determining Load Resistance of Glass in Buildings
ASTM E 1886 : 1997 Standard Test Method for Performance of Exterior Windows, Curtain Walls, Doors, and Storm Shutters Impacted by Missile(s) and Exposed to Cyclic Pressure Differentials
ASTM D 1566 : 2010 : EDT 1 Standard Terminology Relating to Rubber
ASTM C 1172 : 2019 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1253 : 1993 : R2005 Standard Test Method for Determining the Outgassing Potential of Sealant Backing
ASTM C 1172 : 1996 : EDT 1 Standard Specification for Laminated Architectural Flat Glass
ASTM C 1330 : 2018 Standard Specification for Cylindrical Sealant Backing for Use with Cold Liquid-Applied Sealants
ASTM C 1249 : 2006 : REV A Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
ASTM C 1193 : 2009 Standard Guide for Use of Joint Sealants
ASTM C 1249 : 2006 : REV A : R2010 Standard Guide for Secondary Seal for Sealed Insulating Glass Units for Structural Sealant Glazing Applications
ASTM D 1566 : 2008 : REV B Standard Terminology Relating to Rubber

View more information
US$117.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.