ASTM C 1482 : 2017
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Specification for Polyimide Flexible Cellular Thermal and Sound Absorbing Insulation
Available format(s)
Hardcopy , PDF
Superseded date
04-08-2024
Language(s)
English
Published date
09-19-2017
1.1This specification covers the composition and physical properties of lightweight, flexible open-cell polyimide foam insulation intended for use as thermal and sound-absorbing insulation for temperatures from –328°F up to +572°F (–200°C and +300°C) in commercial and industrial environments.
1.1.1Annex A1 includes faced polyimide foam as specified by the U.S. Navy for marine applications.
1.1.2This standard is designed as a material specification and not a design document. Physical property requirements vary by application and temperature. No single test is adequate for estimating either the minimum or maximum use temperature of polyimide foam under all possible conditions. Consult the manufacturer for specific recommendations and physical properties for specific applications.
1.1.3The use of an appropriate vapor retarder is required in all applications where condensation could occur and cause a decrease in thermal performance or affect other system properties.
1.2The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.
1.3This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire-hazard or fire-risk assessment of the materials, products, or assemblies under actual fire conditions.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health and environmental practices and determine the applicability of regulatory limitations prior to use.
Note 1:The subject matter of this material specification is not covered by any other ASTM specification. There is no known ISO standard covering the subject of this standard.
1.5This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
| Committee |
C 16
|
| DocumentType |
Standard
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM C 1774 : 2013(R2019) | Standard Guide for Thermal Performance Testing of Cryogenic Insulation Systems |
| ASTM C 1558 : 2019 | Standard Guide for Development of Standard Data Records for Computerization of Thermal Transmission Test Data for Thermal Insulation |
| ASTM C 1774 : 2013 | Standard Guide for Thermal Performance Testing of Cryogenic Insulation Systems |
| ASTM C 1594 : 2011 : R2017 | Standard Specification for Polyimide Rigid Cellular Thermal Insulation |
| ASTM F 683 : 2014 | Standard Practice for Selection and Application of Thermal Insulation for Piping and Machinery |
| ASTM C 165 : 2023 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
| ASTM E 662 : 2021 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM E 1354 : 2010 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 585 : 2022 | Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing |
| ASTM C 168 : 2019 | Standard Terminology Relating to Thermal Insulation |
| ASTM C 1045 : 2019 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1559 : 2015 : R2021 | Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type) |
| ASTM E 1354 : 2002 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 177 : 2019 | Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
| ASTM C 1114 : 2006 : R2013 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1114 : 2006 : R2019 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM E 1354 : 2014 : EDT 1 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 2126 : 1999 | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM C 1045 : 2007 : R2013 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM D 2126 : 2004 | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM C 1559 : 2003 | Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type) |
| ASTM C 1304 : 2008 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM D 3675 : 2022 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 2231 : 2002 : EDT 1 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 96/E96M : 2022 : REV A : EDT 1 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 3675 : 2005 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM C 634 : 2013 : EDT 1 | Standard Terminology Relating to Building and Environmental Acoustics |
| ASTM E 96/E96M : 2022 : REV A | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM C 634 : 2022 | Standard Terminology Relating to Building and Environmental Acoustics |
| ASTM D 3675 : 2009 : REV A | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 1354 : 2004 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 1304 : 2008 : R2013 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM E 1354 : 1999 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 96/E96M : 2021 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM C 302 : 1995 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM C 1559 : 2015 | Standard Test Method for Determining Wicking of Fibrous Glass Blanket Insulation (Aircraft Type) |
| ASTM C 1304 : 2018 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM D 3675 : 2009 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 1354 : 2010 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 795 : 2016 | Standard Practices for Mounting Test Specimens During Sound Absorption Tests |
| ASTM C 1058 : 1997 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM E 662 : 2021 : REV A | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM C 1338 : 2000 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 447 : 2015 | Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations |
| ASTM E 1354 : 2003 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 1058 : 2003 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM C 423 : 2017 | Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method |
| ASTM D 2126 : 2015 | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM D 3675 : 2021 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 96/E96M : 2022 | Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials |
| ASTM D 3675 : 2014 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 1354 : 2002 : REV D : EDT 1 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 2231 : 2014 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 447 : 2015 : R2022 | Standard Practice for Estimating the Maximum Use Temperature of Thermal Insulations |
| ASTM E 176 : 2021 : REV A : EDT 1 | Standard Terminology of Fire Standards |
| ASTM E 84 : 2023 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 634 : 2013 : R2021 | Standard Terminology Relating to Building and Environmental Acoustics |
| ASTM D 3574 : 2011 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM E 1354 : 2008 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 423 : 2022 | Standard Test Method for Sound Absorption and Sound Absorption Coefficients by the Reverberation Room Method |
| ASTM E 176 : 2018 : REV A : EDT 1 | Standard Terminology of Fire Standards |
| ASTM E 1354 : 2002 : REV D | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 543 : 2021 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM E 2231 : 2019 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 662 : 2019 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM C 1114 : 2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM C 1045 : 2001 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 1338 : 2014 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM E 84 : 2021 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 518 : 2002 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM C 1559 : 2004 | Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type) |
| ASTM E 2231 : 2021 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 84 : 2022 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 2231 : 2007 : REV A | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 1354 : 2009 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 2231 : 2002 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1338 : 2019 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM C 1338 : 2008 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM D 3574 : 2008 | Standard Test Methods for Flexible Cellular Materials<span class='unicode'>—</span>Slab, Bonded, and Molded Urethane Foams |
| ASTM C 1304 : 1995 | Standard Test Method for Assessing the Odor Emission of Thermal Insulation Materials |
| ASTM C 302 : 2013 : R2017 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM E 1354 : 2022 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 3574 : 2017 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM C 1338 : 2019 : R2022 | Standard Test Method for Determining Fungi Resistance of Insulation Materials and Facings |
| ASTM E 84 : 2020 | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM E 1354 : 2015 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 84 : 2021 : REV A | Standard Test Method for Surface Burning Characteristics of Building Materials |
| ASTM C 165 : 2007 : R2017 | Standard Test Method for Measuring Compressive Properties of Thermal Insulations |
| ASTM E 1354 : 2016 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 2231 : 2009 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM C 1114 : 2000 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM D 3675 : 2001 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using A Radiant Heat Energy Source |
| ASTM D 3675 : 2008 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 2231 : 2007 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 176 : 2021 | Standard Terminology of Fire Standards |
| ASTM D 3574 : 1995 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM E 96/E96M : 2016 | Standard Test Methods for Water Vapor Transmission of Materials |
| ASTM D 3675 : 2019 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3574 : 1977 : EDT 2 | Standard Methods of Testing Flexible Cellular Materials-Slab, Bonded, And Molded Urethane Foams |
| ASTM D 638 : 2014 | Standard Test Method for Tensile Properties of Plastics |
| ASTM E 2231 : 2018 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 1354 : 2022 : REV C | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 3675 : 2016 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 176 : 2018 : REV A : EDT 2 | Standard Terminology of Fire Standards |
| ASTM E 1354 : 2016 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 518 : 2017 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM D 543 : 2020 | Standard Practices for Evaluating the Resistance of Plastics to Chemical Reagents |
| ASTM E 1354 : 2017 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 1354 : 2002 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 518 : 2021 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
| ASTM D 3675 : 2021 : REV A | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3574 : 2003 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM E 1354 : 2015 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 1114 : 2000 : R2006 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Thin-Heater Apparatus |
| ASTM D 3574 : 2016 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM D 2126 : 2009 | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM C 1045 : 1997 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM C 585 : 2010 : R2016 | Standard Practice for Inner and Outer Diameters of Thermal Insulation for Nominal Sizes of Pipe and Tubing |
| ASTM E 1354 : 2011 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 177 : 2019 : EDT 1 | Standard Test Method for Steady-State Heat Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate Apparatus |
| ASTM E 1354 : 2011 : REV B | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 1354 : 2022 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 795 : 2023 | Standard Practices for Mounting Test Specimens During Sound Absorption Tests |
| ASTM E 1354 : 2011 : REV A | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 3675 : 2017 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3574 : 2001 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM C 168 : 2022 | Standard Terminology Relating to Thermal Insulation |
| ASTM C 302 : 2013 : R2022 | Standard Test Method for Density and Dimensions of Preformed Pipe-Covering-Type Thermal Insulation |
| ASTM D 3675 : 2011 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM D 3675 : 2012 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using a Radiant Heat Energy Source |
| ASTM E 662 : 2021 : REV A : EDT 1 | Standard Test Method for Specific Optical Density of Smoke Generated by Solid Materials |
| ASTM C 1058 : 2003 : R2008 | Standard Practice for Selecting Temperatures for Evaluating and Reporting Thermal Properties of Thermal Insulation |
| ASTM D 3675 : 1998 | Standard Test Method for Surface Flammability of Flexible Cellular Materials Using A Radiant Heat Energy Source |
| ASTM C 1559 : 2004 : R2009 | Standard Test Method for Determining Wicking of Glass Fiber Blanket Insulation (Aircraft Type) |
| ASTM E 2231 : 2015 | Standard Practice for Specimen Preparation and Mounting of Pipe and Duct Insulation Materials to Assess Surface Burning Characteristics |
| ASTM E 176 : 2021 : REV A | Standard Terminology of Fire Standards |
| ASTM E 1354 : 2022 : REV B | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM C 1045 : 2007 | Standard Practice for Calculating Thermal Transmission Properties Under Steady-State Conditions |
| ASTM E 1354 : 2004 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 1354 : 2013 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM E 1354 : 2014 | Standard Test Method for Heat and Visible Smoke Release Rates for Materials and Products Using an Oxygen Consumption Calorimeter |
| ASTM D 3574 : 2005 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM D 3574 : 2001 : EDT 1 | Standard Test Methods for Flexible Cellular Materials—Slab, Bonded, and Molded Urethane Foams |
| ASTM D 638 : 2022 | Standard Test Method for Tensile Properties of Plastics |
| ASTM C 518 : 1998 | Standard Test Method for Steady-State Thermal Transmission Properties by Means of the Heat Flow Meter Apparatus |
US$83.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.