• There are no items in your cart

ASTM C 1848 : 2017 : REV A

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Practice for Installation of High-Pressure Spray Polyurethane Foam Insulation for the Building Enclosure
Superseded date

04-11-2023

Published date

11-29-2017

1.1This practice covers the installation of high-pressure spray polyurethane foam (SPF) as an insulation for building enclosure assemblies including: walls, ceilings, attics, floors, and crawl spaces. This practice does not apply to SPF used strictly as a component for an air barrier system or for SPF used in roofing applications.

1.2Building design criteria and selection of SPF are beyond the scope of this practice.

1.3The use of SPF insulation covered by this practice is typically regulated by building codes or other agencies that address fire performance. Where required the fire performance of the material shall be addressed through standard fire test methods established by the appropriate governing documents.

1.4The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.6This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 16
DocumentType
Standard Practice
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 168 : 2019 Standard Terminology Relating to Thermal Insulation
ASTM D 6226 : 2021 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
ASTM D 4541 : 2009 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 7425 : 2008 Standard Specification for Spray Polyurethane Foam Used for Roofing Applications
ASTM D 4541 : 2009 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 5469 : 2000 : R2005 Standard Guide for Application of New Spray Applied Polyurethane Foam and Coated Roofing Systems
ASTM D 4541 : 2002 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 6226 : 2005 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
ASTM D 6226 : 1998 : EDT 1 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
ASTM D 4449 : 1990 : R1999 Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance
ASTM D 4541 : 2017 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 4541 : 2022 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 4263 : 1983 : R2005 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
ASTM D 4263 : 1983 : R1999 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
ASTM D 5469 : 2000 Standard Guide for Application of New Spray Applied Polyurethane Foam and Coated Roofing Systems
ASTM D 4449 : 2015 Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance
ASTM D 4449 : 2015 : R2021 Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance
ASTM D 6226 : 2015 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
ASTM D 6226 : 2010 Standard Test Method for Open Cell Content of Rigid Cellular Plastics
ASTM D 4263 : 1983 : R2012 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method
ASTM C 168 : 2022 Standard Terminology Relating to Thermal Insulation
ASTM D 4449 : 2008 Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance
ASTM D 4541 : 1995 : EDT 1 Standard Test Method for Pull-Off Strength of Coatings Using Portable Adhesion Testers
ASTM D 4449 : 1990 : R2004 Standard Test Method for Visual Evaluation of Gloss Differences Between Surfaces of Similar Appearance
ASTM D 4263 : 1983 : R2018 Standard Test Method for Indicating Moisture in Concrete by the Plastic Sheet Method

View more information
Sorry this product is not available in your region.

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.