• There are no items in your cart

ASTM C 928 : 2005

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Packaged, Dry, Rapid-Hardening Cementitious Materials for Concrete Repairs
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

05-01-2005

CONTAINED IN VOL. 04.02, 2005 Outlines dry, packaged cementitious mortar or concrete materials for quick repairs to hardened hydraulic-cement concrete structures and pavements.

1.1 This specification covers packaged, dry, cementitious mortar or concrete materials for rapid repairs to hardened hydraulic-cement concrete pavements and structures. Materials that contain organic compounds, such as bitumens, epoxy resins, and polyesters, as the principal binder are not included.

1.1.1 Packaged, dry, concrete material contains aggregate of which at least 5 % by mass of the total mixture is retained on a 9.5-mm (3/8-in.) sieve.

1.1.2 Packaged, dry, mortar material contains aggregate of which less than 5 % by mass of the total mixture is retained on a 9.5-mm (3/8-in.) sieve.

1.2 Aqueous solutions, aqueous emulsions or dispersions may be included as components of the packaged materials. The manufacturer may specify that these liquids are to replace some or all of the mixing water.

1.3 Aggregates must be included as a component of the packaged materials. The manufacturer may recommend job site addition of specific amounts and types of additional aggregates to his product for some uses. However, such reformulated products are not within the scope of this specification.

1.4 The values stated in SI units are to be regarded as standard. The inch-pound units given in parentheses are for information only. Values in SI units shall be obtained by measurement in SI units or by appropriate conversion of measurements made in other units, using the Rules for Conversion and Rounding given in IEEE/ASTM SI-10.

1.5 The following safety hazards caveat pertains to the test methods portion of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Committee
C 09
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ACI 350.5 : 2012 SPECIFICATIONS FOR ENVIRONMENTAL CONCRETE STRUCTURES

ASTM C 403/C403M : 2016 : REDLINE Standard Test Method for Time of Setting of Concrete Mixtures by Penetration Resistance
ASTM C 1012 : 2004 Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
ASTM C 702 : 1998 Standard Practice for Reducing Samples of Aggregate to Testing Size
ASTM C 672/C672M : 2012 Standard Test Method for Scaling Resistance of Concrete Surfaces Exposed to Deicing Chemicals (Withdrawn 2021)
IEEE/ASTM SI_10-2010 American National Standard for Metric Practice
ASTM C 882 : 2005 Standard Test Method for Bond Strength of Epoxy-Resin Systems Used With Concrete By Slant Shear
ASTM C 192/C192M : 2016-04 PRACTICE FOR MAKING AND CURING CONCRETE TEST SPECIMENS IN THE LABORATORY

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.