• There are no items in your cart

ASTM C 1628 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Joints for Concrete Gravity Flow Sewer Pipe, Using Rubber Gaskets
Available format(s)

Hardcopy , PDF

Superseded date

01-09-2024

Language(s)

English

Published date

08-01-2019

This specification covers flexible leak resistant joints for concrete gravity flow sewer pipe using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design.

1.1This specification covers flexible leak resistant joints for concrete gravity flow sewer pipe using rubber gaskets for sealing the joints, where measurable or defined infiltration or exfiltration is a factor of the design. The specification covers the design of joints and the requirements for rubber gaskets to be used therewith, for pipe conforming in all other respects to Specifications C14, C76, C655, C985, and C1417, provided that, if there is conflict in permissible variations in dimension, the requirements of this specification shall govern for joints.

Note 1:Infiltration or exfiltration quantities for an installed pipeline are dependent upon many factors other than the joints, and allowable quantities must be covered by other specifications and suitable testing of the installed pipeline and system. This specification covers the design, material, and performance of the rubber gasket joint only. Joints covered by this specification are for hydrostatic pressures up to 13 psi without leakage, when plant tested in accordance with Section 10.

1.2The values stated in inch-pound units are to be regarded as standard. No other units of measurement are included in this standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
C 13
DocumentType
Standard
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM C 1885 : 2023 Standard Specification for Circular Precast Concrete Culvert, Storm Drain, and Sewer Pipe for Pipe Jacking
ASTM C 655 : 2019 : REV A Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
ASTM C 655M : 2019 : REV A Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe (Metric)
ASTM C 76M : 2022 : REV A Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)
ASTM C 1846/C1846M : 2019 Standard Specification for Performance Based Manufacture of Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe

ASTM C 1417 : 2014 : EDT 1 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 655 : 2019 Standard Specification for Reinforced Concrete D-Load Culvert, Storm Drain, and Sewer Pipe
ASTM C 1619 : 2020 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 1619 : 2019 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 985 : 2019 Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe
ASTM C 822 : 2021 Standard Terminology Relating to Concrete Pipe and Related Products
ASTM C 1417 : 2008 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 1417 : 2019 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 1417 : 2004 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 76 : 2022 : REV A Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
ASTM C 1417 : 2002 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 985 : 2022 Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe
ASTM C 76 : 2020 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
ASTM C 1417 : 2014 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 76 : 2022 Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe
ASTM C 1417 : 2015 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 1417 : 2000 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 822 : 2020 Standard Terminology Relating to Concrete Pipe and Related Products
ASTM C 1619 : 2023 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 1619 : 2011 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 1619 : 2005 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 1417 : 2013 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 1619 : 2011 : R2017 Standard Specification for Elastomeric Seals for Joining Concrete Structures
ASTM C 1417 : 2012 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 1417 : 2011 Standard Specification for Manufacture of Reinforced Concrete Sewer, Storm Drain, and Culvert Pipe for Direct Design
ASTM C 497 : 1998 Standard Test Methods for Concrete Pipe, Manhole Sections, or Tile
ASTM C 985 : 2000 Standard Specification for Nonreinforced Concrete Specified Strength Culvert, Storm Drain, and Sewer Pipe

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.