ASTM D 1037 : 2012 : REDLINE
Current
The latest, up-to-date edition.
English
05-01-2012
CONTAINED IN VOL. 04.10, 2015 Defines the determination of the properties of wood-base fiber and particle panel materials that are produced as mat-formed panels such as particleboard, medium-density fiberboard, hardboard, and oriented strand board.
1.1 Part A
| Section | |
|---|---|
| Significance and Use | 3 |
| Apparatus | 4 |
| Test Specimens | 5 |
| Moisture Content and Conditioning Requirements | 6 |
| Accelerated Aging | 7 |
| Size, Physical Properties and Appearance of Panels | 8 |
| Static Bending | 9 |
| Tension Parallel to Surface | 10 |
| Tension Perpendicular to Surface | 11 |
| Compression Parallel to Surface | 12 |
| Fastener Holding Tests: | |
| Lateral Nail Resistance | 13 |
| Nail Withdrawal | 14 |
| Nail-Head Pull-Through | 15 |
| Direct Screw Withdrawal | 16 |
| Hardness | 17 |
| Hardness Modulus | 18 |
| Shear in the Plane of the Panel | 19 |
| Glue-Line Shear (Block Type) | 20 |
| Falling Ball Impact | 21 |
| Abrasion Resistance by the U.S. Navy Wear Tester | 22 |
| Moisture Tests: | |
| Water Absorption and Thickness Swelling | 23 |
| Linear Expansion with Change in Moisture Content | 24 |
| Cupping and Twisting | 25 |
| Interlaminar Shear | 26 |
| Edgewise Shear | 27 |
| Compression-Shear | 28 |
1.2 Part B
| Section | |
|---|---|
| Thickness | 32 |
| Modulus of Rupture | 33 |
| Tension Strength Parallel to Surface | 34 |
| Tension Strength Perpendicular to Surface | 35 |
| Water Absorption and Thickness Swelling | 36 |
| Moisture Content and Specific Gravity | 37 |
1.3 There are accepted basic test procedures for various fundamental properties of materials that may be used without modification for evaluating certain properties of wood-based fiber and particle panel materials. These test methods are included elsewhere in the Annual Book of ASTM Standards. The pertinent ones are listed in Table 1. A few of the test methods referenced are for construction where the wood-base materials often are used.
1.4 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents are approximate in many cases. 1 in. = 25.4 mm, 1 lbf = 4.45 N.
1.5 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
TABLE 1 Basic Test Procedures for Evaluating Properties of Wood Base-Fiber and Particle Panel Materials
| ASTM Designation | Test Methods for |
|---|---|
| C177 | Steady-State Heat-Flux Measurements and Thermal Transmission Properties by Means of the Guarded-Hot-Plate ApparatusA |
| C209 | Cellulosic Fiber Insulating BoardA |
| C236 | Steady-State Thermal Performance of Building Assemblies by Means of the Guarded Hot BoxA |
| C384 | Impedance and Absorption of Acoustical Materials by the Imped- ance Tube MethodA |
| C423 | Sound Absorption and Sound Absorption Coefficients by the Re- verberation Room MethodA |
| D149 | Dielectric Breakdown Voltage and Dielectric Strength of Solid Elec- trical Insulating Materials at Commercial Power FrequenciesB |
| D150 | A-C Loss Characteristics and Permittivity (Dielectric Constant) of Solid Electrical Insulating MaterialsB |
| D257 | D-C Resistance or Conductance of Insulating MaterialsB |
| D495 | High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical InsulationB |
| D1666 | Conducting Machining Tests of Wood and Wood-Base MaterialsC |
| D1761 | Mechanical Fasteners in WoodC |
| E72 | Conducting Strength Tests of Panels for Building ConstructionD |
| E84 | Surface Burning Characteristics of Building MaterialsD |
| E90 | Laboratory Measurement of Airborne Sound Transmission Loss of Building PartitionsA |
| E96 | Water Vapor Transmission of MaterialsA |
| E97 | Directional Reflectance Factor, 45-deg 0-deg, of Opaque Specimens by Broad-Band Filter ReflectometryE |
| E119 | Fire Tests of Building Construction and MaterialsD |
| E136 | Behavior of Materials in a Vertical Tube Furnace at 750°CD |
| E152 | Fire Tests of Door AssembliesD |
| E162 | Surface Flammability of Materials Using a Radiant Heat Energy SourceD |
| E661 | Performance of Wood and Wood-Based Floor and Roof Sheathing Under Concentrated Static and Impact LoadsD |
| E662 | Specific Optical Density of Smoke Generated by Solid MaterialsD |
| E906 | Heat and Visible Smoke Release Rates for Materials and Prod- uctsD |
A Annual Book of ASTM Standards, Vol 04.06.
B Annual Book of ASTM Standards, Vol 10.01.
C Annual Book of ASTM Standards, Vol 04.10.
D Annual Book of ASTM Standards, Vol 04.07.
E Annual Book of ASTM Standards, Vol 14.02.
| Committee |
D 07
|
| DocumentType |
Redline
|
| Pages |
39
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Current
|
| ASTM C 725 : 1990 : R2014 | Standard Specification for Semidense Mineral Fiber Siding (Withdrawn 2019) |
| CSA O325.1 : 0 | TEST METHODS FOR CONSTRUCTION SHEATHING |
| CSA O325 : 2016 | CONSTRUCTION SHEATHING |
| ASTM C 1705/C1705M : 2009 : R2016 | Standard Specification for Structural Cementitious Panels |
| LLL-B-810 Revision B:1973 | BUILDING BOARD, (HARD BOARD) HARD PRESSED VEGETABLE FIBER |
| ASTM C 209 : 2015 : REDLINE | Standard Test Methods for Cellulosic Fiber Insulating Board |
| ASTM C 1278/C1278M : 2017 : REDLINE | Standard Specification for Fiber-Reinforced Gypsum Panel |
| ASTM D 5651 : 2013 : REDLINE | Standard Test Method for Surface Bond Strength of Wood-Base Fiber and Particle Panel Materials |
| ASTM C 1288 : 2017 : REDLINE | Standard Specification for Fiber-Cement Interior Substrate Sheets |
| ASTM D 7519 : 2011 | Standard Test Method for Internal Bond Strength and Thickness Swell of Cellulosic-Based Fiber and Particle Panels After Repeated Wetting (Withdrawn 2020) |
| ASTM C 725 : 1990 : R2003 | Standard Specification for Semidense Mineral Fiber Siding |
| ASTM C 1325 : 2017-02 | SPECIFICATION FOR NON-ASBESTOS FIBER-MAT REINFORCED CEMENTITIOUS BACKER UNITS |
| ASTM C 725 : 1990 : R1998 | Standard Specification for Semidense Mineral Fiber Siding |
| ASTM D 2394 : 2017 : REDLINE | Standard Test Methods for Simulated Service Testing of Wood and Wood-Based Finish Flooring |
| ASTM C 656 : 2017 : REDLINE | Standard Specification for Structural Insulating Board, Calcium Silicate |
| ASTM C 1705/C1705M : 2009 | Standard Specification for Structural Cementitious Panels |
| ASTM C 208 : 2012 | Standard Specification for Cellulosic Fiber Insulating Board |
| CSA B111 : 0 | WIRE NAILS, SPIKES AND STAPLES |
| SAE J 1774 : 2010 | DESIGN GUIDELINES FOR FIBERBOARD MATERIALS |
| ASTM D 7031 : 2011 : REDLINE | GUIDE FOR EVALUATING MECHANICAL AND PHYSICAL PROPERTIES OF WOOD-PLASTIC COMPOSITE PRODUCTS |
| ASTM E 1803 : 2014 : REDLINE | Standard Test Methods for Determining Strength Capacities of Structural Insulated Panels |
| CSA O437 SERIES : 1993 | STANDARDS ON OSB AND WAFERBOARD |
| ISO 16894:2009 | Wood-based panels Oriented strand board (OSB) Definitions, classification and specifications |
| ISO 8336:2017 | Fibre-cement flat sheets — Product specification and test methods |
| ASTM D 2164 : 1983 : R1994 : EDT 1 | Standard Methods of Testing Structural Insulating Roof Deck |
| ASTM D 2164 : 1983 : R2000 | Standard Methods of Testing Structural Insulating Roof Deck (Withdrawn 2005) |
| ASTM D 2126 : 2015 : REDLINE | Standard Test Method for Response of Rigid Cellular Plastics to Thermal and Humid Aging |
| ASTM D 6815 : 2009 : R2015 | Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products |
| CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
| S806-12 (R2017) | Design and construction of building structures with fibre-reinforced polymers |
| SAE AMS 3940 : 2014 | FIBERBOARD, HARD-PRESSED, STRUCTURAL |
| ASTM D 545 : 2014 : REDLINE | Standard Test Methods for Preformed Expansion Joint Fillers for Concrete Construction (Nonextruding and Resilient Types) |
| LLL B 800 : B NOTICE 1 | BUILDING BOARD (WOOD PARTICLEBOARD) HARD PRESSED VEGETABLE FIBER |
| ASTM C 725 : 1990 : R2008 | Standard Specification for Semidense Mineral Fiber Siding |
| ASTM D 2828 : 1996 : R2003 | Standard Specification for Nonbituminous Inserts for Contraction Joints in Portland Cement Concrete Airfield Pavements, Sawable Type (Withdrawn 2004) |
| ASTM C 208 : 2012 : R2017 : EDT 1 | Standard Specification for Cellulosic Fiber Insulating Board |
| CSA O132.2 SERIES : 0 | WOOD FLUSH DOORS |
| TAPPI T 1003 : CM 83 | FLEXURAL RESISTANCE AND DEFLECTING OF INSULATING BOARD |
| ASTM D 6815 : 2009 | Standard Specification for Evaluation of Duration of Load and Creep Effects of Wood and Wood-Based Products |
| ASTM D 7857 : 2016 | Standard Test Method for Evaluating the Flexural Properties and Internal Bond Strength of Fire-Retarded Mat-Formed Wood Structural Composite Panels Exposed to Elevated Temperatures |
| ASTM D 7032 : 2017 : REDLINE | Standard Specification for Establishing Performance Ratings for Wood-Plastic Composite and Plastic Lumber Deck Boards, Stair Treads, Guards, and Handrails |
| CGSB-11.5 : M87 | HARDBOARD, PRECOATED, FACTORY FINISHED, FOR EXTERIOR CLADDING |
| MIL-I-24330 Base Document:1968 | INSULATION SHEET, ELECTRICAL, LIGNO CELLULOSIC, HIGH DENSITY, HARDBOARD |
| 07/30169285 DC : 0 | BS ISO 8336 - FIBRE-CEMENT FLAT SHEETS - PRODUCT SPECIFICATION AND TEST METHODS |
| CSA Z62.3 : 2011 | CHAIN SAW KICKBACK |
| CGSB-11.3 : M87 | HARDBOARD |
| TAPPI T 1004 : CM 83 | EDGE NAIL STRENGTH OF INSULATING BOARD |
| ASTM C 725 : 1990 : R2003 : EDT 1 | Standard Specification for Semidense Mineral Fiber Siding |
| ASTM D 7033 : 2014 : REDLINE | Standard Practice for Establishing Design Capacities for Oriented Strand Board (OSB) Wood-Based Structural-Use Panels |
| ASTM D 2828 : 1996 | Standard Specification for Nonbituminous Inserts for Contraction Joints in Portland Cement Concrete Airfield Pavements, Sawable Type |
| ASTM D 143 : 2014 : REDLINE | Standard Test Methods for Small Clear Specimens of Timber |
| ASTM D 4442 : 2016 : REDLINE | Standard Test Methods for Direct Moisture Content Measurement of Wood and Wood-Based Materials |
| ASTM D 2395 : 2017 : REDLINE | Standard Test Methods for Density and Specific Gravity (Relative Density) of Wood and Wood-Based Materials |
| ASTM D 905 : 2008 | Standard Test Method for Strength Properties of Adhesive Bonds in Shear by Compression Loading |
| ASTM D 2915 : 2017 : REDLINE | Standard Practice for Sampling and Data-Analysis for Structural Wood and Wood-Based Products |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.