Standard Test Method for Linear Dimensional Changes of Nonrigid Thermoplastic Sheeting or Film at Elevated Temperature

Available format(s)

Hardcopy , PDF

Language(s)

English

Published date

04-01-2020

Publisher

American Society for Testing and Materials

1.1This test method covers the measurement of changes in linear dimensions of nonrigid thermoplastic sheeting or film that result from exposure of the material to specified conditions of elevated temperature and time.

1.2The values stated in SI units are to be regarded as the standard.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

Note 1:This test method and ISO 11501 address the same matter, but differ in technical content (and results cannot be directly compared between the two methods).

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee	D 20
DocumentType	Test Method
Pages	2
PublisherName	American Society for Testing and Materials
Status	Current
Supersedes	ASTM D 1204 : 2014

ASTM D 7613 : 2017 : R2019	Standard Specification for Flexible Polypropylene Reinforced (fPP-R) and Nonreinforced (fPP) Geomembranes
ASTM D 3595 : 2014 : R2019 : EDT 1	Standard Specification for Polychlorotrifluoroethylene (PCTFE) Extruded Plastic Sheet and Film
ASTM D 6434 : 2012 : R2018	Standard Guide for the Selection of Test Methods for Flexible Polypropylene Geomembranes
ASTM C 921 : 2010 : R2015	Standard Practice for Determining the Properties of Jacketing Materials for Thermal Insulation (Withdrawn 2021)
ASTM D 8065/D8065M : 2016	Standard Classification System and Basis for Specification for Specifying Plastic Films
ASTM D 7176 : 2006 : R2018	Standard Specification for Non-Reinforced Polyvinyl Chloride (PVC) Geomembranes Used in Buried Applications
ASTM C 1775 : 2014	Standard Specification for Laminate Protective Jacket and Tape for Use over Thermal Insulation for Outdoor Applications
ASTM D 7832/D7832M : 2014	Standard Guide for Performance Attributes of Waterproofing Membranes Applied to Below-Grade Walls / Vertical Surfaces (Enclosing Interior Spaces)
ASTM D 7106/D7106M : 2005 : R2015 : EDT 1	Standard Guide for Selection of Test Methods for Ethylene Propylene Diene Terpolymer (EPDM) Geomembranes
ASTM D 7194 : 2019	Standard Specification for Aerospace Parts Machined from Polychlorotrifluoroethylene (PCTFE)
ASTM D 7465/D7465M : 2015 : R2019	Standard Specification for Ethylene Propylene Diene Terpolymer (EPDM) Sheet Used In Geomembrane Applications
ASTM F 942 : 2018	Standard Guide for Selection of Test Methods for Interlayer Materials for Aerospace Transparent Enclosures
ASTM D 3664 : 2016	Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment (Withdrawn 2022)
ASTM D 4637/D4637M : 2015	Standard Specification for EPDM Sheet Used In Single-Ply Roof Membrane
ASTM C 1136 : 2017 : REV A	Standard Specification for Flexible, Low Permeance Vapor Retarders for Thermal Insulation
ASTM C 1423 : 2016	Standard Guide for Selecting Jacketing Materials for Thermal Insulation
ASTM D 4801 : 2008 : R2016	Standard Specification for Polyethylene Sheeting in Thickness of 0.25 mm (0.010 in.) and Greater
ASTM D 4434/D4434M : 2015	Standard Specification for Poly(Vinyl Chloride) Sheet Roofing
ASTM D 4068 : 2017	Standard Specification for Chlorinated Polyethylene (CPE) Sheeting for Concealed Water-Containment Membrane
ASTM D 6455 : 2011 : R2018	Standard Guide for the Selection of Test Methods for Prefabricated Bituminous Geomembranes (PBGMs)
ASTM D 4551 : 2017	Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Flexible Concealed Water-Containment Membrane
ASTM D 5819 : 2018	Standard Guide for Selecting Test Methods for Experimental Evaluation of Geosynthetic Durability
ASTM D 6754/D6754M : 2015	Standard Specification for Ketone Ethylene Ester Based Sheet Roofing
ASTM D 1693 : 2015	Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics
ASTM D 1593 : 2019	Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
ASTM D 3105 : 2017	Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials
ASTM D 2643/D2643M : 2008 : R2019	Standard Specification for Prefabricated Bituminous Geomembrane Used as Canal and Ditch Liner (Exposed Type)
ASTM D 5147/D5147M : 2018	Standard Test Methods for Sampling and Testing Modified Bituminous Sheet Material
ASTM D 4811/D4811M : 2016	Standard Specification for Nonvulcanized (Uncured) Rubber Sheet Used as Roof Flashing
ASTM D 1970/D1970M : 2019	Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roofing Underlayment for Ice Dam Protection
ASTM D 6878/D6878M : 2019	Standard Specification for Thermoplastic Polyolefin Based Sheet Roofing

ASTM D 883 : 2023	Standard Terminology Relating to Plastics
ASTM D 2732 : 2014 : R2020	Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 883 : 2024	Standard Terminology Relating to Plastics
ASTM D 883 : 2022	Standard Terminology Relating to Plastics
ASTM D 883 : 2020 : REV B	Standard Terminology Relating to Plastics
ASTM D 4000 : 2023	Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2013	Standard Practice for Conditioning Plastics for Testing
ASTM D 2732 : 2014	Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 4000 : 2020	Standard Classification System for Specifying Plastic Materials
ASTM D 618 : 2021	Standard Practice for Conditioning Plastics for Testing