• There are no items in your cart

ASTM D 1555M : 2016 : REDLINE

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane [Metric]
Available format(s)

PDF

Superseded date

10-10-2022

Language(s)

English

Published date

04-18-2017

CONTAINED IN VOL. 06.04, 2017 Defines the weight and volume of benzene, toluene, mixed xylenes, styrene, ortho-xylene, meta-xylene, para-xylene, cumene, ethylbenzene, 148.9 to 176.7 degrees C and 176.7 to 204.4 degrees C aromatic hydrocarbons, and cyclohexane.

1.1This standard is for use in calculating the weight and volume of benzene, toluene, mixed xylenes, styrene, ortho-xylene, meta-xylene, para-xylene, cumene, ethylbenzene, 148.9 to 176.7°C and 176.7 to 204.4°C aromatic hydrocarbons, and cyclohexane. A method is given for calculating the volume at 15°C and 20°C from an observed volume at t°C. Table 1 lists the density in Vacuo at 60°F for chemicals used to develop the relationship. Densities (or weights) “in vacuo” represent the true density (or weight) if measured in a vacuum without the buoyancy effect of air acting on the liquid. It is representative of the actual amount of product present. Densities (or weights) “in air” represent what would actually be measured on a scale. The difference is on the order of 0.13 %. Modern densitometers measure density in vacuo and the ASTM recommends the use of in vacuo densities (or weights).

(A)Obtained from Method D1555 – 04a by multiplying the chemical's 60°F density by the volume correction factor for 59°F.
(B)Specific Gravity at 15°C is not presented in this table as it is unnecessary to this standard. If needed, divide 15°C density in g/cc by 0.999102 g/cc. See Appendix X1.
(C)g/cc can be converted to kg/1000L or kg/m3 by multiplying by 1000.
(D)Produced using the equation: Density g/mLin air = (1.000149926 × Density g/mLin vacuo − 0.001199407795) and rounding to 5 decimal places. See Appendix X2.
(E)Obtained from Method D1555 - 04a by multiplying the chemical's 60°F density by the volume correction factor for 68°F.
(F)Specific Gravity at 20°C is not presented in this table as it is unnecessary to this standard. If needed, divide 20°C density in g/cc by 0.998206 g/cc. See Appendix X1.

1.2The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.2.1A complete inch-pound unit companion standard has been developed in Test Method D1555.

1.3This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.4This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 16
DocumentType
Redline
Pages
11
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy

ASTM D 5808 : 2009 : REV A Standard Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry
ASTM D 1555 : 2016 : REDLINE Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane
ASTM D 7504 : 2018 : REDLINE Standard Test Method for Trace Impurities in Monocyclic Aromatic Hydrocarbons by Gas Chromatography and Effective Carbon Number
ASTM D 5808 : 2009 : REV A : R2014 Standard Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry
ASTM D 7457 : 2012 Standard Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry (Withdrawn 2019)
ASTM D 5194 : 2018 : REDLINE Standard Test Method for Trace Chloride in Liquid Aromatic Hydrocarbons
ASTM D 5808 : 2009 Standard Test Method for Determining Chloride in Aromatic Hydrocarbons and Related Chemicals by Microcoulometry

ASTM D 1217 : 2015 : REDLINE Standard Test Method for Density and Relative Density (Specific Gravity) of Liquids by Bingham Pycnometer
ASTM D 1555 : 2016 : REDLINE Standard Test Method for Calculation of Volume and Weight of Industrial Aromatic Hydrocarbons and Cyclohexane

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.