ASTM D 1922 : 2015
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
06-01-2023
English
06-30-2015
This test method2 covers the determination of the average force to propagate tearing through a specified length of plastic film or nonrigid sheeting after the tear has been started, using an Elmendorf-type tearing tester.
1.1This test method2 covers the determination of the average force to propagate tearing through a specified length of plastic film or nonrigid sheeting after the tear has been started, using an Elmendorf-type tearing tester. Two specimens are cited, a rectangular type, and one with a constant radius testing length. The latter shall be the preferred or referee specimen.
1.2Because of (1) difficulties in selecting uniformly identical specimens, (2) the varying degree of orientation in some plastic films, and (3) the difficulty found in testing highly extensible or highly oriented materials, or both, the reproducibility of the test results may be variable and, in some cases, not good or misleading. Provisions are made in the test method to address oblique directional tearing which may be found with some materials.
1.3The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in 13.1.
Note 1:Film has been arbitrarily defined as sheeting having nominal thickness not greater than 0.25 mm (0.010 in.).
Note 2:This standard is equivalent to ISO 6383-2.
| Committee |
D 20
|
| DocumentType |
Test Method
|
| Pages |
7
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| ASTM D 8195 : 2018 | Standard Classification System and Basis for Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 228/D228M : 2019 : REV A | Standard Test Methods for Sampling, Testing, and Analysis of Asphalt Roll Roofing, Cap Sheets, and Shingles Used in Roofing and Waterproofing |
| ASTM D 1593 : 2019 | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 1593 : 2013 | Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting |
| ASTM D 2673 : 2014 | Standard Specification for Oriented Polypropylene Film |
| ASTM D 4649 : 2003 : R2016 | Standard Guide for Selection and Use of Stretch Wrap Films |
| ASTM F 2097 : 2016 | Standard Guide for Design and Evaluation of Primary Flexible Packaging for Medical Products |
| ASTM D 4635 : 2016 | Standard Specification for Plastic Films Made from Low-Density Polyethylene and Linear Low-Density Polyethylene for General Use and Packaging Applications |
| ASTM D 2103 : 2015 | Standard Specification for Polyethylene Film and Sheeting |
| ASTM D 5047 : 2017 | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| ASTM D 4869/D4869M : 2016 : REV A | Standard Specification for Asphalt-Saturated Organic Felt Underlayment Used in Steep Slope Roofing |
| ASTM D 3462/D3462M : 2019 | Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules |
| ASTM F 2902 : 2016 : EDT 1 | Standard Guide for Assessment of Absorbable Polymeric Implants |
| ASTM A 674 : 2018 | Standard Practice for Polyethylene Encasement for Ductile Iron Pipe for Water or Other Liquids |
| ASTM D 3105 : 2017 | Standard Index of Methods for Testing Elastomeric and Plastomeric Roofing and Waterproofing Materials |
| ASTM D 3420 : 2014 | Standard Test Method for Pendulum Impact Resistance of Plastic Film |
| ASTM D 1004 : 2008 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 6988 : 2008 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 5947 : 1996 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2013 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1004 : 1994 : REV A | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting |
| ASTM D 1004 : 2009 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 4000 : 2003 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2002 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2012 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1004 : 2013 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 1004 : 1994 : REV A : R2003 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting |
| ASTM D 4000 : 2011 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6988 : 2003 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 5947 : 2011 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 5947 : 2018 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2004 : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 1004 : 2003 | Standard Test Method for Initial Tear Resistance of Plastic Film and Sheeting |
| ASTM D 1004 : 2007 | Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting |
| ASTM D 4000 : 2009 : REV B | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2000 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2006 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2010 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2007 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2009 : REV A | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6988 : 2007 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4000 : 2001 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2008 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5947 : 2003 | Standard Test Methods for Physical Dimensions of Solid Plastics Specimens |
| ASTM D 4000 : 2001 : REV A : EDT 1 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2004 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 6988 : 2013 | Standard Guide for Determination of Thickness of Plastic Film Test Specimens |
| ASTM D 4000 : 2010 | Standard Classification System for Specifying Plastic Materials |
| ASTM D 4000 : 2003 | Standard Classification System for Specifying Plastic Materials |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.