• There are no items in your cart

ASTM D 2172 : 2005

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Methods for Quantitative Extraction of Bitumen From Bituminous Paving Mixtures
Available format(s)

Hardcopy , PDF

Superseded date

11-11-2014

Language(s)

English

Published date

07-15-2005

CONTAINED IN VOL. 04.03, 2009 Includes quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. Aggregate obtained by these test methods may be used for sieve analysis using Test Method C 117 and Test Method C 136.

1.1 These test methods cover the quantitative determination of bitumen in hot-mixed paving mixtures and pavement samples. Aggregate obtained by these test methods may be used for sieve analysis using Test Method C 117 and Test Method C 136.

1.2 The values stated in inch-pound units are to be regarded as the standard. The values given in parentheses are for information only.

1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific hazards are given in Section 7.

Note 1—The results obtained by these test methods may be affected by the age of the material tested, with older samples tending to yield slightly lower bitumen content. Best quantitative results are obtained when the test is made on mixtures and pavements shortly after their preparation. It is difficult to remove all the asphalt when some aggregates are used and some chlorides may remain within the mineral matter affecting the measured asphalt content.

Committee
D 04
DevelopmentNote
Supersedes ASTM D 1097. (02/2002)
DocumentType
Test Method
Pages
12
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 4469 : 2017 : REDLINE Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures
ASTM D 3089 : 1997 : R2008 Standard Practice for Determining the A-D Dimension of Aerosol Valve Dip Tubes
ASTM D 6607 : 2000 : R2009 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits
ASTM D 5444 : 2015 : REDLINE Standard Test Method for Mechanical Size Analysis of Extracted Aggregate
ASTM D 6607 : 2000 : R2005 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits
UFC 3-260-03 : 2001 UNIFIED FACILITIES CRITERIA - AIRFIELD PAVEMENT EVALUATION
ASTM D 6608 : 2012 : REDLINE Standard Practice for the Identification of Trinidad Lake Asphalt in Asphalt Mixes
ASTM D 5710 : 2005 Standard Specification for Trinidad Lake Modified Asphalt
ASTM D 4215 : 2007 : R2013 Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures
ASTM D 6607 : 2000 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits
ASTM D 6995 : 2005 : R2013 Standard Test Method for Determining Field VMA based on the Maximum Specific Gravity of the Mix (G<inf>mm</inf>)
ASTM D 4887/D4887M : 2011 : R2016 Standard Practice for Preparation of Viscosity Blends for Hot Recycled Asphalt Materials
UFC 3-250-03 : 2001 UNIFIED FACILITIES CRITERIA - STANDARD PRACTICE MANUAL FOR FLEXIBLE PAVEMENTS
ASTM D 6995 : 2005 Standard Test Method for Determining Field VMA based on the Maximum Specific Gravity of the Mix (G<inf>mm</inf>)
API MPM CH8.1 SPANISH : 2013 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS
API MPM CH8.1 : 2013 MANUAL OF PETROLEUM MEASUREMENT STANDARDS - CHAPTER 8.1: STANDARD PRACTICE FOR MANUAL SAMPLING OF PETROLEUM AND PETROLEUM PRODUCTS
ASTM D 1856 : 2009 Standard Test Method for Recovery of Asphalt From Solution by Abson Method
ASTM D 5710/D5710M : 2015 : REDLINE Standard Specification for Trinidad Lake Modified Asphalt
ASTM D 6607 : 2000 : R2015 Standard Practice for Inclusion of Precision Statement Variation in Specification Limits
ASTM D 4887 : 1999 Standard Test Method for Preparation of Viscosity Blends for Hot Recycled Bituminous Materials
ASTM D 4469 : 2017 Standard Practice for Calculating Percent Asphalt Absorption by the Aggregate in Asphalt Mixtures
ASTM D 5444 : 2015 Standard Test Method for Mechanical Size Analysis of Extracted Aggregate
ASTM D 5710/D5710M : 2015 Standard Specification for Trinidad Lake Modified Asphalt
ASTM D 4057 : 2012 : R2018 Standard Practice for Manual Sampling of Petroleum and Petroleum Products
ASTM D 6608 : 2012 Standard Practice for the Identification of Trinidad Lake Asphalt in Asphalt Mixes
ASTM D 4383 : 2012-12 SPECIFICATION FOR PLOWABLE, RAISED RETROREFLECTIVE PAVEMENT MARKERS
ASTM D 1856 : 2009 : R2015 Standard Test Method for Recovery of Asphalt From Solution by Abson Method
ASTM D 4887/D4887M : 2011 Standard Practice for Preparation of Viscosity Blends for Hot Recycled Bituminous Materials
ASTM D 4215 : 2007 Standard Specification for Cold-Mixed, Cold-Laid Bituminous Paving Mixtures
ASTM D 3515 : 2001 Standard Specification for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures (Withdrawn 2009)

O-T-634 Revision C:1984 TRICHLOROETHYLENE, TECHNICAL
ASTM C 128 : 2015 : REDLINE Standard Test Method for Relative Density (Specific Gravity) and Absorption of Fine Aggregate
ASTM D 1461 : 2017 : REDLINE Standard Test Method for Moisture or Volatile Distillates in Asphalt Mixtures
ASTM C 136 : 2006 Standard Test Method for Sieve Analysis of Fine and Coarse Aggregates
ASTM C 117 : 2017 : REDLINE Standard Test Method for Materials Finer than 75-μm (No. 200) Sieve in Mineral Aggregates by Washing
ASTM C 670 : 2015 : REDLINE Standard Practice for Preparing Precision and Bias Statements for Test Methods for Construction Materials

View more information
US$83.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.