ASTM D 2303 : 2013
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Hardcopy , PDF
10-07-2020
English
04-01-2013
CONTAINED IN VOL. 10.01, 2015 Defines the evaluation of the relative tracking and erosion resistance of insulating solids using the liquid-contaminant, inclined-plane test.
1.1These test methods cover the evaluation of the relative tracking and erosion resistance of insulating solids using the liquid-contaminant, inclined-plane test.2 The following test methods also can be used to evaluate the tracking resistance of materials: D2132 (contaminants: dust and fog) and D3638 (contaminant: conductive liquid drops).
1.2Two tracking and one erosion test procedure are described:
1.2.3A method for quantitative determination of erosion (Annex A1).
1.3While a particular contaminant solution is specified, other concentrations of the same contaminant, or different contaminants are used to simulate different environmental or service conditions.
1.5This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Specific precautionary statements are given in Section 8.
| Committee |
D 09
|
| DocumentType |
Test Method
|
| Pages |
11
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy | |
| Supersedes |
| IEEE 1133-1988 | IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications |
| CSA C60044-8 : 2007 : R2016 | INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS |
| BS EN 61730-1 : 2007 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| IEEE 693-2005 | IEEE Recommended Practice for Seismic Design of Substations |
| ASTM D 3032 : 2016 : REDLINE | Standard Test Methods for Hookup Wire Insulation |
| CSA C22.2 No. 61730-1 : 2011 : INC : AMD 2 : 2015 : R2016 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| CSA C22.2 No. 61730-1 : 2011 : INC : AMD 1 : 2013 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| IEEE C37.23-2003 | IEEE Standard for Metal-Enclosed Bus |
| MIL-DTL-917 Revision F:2014 | ELECTRIC POWER EQUIPMENT, BASIC REQUIREMENTS FOR |
| CSA C60044-2 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 2: INDUCTIVE VOLTAGE TRANSFORMERS |
| CSA C60044-8 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS |
| CSA C22.2 No. 61730-1 : 2011 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| IEEE C37.20.2-2015 | IEEE Standard for Metal-Clad Switchgear |
| CSA C22.2 NO No. 298 : 2016 | HIGH VOLTAGE COUPLERS |
| IEEE DRAFT C57.12.44 : D2.1 2005 | REQUIREMENTS FOR SECONDARY NETWORK PROTECTORS |
| C22.2 NO. 4248.1-17 | Fuseholders Part 1: General requirements (Trinational standard with UL 4248-1 and NMX-J-009/4248/1-ANCE) |
| ANSI C37.57 : 1990 | SWITCHGEAR - METAL-ENCLOSED INTERRUPTER SWITCHGEAR ASSEMBLIES - CONFORMANCE TESTING |
| ANSI C37.55 : 1989 | MEDIUM VOLTAGE METAL-CLAD ASSEMBLIES - CONFORMANCE TEST PROCEDURES |
| MIL-P-24364 Base Document:1969 | PLASTIC SHEET, LAMINATED, THERMOSETTING, ELECTRICAL INSULATING SHEET, GLASS MAT |
| CSA C60044-2 : 2007 | INSTRUMENT TRANSFORMERS - PART 2: INDUCTIVE VOLTAGE TRANSFORMERS |
| CSA C60044-8 :2007 | INSTRUMENT TRANSFORMERS - PART 8: ELECTRONIC CURRENT TRANSFORMERS |
| ASTM D 709 : 2017 : REDLINE | Standard Specification for Laminated Thermosetting Materials |
| CSA C61869-1 : 2014 | INSTRUMENT TRANSFORMERS - PART 1: GENERAL REQUIREMENTS |
| ENA TS 09-13 : ISSUE 1 AMD 1 1993 | PERFORMANCE SPECIFICATION FOR HIGH VOLTAGE HEAT SHRINKABLE COMPONENTS FOR USE WITH HIGH VOLTAGE SOLID TYPES CABLES UP TO AND INCLUDING 33000 VOLTS |
| ESI 09-13 : ISSUE 1 | PERFORMANCE SPECIFICATION FOR HIGH VOLTAGE HEAT SHRINKABLE COMPONENTS FOR USE WITH HIGH VOLTAGE SOLID TYPE CABLES UP TO AND INCLUDING 33000 VOLTS |
| MIL-I-24768 Base Document:1992 | INSULATION, PLASTICS, LAMINATED, THERMOSETTING, GENERAL SPECIFICATION FOR |
| MIL-A-28768 Revision B:1984 | ANTENNA, FIXED HF, GENERAL SPECIFICATION FOR |
| MIL-A-28772 Revision C:1984 | ANTENNA, HF, FIXED ROTATABLE LOG PERIODIC |
| IEEE C57.12.44-2014 | IEEE Standard Requirements for Secondary Network Protectors |
| CSA C60044-1 : 2007 : R2011 | INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS |
| CSA C60044-1 : 2007 | INSTRUMENT TRANSFORMERS - PART 1: CURRENT TRANSFORMERS |
| CSA C22.2 No. 61730-1 : 2011 : INC : UPD 1 : 2013 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| ASTM D 495 : 2014 | Standard Test Method for High-Voltage, Low-Current, Dry Arc Resistance of Solid Electrical Insulation |
| CSA C22.2 No. 61730-1 : 2011 : INC : AMD 2 : 2015 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| ASTM D 2132 : 2012-02 | TEST METHOD FOR DUST-AND-FOG TRACKING AND EROSION RESISTANCE OF ELECTRICAL INSULATING MATERIALS |
| I.S. EN 61730-1:2007 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION |
| IEEE 1434-2014 | IEEE Guide for the Measurement of Partial Discharges in AC Electric Machinery |
| IEEE 1523-2002 | IEEE Guide for the Application, Maintenance, and Evaluation of Room Temperature Vulcanizing (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators |
| ASTM D 3032 : 2016 | Standard Test Methods for Hookup Wire Insulation |
| ASTM D 709 : 2017 | Standard Specification for Laminated Thermosetting Materials |
| ASTM D 229 : 2019 | Standard Test Methods for Rigid Sheet and Plate Materials Used for Electrical Insulation |
| IEEE C37.20.3-2013 REDLINE | IEEE Standard for Metal-Enclosed Interrupter Switchgear (1 kV-38 kV) |
| EN 61730-1:2007/A11:2014 | PHOTOVOLTAIC (PV) MODULE SAFETY QUALIFICATION - PART 1: REQUIREMENTS FOR CONSTRUCTION (IEC 61730-1:2004, MODIFIED) |
| ASTM D 2132 : 2012-02 | TEST METHOD FOR DUST-AND-FOG TRACKING AND EROSION RESISTANCE OF ELECTRICAL INSULATING MATERIALS |
| ASTM D 3638 : 2012 : REDLINE | Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials |
| ASTM D 2132 : 2012 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 1711 : 2002 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1711 : 2015 : REDLINE | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1711 : 2011 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 3638 : 2007 | Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials |
| ASTM D 1711 : 2011 : REV A | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1711 : 2013 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1711 : 1999 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 3638 : 2012 | Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials |
| ASTM D 1711 : 2014 : REV A | Standard Terminology Relating to Electrical Insulation |
| ASTM D 3638 : 1993 : R1998 | Standard Test Method for Comparative Tracking Index of Electrical Insulating Materials |
| ASTM D 1711 : 2015 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 1711 : 2014 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 2132 : 2019 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 2132 : 2003 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 1711 : 2020 | Standard Terminology Relating to Electrical Insulation |
| IEC 60587:2007 | Electrical insulating materials used under severe ambient conditions - Test methods for evaluating resistance to tracking and erosion |
| ASTM D 1711 : 2008 | Standard Terminology Relating to Electrical Insulation |
| ASTM D 2132 : 2011 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 2132 : 2012 : R2018 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 2132 : 1998 | Standard Test Method for Dust-and-Fog Tracking and Erosion Resistance of Electrical Insulating Materials |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.