ASTM D 2444 : 1999
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
View Superseded by
superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Method for Determination of the Impact Resistance of Thermoplastic Pipe and Fittings by Means of a Tup (Falling Weight)
Available format(s)
Hardcopy , PDF
Superseded date
11-11-2014
Language(s)
English
Published date
04-10-1999
1.1 This test method covers the determination of the impact resistance of thermoplastic pipe and fittings under specified conditions of impact by means of a tup (falling weight). Three interchangeable striking noses are used on the tup, differing in geometrical configuration. Two specimen holders are described.
1.2 The values stated in inch-pound units are to be regarded as the standard. The values in parentheses are provided for information purposes only.
1.3 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of whoever uses this standard to consult and establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
F 17
|
| DocumentType |
Test Method
|
| Pages |
8
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| SupersededBy |
| ASTM F 794:2003 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM D 6070 : 2002 | Standard Test Methods for Physical Properties of Smooth-Wall, Coilable, Polyethylene (PE) Conduit (Duct) for Preassembled Wire and Cable |
| ASTM F 1673 : 2010 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| CSA B45 SERIES : 2002 : R2013 | PLUMBING FIXTURES |
| NACE TM 01 96 : 0 | CHEMICAL RESISTANCE OF POLYMERIC MATERIALS BY PERIODIC EVALUATION |
| ASTM F 800 : 1989 | Specification for Corrugated Poly(Vinyl Chloride) (PVC) Tubing and Compatible Fittings (Withdrawn 1992) |
| ASTM F 3128 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
| SCTE 77 : 2013 | SPECIFICATION FOR UNDERGROUND ENCLOSURE INTEGRITY |
| ASTM F 725 : 2003 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| ASTM F 2881 : 2011 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 2390 : 2012 : R2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| ASTM D 3034 : 2016 : REDLINE | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM F 2881 : 2011 : R2015 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| CSA C22.2 No. 327 : 2016 | HDPE CONDUIT, CONDUCTORS-IN-CONDUIT, AND FITTINGS |
| ASTM F 892 : 1995 | Specification for Polyethylene (PE) Corrugated Pipe With a Smooth Interior and Fittings (Withdrawn 2001) |
| ASTM C 647 : 2008 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM D 6070 : 2002 : R2010 | Standard Test Methods for Physical Properties of Smooth-Wall, Coilable, Polyethylene (PE) Conduit (Duct) for Preassembled Wire and Cable (Withdrawn 2016) |
| ASTM F 2762 : 2011 : EDT 1 | Standard Specification for 12 to 30 in. (300 to 750 mm) Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications (Withdrawn 2016) |
| ASTM F 2947 : 2012 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2763 : 2016 : REDLINE | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| API 15S : 2016 | SPOOLABLE REINFORCED PLASTIC LINE PIPE |
| ASTM F 2158 : 2008 | Standard Specification for Residential Central-Vacuum Tube and Fittings |
| ASTM F 725 : 2003 : EDT 1 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| ASTM F 794 : 2003 : R2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM F 2658 : 2007 : R2019 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
| ASTM F 2986 : 2012 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| BS ISO 16149:2006 | Agricultural irrigation equipment. PVC above-ground low-pressure pipe for surface irrigation. Specifications and test methods |
| ASTM F 2658 : 2007 : R2013 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
| ASTM F 2987 : 2012 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications |
| AASHTO M 330 : 2013 | SPECIFICATION FOR POLYPROPYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| FM 1614 : 2017 | FIBER REINFORCED COMPOSITE (FRC) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| CSA B45 SERIES :2002 | PLUMBING FIXTURES |
| ASTM D 2665 : 2014 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| AASHTO M 304 : 2011 : R2015 | SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER |
| ASTM F 725 : 2003 : R2018 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| CSA B45.6 : 2011 | NONRECIRCULATING TOILETS, VACUUM TOILETS, AND WASTE-HOLDING TANKS FOR USE IN RECREATIONAL VEHICLES |
| ASTM F 2947/F2947M : 2019 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2648/F2648M : 2017 | Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications |
| ASTM F 667/F667M : 2016 | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM F 2881/F2881M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 3371 : 2019 | Standard Specification for Polyolefin Pipe and Fittings for Drainage, Waste, and Vent Applications |
| ASTM F 512 : 2012 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
| ASTM F 2763 : 2016 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Dual and Triple Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 1504 : 2014 | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| ASTM F 1760 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
| ASTM F 628 : 2012 : EDT 3 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe With a Cellular Core (Withdrawn 2021) |
| ASTM F 3128 : 2019 | Standard Specification for Poly(Vinyl Chloride) (PVC) Schedule 40 Drain, Waste, and Vent Pipe with a Cellular Core |
| ASTM F 1412 : 2016 | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 480 : 2014 | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM F 949 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM D 3034 : 2016 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM F 1483 : 2017 | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| ASTM F 3219 : 2019 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM E 2136 : 2004 : R2013 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings—Durability (Withdrawn 2022) |
| ASTM F 412 : 2019 | Standard Terminology Relating to Plastic Piping Systems |
| ASTM F 2306/F2306M : 2019 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Gravity-Flow Storm Sewer and Subsurface Drainage Applications |
| ASTM D 5628 : 2018 | Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimens by Means of a Falling Dart (Tup or Falling Mass) |
| ASTM F 2764/F2764M : 2019 | Standard Specification for 6 to 60 in. [150 to 1500 mm] Polypropylene (PP) Corrugated Double and Triple Wall Pipe and Fittings for Non-Pressure Sanitary Sewer Applications |
| ASTM F 758 : 2014 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
| ASTM D 2846/D2846M : 2019 : REV A | Standard Specification for Chlorinated Poly(Vinyl Chloride) (CPVC) Plastic Hot- and Cold-Water Distribution Systems |
| FM 1112 : 2006 | INDICATING VALVES (BUTTERFLY OR BALL TYPE) |
| ASTM C 647 : 2008 : R2013 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM F 1336 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM F 2658 : 2007 | Standard Specification for Type PSM Poly(Vinyl Chloride) (PVC) SDR 51 and SDR 64 Sewer Pipe and Fittings |
| ASTM F 1499 : 2017 : REDLINE | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| ASTM F 3219 : 2017 | Standard Specification for 3 to 30 in. (75 To 750 mm) Polypropylene (PP) Corrugated Single Wall Pipe and Fittings |
| ASTM F 480 : 2014 : REDLINE | Standard Specification for Thermoplastic Well Casing Pipe and Couplings Made in Standard Dimension Ratios (SDR), SCH 40 and SCH 80 |
| ASTM F 2562/F2562M : 2015 : REDLINE | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM F 512 : 2012 : R2017 | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Conduit and Fittings for Underground Installation |
| C22.2 NO. 83.1-07 (R2017) | Electrical Metallic Tubing - Steel (Tri-National Standard, with UL 797 and NMX-J-536-ANCE-2007) |
| NEMA TC 6&8 : 2013 | POLYVINYL CHLORIDE (PVC) PLASTIC UTILITIES DUCT FOR UNDERGROUND INSTALLATIONS |
| NEMA TC 12 : 1991 | CORRUGATED POLYVINYL CHLORIDE (PVC) COILABLE PLASTIC UTILITIES DUCT |
| NEMA TC 10 : 1993 | PVC PLASTIC COMMUNICATIONS DUCT AND FITTINGS FOR UNDERGROUND INSTALLATION |
| ASTM D 2949 : 2018 | Standard Specification for 3.25-in. Outside Diameter Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| AASHTO R 63 : 2013 | PRACTICE FOR SOLID WALL HIGH-DENSITY POLYETHYLENE (HDPE) CONDUIT FOR NON-PRESSURE APPLICATIONS USED FOR THE PROTECTION OF POWER AND TELECOMMUNICATIONS CABLES |
| NEMA TC 8 : 1999 | PVC PLASTIC UTILITIES DUCT FOR UNDERGROUND INSTALLATIONS |
| NEMA TC 5 : 1990 | CORRUGATED POLYOLEFIN COILABLE PLASTIC UTILITIES DUCT |
| NEMA TC 15 : 1993 | CORRUGATED POLYVINYL CHLORIDE (PVC) FIBER OPTIC INNERDUCT |
| NSF 24 : 2015 | PLUMBING SYSTEM COMPONENTS FOR RECREATIONAL VEHICLES |
| API 15LT : 1993 | SPECIFICATION FOR PVC LINED STEEL TUBULAR GOODS |
| ASTM F 725 : 2003 : R2008 : EDT 1 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| AASHTO M 278 : 2015 | SPECIFICATION FOR CLASS PS46 POLY(VINYL CHLORIDE) (PVC) PIPE |
| ASTM F 725 : 2003 : R2013 | Standard Practice for Drafting Impact Test Requirements In Thermoplastic Pipe And Fittings Standards |
| AASHTO MP 20 : 2013 | SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| ASTM F 949 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Corrugated Sewer Pipe With a Smooth Interior and Fittings |
| ASTM F 2562/F2562M : 2015 | Specification for Steel Reinforced Thermoplastic Ribbed Pipe and Fittings for Non-Pressure Drainage and Sewerage |
| ASTM F 2176 : 2017 | Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct |
| ASTM D 2241 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| ASTM F 1499 : 2017 | Standard Specification for Coextruded Composite Drain, Waste, and Vent Pipe (DWV) |
| ASTM F 1336 : 2015 | Standard Specification for Poly(Vinyl Chloride) (PVC) Gasketed Sewer Fittings |
| ASTM F 2817 : 2013 : R2019 | Standard Specification for Poly (Vinyl Chloride) (PVC) Gas Pressure Pipe and Fittings For Maintenance or Repair |
| ASTM D 2661 : 2014 : EDT 1 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Schedule 40 Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 891 : 2016 | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM F 679 : 2016 | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| ASTM F 1871 : 2018 | Standard Specification for Folded/Formed Poly (Vinyl Chloride) Pipe Type A for Existing Sewer and Conduit Rehabilitation |
| ASTM C 647 : 2019 | Standard Guide to Properties and Tests of Mastics and Coating Finishes for Thermal Insulation |
| ASTM F 1901 : 2016 | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| ASTM F 1488 : 2014 : R2019 | Standard Specification for Coextruded Composite Pipe |
| ASTM D 2665 : 2014 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent Pipe and Fittings |
| ASTM F 2176 : 2017 : REDLINE | Standard Specification for Mechanical Couplings Used on Polyethylene Conduit, Duct and Innerduct |
| ASTM F 2947 : 2012 : EDT 1 | Standard Specification for 150 to 1500 mm [6 to 60 in.] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| CSA B137 COMPENDIUM : 2017 | THERMOPLASTIC PRESSURE PIPING COMPENDIUM |
| CSA C22.2 No. 45.1 :2007 | ELECTRICAL RIGID METAL CONDUIT - STEEL |
| CSA C22.2 No. 45.1 : 2007 : INC : UPD 1 : 2010 | ELECTRICAL RIGID METAL CONDUIT - STEEL |
| CSA C22.2 No. 45.1 : 2007 : FR | ELECTRICAL RIGID METAL CONDUIT - STEEL |
| ASTM G 125 : 2000 : R2008 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| ASTM D 2751 : 2005 | Standard Specification for Acrylonitrile-Butadiene-Styrene (ABS) Sewer Pipe and Fittings (Withdrawn 2014) |
| CSA B1800 SERIES : 2015 | THERMOPLASTIC NON-PRESSURE PIPING COMPENDIUM |
| ASTM F 1412 : 2016 : REDLINE | Standard Specification for Polyolefin Pipe and Fittings for Corrosive Waste Drainage Systems |
| ASTM F 679 : 2016 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Large-Diameter Plastic Gravity Sewer Pipe and Fittings |
| ASTM F 1760 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Non-Pressure Plastic Pipe Having Reprocessed-Recycled Content |
| CSA C22.2 No. 83.1 : 2007 | ELECTRICAL METALLIC TUBING - STEEL |
| CSA C22.2 No. 83.1 : 2007 : INC : UPD 1 : 2012 : R201200 | ELECTRICAL METALLIC TUBING - STEEL |
| CSA C22.2 No. 227.2.1 : 2014 | LIQUID-TIGHT FLEXIBLE NONMETALLIC CONDUIT |
| CSA B182.7 : 2006 | PSM TYPE MULTILAYER POLYVINYLCHLORIDE (PVC) SEWER PIPE HAVING REPROCESSED-RECYCLED CONTENT |
| ASTM F 1803 : 2015 | Standard Specification for Poly (Vinyl Chloride)(PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter |
| ASTM D 2750 : 1995 | Specification for Acrylonitrile- Butadiene-Sytrene (ABS) Plastics Utilities Conduit and Fittings (Withdrawn 1997) |
| ASTM D 2852 : 2016 | Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings (Withdrawn 2022) |
| ASTM G 125 : 2000 : R2015 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| (INACTIVE RECORD)CSA B45 SERIES:2002 | PLUMBING FIXTURES |
| CSA B45.6 : 2011 : R2016 | NONRECIRCULATING TOILETS, VACUUM TOILETS, AND WASTE-HOLDING TANKS FOR USE IN RECREATIONAL VEHICLES |
| ISO 16149:2006 | Agricultural irrigation equipment PVC above-ground low-pressure pipe for surface irrigation Specifications and test methods |
| C22.2 NO. 45.1-07 (R2017) | Electrical Rigid Metal Conduit - Steel (Tri-National standard, with UL 6 and NMX-J-534-ANCE-2007) |
| CSA C22.2 No. 45.1 : 2007 : INC : UPD 2 : 2014 : R201200 | ELECTRICAL RIGID METAL CONDUIT - STEEL |
| AASHTO MP 20 : 2013 : R2014 | SPECIFICATION FOR STEEL-REINFORCED POLYETHYLENE (PE) RIBBED PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| ASTM F 2762 : 2011 | Standard Specification for 12 to 30 in. [300 to 750 mm] Annular Corrugated Profile-Wall Polyethylene (PE) Pipe and Fittings for Sanitary Sewer Applications |
| ASTM F 2307 : 2003 | Standard Specification for Series 10 Poly(Vinyl Chloride) (PVC) Closed Profile Gravity Pipe and Fittings Based on Controlled Inside Diameter (Withdrawn 2011) |
| ASTM F 1483 : 2017 : REDLINE | Standard Specification for Oriented Poly(Vinyl Chloride), PVCO, Pressure Pipe |
| ASTM F 1732 : 2012 : R2018 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer and Drain Pipe Containing Recycled PVC Material |
| ASTM F 2618 : 2019 | Standard Specification for Chlorinated Poly (Vinyl Chloride) (CPVC) Pipe and Fittings for Chemical Waste Drainage Systems |
| ASTM F 2987 : 2012 : R2018 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Heap Leach Aeration Applications (Withdrawn 2024) |
| ASTM F 1901 : 2016 : REDLINE | Standard Specification for Polyethylene (PE) Pipe and Fittings for Roof Drain Systems |
| FM 1612 : 2016 | POLYVINYL CHLORIDE (PVC) PIPE AND FITTING FOR UNDERGROUND FIRE PROTECTION SERVICE |
| ASTM F 667/F667M : 2016 : REDLINE | Standard Specification for 3 through 24 in. Corrugated Polyethylene Pipe and Fittings |
| ASTM F 2158 : 2008 : R2016 | Standard Specification for Residential Central-Vacuum Tube and Fittings |
| ASTM F 1504 : 2014 : REDLINE | Standard Specification for Folded Poly(Vinyl Chloride) (PVC) Pipe for Existing Sewer and Conduit Rehabilitation |
| CSA C22.2 No. 227.2 : 1993 | FLEXIBLE LIQUID-TIGHT NONMETALLIC CONDUIT |
| ASTM F 1871 : 2011-06 | SPECIFICATION FOR FOLDED/FORMED POLY (VINYL CHLORIDE) PIPE TYPE A FOR EXISTING SEWER AND CONDUIT REHABILITATION |
| CSA C22.2 No. 227.3 : 2015 | MECHANICAL PROTECTION TUBING (MPT) AND FITTINGS |
| ASTM E 2136 : 2004 | Standard Guide for Specifying and Evaluating Performance of Single Family Attached and Detached Dwellings-Durability |
| ASTM D 3485 : 2015 | Standard Specification for Coilable High Density Polyethylene (HDPE) Cable in Conduit (CIC) |
| CSA B45.10 : 2012 | HYDROMASSAGE BATHTUB SYSTEMS |
| AWWA M23 : 2 | PVC PIPE - DESIGN AND INSTALLATION |
| FM 1613 : 2017 | POLYETHYLENE (PE) PIPE AND FITTINGS FOR UNDERGROUND FIRE PROTECTION SERVICE |
| ABS 0063 : 2018 COR 2018 | RULES FOR BUILDING AND CLASSING FACILITIES ON OFFSHORE INSTALLATIONS |
| ASTM F 2648/F2648M : 2017 : REDLINE | Standard Specification for 2 to 60 inch [50 to 1500 mm] Annular Corrugated Profile Wall Polyethylene (PE) Pipe and Fittings for Land Drainage Applications |
| ASTM F 810 : 2012 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM F 2390:2012 | Standard Specification for Poly(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Vent (DWV) Pipe and Fittings Having Post-Industrial Recycle Content |
| AASHTO M 304 : 2011 | SPECIFICATION FOR POLY(VINYL CHLORIDE) (PVC) PROFILE WALL DRAIN PIPE AND FITTINGS BASED ON CONTROLLED INSIDE DIAMETER |
| CSA C22.2 No. 45.1 : 2007 : INC : UPD 1 : 2010 : R2012 | ELECTRICAL RIGID METAL CONDUIT - STEEL |
| ASTM D 2852 : 2016 : REDLINE | Standard Specification for Styrene-Rubber (SR) Plastic Drain Pipe and Fittings |
| ASAE S376.1 : 1992 | DESIGN, INSTALLATION AND PERFORMANCE OF UNDERGROUND, THERMOPLASTIC IRRIGATION PIPELINES |
| AASHTO M 294 : 2015 | SPECIFICATION FOR CORRUGATED POLYETHYLENE PIPE, 300- TO 1500-MM (12- TO 60-IN.) DIAMETER |
| ASTM F 2881/F2881M : 2018 | Standard Specification for 12 to 60 in. [300 to 1500 mm] Polypropylene (PP) Dual Wall Pipe and Fittings for Non-Pressure Storm Sewer Applications |
| ASTM F 810 : 2012 : R2018 | Standard Specification for Smoothwall Polyethylene (PE) Pipe for Use in Drainage and Waste Disposal Absorption Fields |
| ASTM F 2160 : 2016 | Standard Specification for Solid Wall High Density Polyethylene (HDPE) Conduit Based on Controlled Outside Diameter (OD) |
| ASTM D 2729 : 2017 | Standard Specification for Poly(Vinyl Chloride) (PVC) Sewer Pipe and Fittings |
| ASTM F 891 : 2016 : REDLINE | Standard Specification for Coextruded Poly(Vinyl Chloride) (PVC) Plastic Pipe With a Cellular Core |
| ASTM F 2947/F2947M : 2014-03 | SPECIFICATION FOR 150 TO 1500 MM [6 TO 60 IN.] ANNULAR CORRUGATED PROFILE-WALL POLYETHYLENE (PE) PIPE AND FITTINGS FOR SANITARY SEWER APPLICATIONS |
| ASTM F 1673 : 2010 : R2016 | Standard Specification for Polyvinylidene Fluoride (PVDF) Corrosive Waste Drainage Systems |
| ASTM F 758 : 2014 : REDLINE | Standard Specification for Smooth-Wall Poly(Vinyl Chloride) (PVC) Plastic Underdrain Systems for Highway, Airport, and Similar Drainage |
| ASTM D 2241 : 2015 : REDLINE | Standard Specification for Poly(Vinyl Chloride) (PVC) Pressure-Rated Pipe (SDR Series) |
| ASTM F 2986 : 2012 : R2017 | Standard Specification for Corrugated Polyethylene Pipe and Fittings for Mine Leachate Applications |
| ASTM G 125 : 2000 | Standard Test Method for Measuring Liquid and Solid Material Fire Limits in Gaseous Oxidants |
| ASTM F 2158 : 2008 : R2013 | Standard Specification for Residential Central-Vacuum Tube and Fittings |
| ASTM F 794 : 2003 : R2009 | Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Gravity Sewer Pipe and Fittings Based on Controlled Inside Diameter |
| ASME A112.19.7-2012/CSA B45.10-12 (R2017) | Hydromassage bathtub systems |
| ASME B16.40 : 2013 | MANUALLY OPERATED THERMOPLASTIC GAS SHUTOFFS AND VALVES IN GAS DISTRIBUTION SYSTEMS |
| ASME A112.4.4 : 2017 | PLASTIC PUSH-FIT DRAIN, WASTE, AND VENT (DWV) FITTINGS |
| ASME A112.19.7 : 2012 : R2017 | HYDROMASSAGE BATHTUB SYSTEMS |
| ASME A112.19.8 : 2007 | SUCTION FITTINGS FOR USE IN SWIMMING POOLS, WADING POOLS, SPAS, AND HOT TUBS |
| ASME A112.19.7 : 2012 | HYDROMASSAGE BATHTUB SYSTEMS |
US$75.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
Hardcopy - English
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.