ASTM D 257 : 2014 : REDLINE
Superseded
Superseded
A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.
Standard Test Methods for DC Resistance or Conductance of Insulating Materials
Available format(s)
PDF
Superseded date
05-19-2021
Language(s)
English
Published date
05-27-2014
CONTAINED IN VOL. 10.01, 2017 Describes direct-current procedures for the measurement of dc insulation resistance, volume resistance and surface resistance.
1.1These test methods cover direct-current procedures for the measurement of dc insulation resistance, volume resistance, and surface resistance. From such measurements and the geometric dimensions of specimen and electrodes, both volume and surface resistivity of electrical insulating materials can be calculated, as well as the corresponding conductances and conductivities.
1.2These test methods are not suitable for use in measuring the electrical resistance/conductance of moderately conductive materials. Use Test Method D4496 to evaluate such materials.
1.3This standard describes several general alternative methodologies for measuring resistance (or conductance). Specific materials can be tested most appropriately by using standard ASTM test methods applicable to the specific material that define both voltage stress limits and finite electrification times as well as specimen configuration and electrode geometry. These individual specific test methodologies would be better able to define the precision and bias for the determination.
1.4This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.
| Committee |
D 09
|
| DocumentType |
Redline
|
| Pages |
26
|
| PublisherName |
American Society for Testing and Materials
|
| Status |
Superseded
|
| Standards | Relationship |
| ISO 1325:1973 | Corresponds |
| MIL-C-47224 Revision B:1993 | COMPOUND, MOLDING, TRANSFER, EPOXY RESIN, SINGLE COMPONENT |
| 15/30291972 DC : 0 | BS EN ISO 14692-4 - PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 4: FABRICATION, INSTALLATION AND OPERATION |
| ASTM F 79 : 1969 : R2000 | Standard Specification for Type 101 Sealing Glass |
| I.S. EN 62788-1-2:2016 | MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - PART 1-2: ENCAPSULANTS - MEASUREMENT OF VOLUME RESISTIVITY OF PHOTOVOLTAIC ENCAPSULANTS AND OTHER POLYMERIC MATERIALS |
| ASTM D 707 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Butyrate Molding and Extrusion Compounds (CAB) |
| MIL-A-46146 Revision B:1990 | ADHESIVE-SEALANTS, SILICONE, RTV, NONCORROSIVE (FOR USE WITH SENSITIVE METALS AND EQUIPMENT) |
| ANSI/AWWA C213 : 2015 | FUSION-BONDED EPOXY COATINGS AND LININGS FOR STEEL WATER PIPE AND FITTINGS |
| MIL C 47176 : NOTICE 1 | COATING, SURFACE MOISTURE CURING POLYURETHANE |
| IEEE 386-2016 REDLINE | IEEE Standard for Separable Insulated Connector Systems for Power Distribution Systems Rated 2.5 kV through 35 kV |
| EN ISO 18797-1:2017 | Petroleum, petrochemical and natural gas industries - External corrosion protection of risers by coatings and linings - Part 1: Elastomeric coating systems-polychloroprene or EPDM (ISO 18797-1:2016) |
| MIL-A-46106 Revision B:1989 | ADHESIVE-SEALANTS, SILICONE, RTV, ONE-COMPONENT |
| L-P-535 Revision E:1979 | PLASTIC SHEET (SHEETING): PLASTIC STRIP: POLY(VINYL CHLORIDE) AND POLY(VINYL CHLORIDE-VINYL ACETATE), RIGID |
| MIL-PRF-46846 Revision D:2013 | Rubber, Synthetic, Heat - Shrinkable |
| MIL-T-17128 Revision C:1982 | TRANSDUCER FLUID,SONAR |
| MIL-I-81550 Revision C:1983 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, REVERSION RESISTANT SILICONE |
| MIL-PRF-32584 Base Document:2017 | Deck Covering Materials, Monolithic |
| ASTM D 4923 : 2001 | Standard Specification for Reinforced Thermosetting Plastic Poles (Withdrawn 2010) |
| 15/30321951 DC : 0 | BS ISO 20195 - STANDARD PRACTICE - GUIDE FOR DESIGN FOR ADDITIVE MANUFACTURING |
| MIL-M-48245 Revision B:1988 | MOLDING COMPOUND, HOUSING |
| MIL-C-47002 Revision A:1991 | COATING, POLYURETHANE, SINGLE COMPONENT SYSTEM |
| 15/30278562 DC : 0 | BS ISO 18797-1 - PETROLEUM, PETROCHEMICALS AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMS - POLYCHLOROPRENE OR EPDM |
| 16/30338304 DC : 0 | BS ISO/ASTM 52903-1 - ADDITIVE MANUFACTURING - STANDARD SPECIFICATION FOR MATERIAL EXTRUSION BASED ADDITIVE MANUFACTURING OF PLASTIC MATERIALS - PART 1: FEEDSTOCK MATERIALS |
| MIL-A-87135 Base Document:1979 | ADHESIVES, NON-CONDUCTIVE, FOR ELECTRONICS APPLICATION |
| 15/30331587 DC : 0 | BS EN 61189-5-503 - TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARDS AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 5-503: GENERAL TEST METHODS FOR MATERIALS AND ASSEMBLIES - CONDUCTIVE ANODIC FILAMENTS (CAF) TESTING OF CIRCUIT BOARDS |
| ASTM D 2442 : 1975 : R2012 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| MIL-PRF-47009 Revision D:2006 | COMPOUND, SILICONE, HEAT SINK |
| MIL-P-46185 Base Document:1983 | PLASTIC MOLDING & EXTRUSION MATERIALS, POLYETHERSULFONE |
| ANSI INCITS 121 : 1984 : R2006 | TWO-SIDED, UNFORMATTED, 8-INCH (200-MM), 48-TPI, DOUBLE-DENSITY, FLEXIBLE, DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 13 262 FTPR TWO-HEADED APPLICATION |
| ANSI INCITS 171 : 1989 : R2005 | ONE- AND TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 90-MM (3.5 IN), 5,3-TPMM (135-TPI) FLEXIBLE DISK CARTRIDGE FOR 15916 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| L-P-1041 Revision A:1973 | PLASTIC MOLDING AND EXTRUSION MATERIAL, VINYLIDENE CHLORIDE VINYL CHLORIDE COPOLYMER |
| ASTM D 116 : 1986 : R2016 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ISO 14692-4:2017 | Petroleum and natural gas industries — Glass-reinforced plastics (GRP) piping — Part 4: Fabrication, installation and operation |
| ASTM C 657 : 1993 : R2008 | Standard Test Method for D-C Volume Resistively of Glass |
| I.S. EN ISO 18797-1:2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMS-POLYCHLOROPRENE OR EPDM (ISO 18797-1:2016) |
| SAE AMS C 27725 : 2016 | COATING, CORROSION PREVENTATIVE, FOR AIRCRAFT INTEGRAL FUEL TANKS, FOR USE TO 250 DEGREES F (121 DEGREES C) |
| PD CLC/TR 60079-32-1:2015 | Explosive atmospheres Electrostatic hazards, guidance |
| ASTM D 3032 : 2016 : REDLINE | Standard Test Methods for Hookup Wire Insulation |
| ASTM D 1304 : 1999 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM D 116 : 1986 : R2011 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ASTM D 1248 : 2016 : REDLINE | Standard Specification for Polyethylene Plastics Extrusion Materials for Wire and Cable |
| ASTM F 602 : 2009 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
| ASTM D 788 : 2016 : REDLINE | Standard Classification System for Poly(Methyl Methacrylate) (PMMA) Molding and Extrusion Compounds |
| ASTM D 7201 : 2006 : R2011 | Standard Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in the Workplace, by Phase Contrast Microscopy (with an Option of Transmission Electron Microscopy) |
| ASTM D 6779 : 2017 : REDLINE | Standard Classification System for and Basis of Specification for Polyamide Molding and Extrusion Materials (PA) |
| ASTM D 176 : 2007 : R2012 | Standard Test Methods for Solid Filling and Treating Compounds Used for Electrical Insulation (Withdrawn 2013) |
| ASTM D 176 : 2007 | Standard Test Methods for Solid Filling and Treating Compounds Used for Electrical Insulation |
| ASTM G 21 : 2015 : REDLINE | Standard Practice for Determining Resistance of Synthetic Polymeric Materials to Fungi |
| ASTM D 6411/D6411M : 1999 : R2005 | Standard Specification for Slicone Rubber Room Temperature Vulcanizing Low Outgassing Materials |
| ASTM F 2468 : 2005 : R2011 | Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications |
| ASTM D 1039 : 2016 : REDLINE | Standard Test Methods for Glass-Bonded Mica Used as Electrical Insulation |
| ASTM F 105 : 1972 : R2000 | Standard Specification for Type 58 Borosilicate Sealing Glass |
| MIL-STD-883 Revision K:2016 | TEST METHOD STANDARD - MICROCIRCUITS |
| I.S. EN 14617-13:2013 | AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY |
| DIN EN ISO 21178:2013-09 | LIGHT CONVEYOR BELTS - DETERMINATION OF ELECTRICAL RESISTANCES (ISO 21178:2013) |
| EN 61189-5-503:2017 | Test methods for electrical materials, printed board and other interconnection structures and assemblies - Part 5-503: General test method for materials and assemblies - Conductive anodic filaments (CAF) testing of circuit boards |
| EN 62788-1-2:2016 | Measurement procedures for materials used in photovoltaic modules - Part 1-2: Encapsulants - Measurement of volume resistivity of photovoltaic encapsulants and other polymeric materials |
| IPC AJ 820 : A | ASSEMBLY AND JOINING HANDBOOK |
| MIL-P-46131 Revision B:1975 | PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYPHENYLENE OXIDE, MODIFIED, GLASS FIBER REINFORCED |
| MIL-I-24683 Revision A:1990 | INSULATION ELECTRICAL, HIGH TEMPERATURE INORGANIC PAPER |
| MIL-P-46144 Revision C:1986 | PLASTIC SHEET, POLYCARBONATE |
| MIL-P-46179 Revision A:1986 | PLASTIC MOLDING AND EXTRUSION MATERIAL, POLYAMIDE IMIDE |
| DOD I 24683 : 1987 | INSULATION ELECTRICAL, HIGH TEMPERATURE INORGANIC PAPER |
| MIL-P-46847 Revision B:1984 | PLASTIC MATERIAL, FOAMED POLYURETHANE FOR ENCAPSULATING ELECTRONIC COMPONENTS |
| S.R. CLC/TR 60079-32-1:2015 | EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS - GUIDANCE |
| MIL-I-23594 Revision C:1988 | INSULATION TAPE, ELECTRICAL, HIGH TEMPERATURE, POLYTETRAFLUOROETHYLENE, PRESSURE SENSITIVE |
| ISO 15840:2004 | Ships and marine technology Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications |
| SAE AMS 3733 : 2015 | POTTING COMPOUND, EPOXY, TWO PART, HIGHLY FILLED, HEAT CURE, HIGH COMPRESSIVE STRENGTH |
| MIL R 46846 : B | RUBBER, SYNTHETIC, HEAT-SHRINKABLE |
| MIL-S-8660 Revision C:1983 | SILICONE COMPOUND, NATO CODE NUMBER S 736 |
| 14/30300605 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| MIL C 47009 : B | COMPOUND, SILICONE, HEAT SINK |
| BS ISO 18797-1 : 2016 COR 2017 | PETROLEUM, PETROCHEMICAL AND NATURAL GAS INDUSTRIES - EXTERNAL CORROSION PROTECTION OF RISERS BY COATINGS AND LININGS - PART 1: ELASTOMERIC COATING SYSTEMSPOLYCHLOROPRENE OR EPDM |
| MIL S 8516 : F | SEALING COMPOUND, POLYSULFIDE RUBBER, ELECTRIC CONNECTORS AND ELECTRICAL SYSTEMS CHEMICALLY CURED |
| MIL-I-81765 Revision A:1987 | INSULATING COMPONENT, MOLDED, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR |
| MIL-HDBK-510 Revision A:2014 | AEROSPACE FUELS CERTIFICATION |
| CSA C22.2 No. 0.17 : 2000 : R2013 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
| ASTM D 1304 : 1999 : R2005 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| MIL-I-16923 Revision H:1991 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, EPOXY |
| MIL-STD-1904 Revision B:2016 | Test Standards for Level A and Level B Packaging for Conventional Ammunition |
| L-P-523 Revision D:1979 | PLASTIC SHEET AND FILM, FEP-FLUOROCARBON, EXTRUDED |
| ASTM F 624 : 2009 : R2015 : EDT 1 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
| MIL-P-46067 Revision B:1977 | PLASTIC EMBEDDING COMPOUND, EPOXY RESIN SYSTEM |
| MIL-PRF-62563 Revision B:2010 | FAN, VENTILATING, VEHICULAR COMPARTMENT |
| ASTM D 3222 : 2005 : R2015 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| MMM-A-1931 Base Document:1975 | ADHESIVE EPOXY SILVER FILLED, CONDUCTIVE |
| ASTM F 1837M : 1997 : R2007 | Standard Specification for Heat-Shrink Cable Entry Seals (Metric) |
| ASTM D 1562 : 2015 : REDLINE | Standard Classification System and Basis for Specification for Cellulose Acetate Propionate Molding and Extrusion Compounds (CAP) |
| ASTM D 6411/D6411M:1999 | Standard Specification for Slicone Rubber Room Temperature Vulcanizing Low Outgassing Materials |
| SAE AMS 3613 : 2016 | FILM, COPPER CLAD POLYESTER |
| 08/30183777 DC : DRAFT JUNE 2008 | BS IEC 61340-4-8 - ELECTROSTATICS - PART 4-8: STANDARD TEST METHODS FOR SPECIFIC APPLICATIONS - DISCHARGE SHIELDING - BAGS |
| IEC TR 62392:2006 | Suitability of typical electrical insulating material (EIM) for polymer recycling |
| ANSI INCITS 162 : 1988 : R1999 | INFORMATION SYSTEMS - TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 5.25-INCH (130-MM), 96-TPI (3,8 TPMM), FLEXIBLE DISK CARTRIDGE FOR 13 262 FTPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| BS EN IEC 61189-5-503:2017 | Test methods for electrical materials, printed board and other interconnection structures and assemblies General test method for materials and assemblies. Conductive anodic filaments (CAF) testing of circuit boards |
| ASTM F 635 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Liquid Thermoset Encapsulating Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
| MIL B 81705 : C | BARRIER MATERIALS, FLEXIBLE, ELECTROSTATIC FREE HEAT SEALABLE |
| SAE AMS P 46144 : 2015 | PLASTIC SHEET, POLYCARBONATE |
| MIL-PRF-81705 Revision E:2009 | Barrier Materials, Flexible, Electrostatic Discharge Protective, Heat-Sealable |
| CSA Z662 PACKAGE : 2011 | CONSISTS OF Z662-11, OIL AND GAS PIPELINE SYSTEMS AND Z662.1-11, COMMENTARY ON CSA Z662-11, OIL AND GAS PIPELINE SYSTEMS |
| SAE AMS P 46112 : 2002(S2015) | PLASTIC SHEET AND STRIP, POLYIMIDE |
| EN IEC 62688:2018 | Concentrator photovoltaic (CPV) modules and assemblies - Safety qualification |
| ANSI/AWWA C216 : 2015 | HEAT-SHRINKABLE CROSS-LINKED POLYOLEFIN COATINGS FOR STEEL WATER PIPE AND FITTINGS |
| ANSI INCITS 126 : 1986 : R2002 | INFORMATION TECHNOLOGY - ONE- AND TWO-SIDED DOUBLE DENSITYUNFORMATTED 5.25 INCH (130 MM) 96 TRACKS PER INCH (3.8 TRACKS PER MM) FLEXIBLE DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 7958 BPR USE |
| ASTM D 116 : 1986 : R2006 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ASTM F 105 : 1972 : R2010 | Standard Specification for Type 58 Borosilicate Sealing Glass |
| I.S. EN 16603-35-06:2014 | SPACE ENGINEERING - CLEANLINESS REQUIREMENTS FOR SPACECRAFT PROPULSION HARDWARE |
| ASTM F 79 : 1969 : R2015 | Standard Specification for Type 101 Sealing Glass |
| SAE AS 81550A : 2014 | INSULATING COMPOUND, ELECTRICAL, EMBEDDING, REVERSION RESISTANT SILICONE |
| ASTM F 665 : 2009 : R2015 | Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application |
| ASTM F 1837M : 1997 : R2012 : EDT 1 | Standard Specification for Heat-Shrink Cable Entry Seals (Metric) |
| ASTM C 657 : 1993 : R2003 | Standard Test Method for D-C Volume Resistively of Glass |
| ASTM D 4731 : 2013 : REDLINE | Standard Specification for Hot-Application Filling Compounds for Telecommunications Wire and Cable |
| ASTM D 3004 : 2008 | Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor and Insulation Shielding Materials |
| ASTM D 1458 : 2013-12 | TEST METHODS FOR FULLY CURED SILICONE RUBBER-COATED GLASS FABRIC AND TAPES FOR ELECTRICAL INSULATION |
| ASTM D 5575 : 2007 : R2013 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 8065/D8065M : 2016 | Standard Classification System and Basis for Specification for Specifying Plastic Films |
| CSA C22.2 No. 0.17 : 2000 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
| ASTM D 2287 : 2012 : REDLINE | Standard Specification for Nonrigid Vinyl Chloride Polymer and Copolymer Molding and Extrusion Compounds |
| ASTM D 2442 : 1975 : R2001 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| ASTM D 4000 : 2016 : REDLINE | Standard Classification System for Specifying Plastic Materials |
| ASTM D 5575 : 2007 | Standard Classification System for Copolymers of Vinylidene Fluoride (VDF) with Other Fluorinated Monomers |
| ASTM D 6585 : 2017 : REDLINE | Standard Specification for Unsintered Polytetrafluoroethylene (PTFE) Extruded Film or Tape |
| ASTM F 641 : 2009 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
| ASTM D 295 : 2012 | Standard Test Methods for Varnished Cotton Fabrics Used for Electrical Insulation (Withdrawn 2020) |
| ASTM D 4066 : 2013 | Standard Classification System for Nylon Injection and Extrusion Materials (PA) |
| ASTM D 345 : 2002 | Side bearings of the freight wagon bogies. General specifications |
| CSA C22.2 No. 198.3 : 2005 : R2014 | COATED ELECTRICAL SLEEVING |
| CSA C22.2 No. 198.3 : 2005 : R2010 | COATED ELECTRICAL SLEEVING |
| CSA C22.2 No. 249 : 1996 : R2011 | STANDARD TESTS FOR DETERMINING COMPATIBILITY OF CABLE-PULLING LUBRICANTS WITH WIRE AND CABLE |
| CSA C22.2 No. 249 : 1996 : R2015 | STANDARD TESTS FOR DETERMINING COMPATIBILITY OF CABLE-PULLING LUBRICANTS WITH WIRE AND CABLE |
| ANSI C37.57 : 1990 | SWITCHGEAR - METAL-ENCLOSED INTERRUPTER SWITCHGEAR ASSEMBLIES - CONFORMANCE TESTING |
| NEMA WC 55 : 1992(R1999) | INSTRUMENTATION CABLES AND THERMOCOUPLE WIRE |
| WC 3-1992 | RUBBER-INSULATED WIRE AND CABLE FOR THE TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY |
| WC 4-1988/ICEA S-65-375 3rd Ed. (R1993) | VARNISHED-CLOTH-INSULATED WIRE AND CABLE FOR THE TRANSMISSION AND DISTRIBUTION OF ELECTRICAL ENERGY |
| ANSI C37.55 : 1989 | MEDIUM VOLTAGE METAL-CLAD ASSEMBLIES - CONFORMANCE TEST PROCEDURES |
| ANSI/NEMA FI 3:2004 | Calendered Aramid Papers Used for Electrical Insulation |
| NEMA HP 100:1991(R2010) | High-Temperature Instrumentation and Control Cables |
| BS EN 61122:1994 | Specification for still video floppy disk magnetic recording system |
| MIL-DTL-83723-27 Revision C:2015 | CONNECTORS, ELECTRICAL, BACKSHELL, WITH HEAT-SHRINKABLE STRAIN-RELIEF BOOT (STRAIGHT AND RIGHT ANGLE), THREADED COUPLING |
| MIL-STD-1774 Base Document:1982 | PROCESS FOR CLEANING HYDRAZINE SYSTEMS AND COMPONENTS |
| CSA C22.2 No. 198.1 : 2006 : R2015 | EXTRUDED INSULATING TUBING |
| L-C-530 Revision C:1987 | COATING, PIPE, THERMOPLASTIC RESIN |
| BS EN 62788-1-2:2016 | Measurement procedures for materials used in photovoltaic modules Encapsulants. Measurement of volume resistivity of photovoltaic encapsulants and other polymeric materials |
| MIL-C-27725 Revision B:1969 | COATING, CORROSION PREVENTIVE, FOR AIRCRAFT INTEGRAL FUEL TANKS |
| 07/30083514 DC : 0 | BS EN ISO 21809-3 - PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED AND SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS |
| MIL-HDBK-510-1 Revision A:2010 | AEROSPACE FUELS CERTIFICATION |
| ASTM D 352 : 1997 | Standard Test Methods for Pasted Mica Used in Electrical Insulation |
| UNI EN 16603-20-06 : 2014 | SPACE ENGINEERING - SPACECRAFT CHARGING |
| ASTM D 1304 : 1999 : R2012 | Standard Test Methods for Adhesives Relative to Their Use as Electrical Insulation |
| ASTM C 657 : 1993 : R1998 | Standard Test Method for D-C Volume Resistivity of Glass |
| BS EN ISO 14692-4:2017 | Petroleum and natural gas industries. Glass-reinforced plastics (GRP) piping Fabrication, installation and operation |
| ESD S11.11 : 1993 | SURFACE RESISTANCE MEASUREMENT OF STATIC DISSIPATIVE PLANAR MATERIALS |
| CSA C22.2 No. 0.17 : 2000 : R2004 | EVALUATION OF PROPERTIES OF POLYMERIC MATERIALS |
| ASTM D 5109 : 2012 : REDLINE | Standard Test Methods for Copper-Clad Thermosetting Laminates for Printed Wiring Boards |
| MIL-PRF-8516 Revision G:1997 | SEALING COMPOUND, SYNTHETIC RUBBER, ELECTRIC CONNECTORS AND ELECTRIC SYSTEMS, CHEMICALLY CURED |
| ASTM D 3214 : 1996 | Standard Test Methods for Coating Powders and Their Coatings Used for Electrical Insulation (Withdrawn 2002) |
| PPP-C-1842 Revision B:1992 | CUSHIONING MATERIAL, PLASTIC, OPEN CELL (FOR PACKAGING APPLICATIONS) |
| MIL-A-47315 Revision A:1991 | ADHESIVE, POLYURETHANE |
| MIL-R-45036 Revision D:1978 | RUBBER, HARD,(EBONITE) NATURAL OR SYNTHETIC, SHEET, STRIP, ROD, TUBING AND MOLDED PARTS |
| MIL-PRF-23586 Revision F:1996 | SEALING COMPOUND (WITH ACCELERATOR), SILICONE RUBBER, ELECTRICAL |
| ASTM F 790 : 2008 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM D 2671 : 2013 | Standard Test Methods for Heat-Shrinkable Tubing for Electrical Use |
| ANSI INCITS 126 : 1986 : R2017 | INFORMATION TECHNOLOGY - ONE- AND TWO-SIDED DOUBLE DENSITYUNFORMATTED 5.25 INCH (130 MM) 96 TRACKS PER INCH (3.8 TRACKS PER MM) FLEXIBLE DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 7958 BPR USE |
| CEI EN 62788-1-2 : 1ED 2017 | MEASUREMENT PROCEDURES FOR MATERIALS USED IN PHOTOVOLTAIC MODULES - PART 1-2: ENCAPSULANTS - MEASUREMENT OF VOLUME RESISTIVITY OF PHOTOVOLTAIC ENCAPSULANTS AND OTHER POLYMERIC MATERIALS |
| MIL C 47070 : 0 | COMPOUND, URETHANE |
| ASTM A 947M : 2016 : REDLINE | Standard Specification for Textured Stainless Steel Sheet [Metric] |
| IEEE 95-2002 | IEEE Recommended Practice for Insulation Testing of AC Electric Machinery (2300 V and Above) With High Direct Voltage |
| ASTM D 5205 : 2016 : REDLINE | Standard Classification System and Basis for Specification for Polyetherimide (PEI) Materials |
| ASTM F 79 : 1969 : R1995 : EDT 1 | Standard Specification for Type 101 Sealing Glass |
| SAE AMS 8660 : 2018 | SILICONE COMPOUND NATO CODE NUMBER S-736 |
| ASTM D 709 : 2017 : REDLINE | Standard Specification for Laminated Thermosetting Materials |
| SAE AMS 3359 : 2016 | SILICONE POTTING COMPOUND, ELASTOMERIC TWO-PART, GENERAL PURPOSE 200 TO 400 POISES (20 TO 40 PAS) VISCOSITY |
| ANSI INCITS 162 : 1988 : R2004 | INFORMATION SYSTEMS - TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 5.25-INCH (130-MM), 96-TPI (3,8 TPMM), FLEXIBLE DISK CARTRIDGE FOR 13 262 FTPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| NFPA 69 : 2014 | EXPLOSION PREVENTION SYSTEMS |
| ASTM D 4496 : 2013 | Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials |
| CAN/CSA-Z662-15 | Oil and gas pipeline systems |
| ISO 18797-1:2016 | Petroleum, petrochemical and natural gas industries — External corrosion protection of risers by coatings and linings — Part 1: Elastomeric coating systems-polychloroprene or EPDM |
| ASTM D 5204 : 2017 : REDLINE | CLASSIFICATION SYSTEM FOR POLYAMIDE-IMIDE (PAI) MOLDING AND EXTRUSION MATERIALS |
| ASTM D 2633 : 2013-03 | TEST METHODS FOR THERMOPLASTIC INSULATIONS AND JACKETS FOR WIRE AND CABLE |
| ASTM F 602 : 2009 : R2014 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
| ASTM D 7193 : 2017 : REDLINE | Standard Specification for Unsintered Pigmented Polytetrafluoroethylene (PTFE) Extruded Film or Tape |
| ASTM D 876 : 2013 : REDLINE | Standard Test Methods for Nonrigid Vinyl Chloride Polymer Tubing Used for Electrical Insulation |
| SAE AMS 3666 : 2012 | POLYTETRAFLUOROETHYLENE (PTFE) SHEET, GLASS CLOTH REINFORCED |
| ASTM D 7201 : 2006 | Standard Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in the Workplace, by Phase Contrast Microscopy (with and Option of Transmission Electron Microscopy) |
| ASTM D 3004 : 2008 : R2013 | Standard Specification for Crosslinked and Thermoplastic Extruded Semi-Conducting, Conductor and Insulation Shielding Materials |
| ASTM F 79 : 1969 : R2005 | Standard Specification for Type 101 Sealing Glass |
| ASTM D 6411/D6411M : 1999 : R2012 | Standard Specification For Silicone Rubber Room Temperature Vulcanizing Low Outgassing Materials |
| ASTM D 4732 : 2013 : REDLINE | Standard Specification for Cool-Application Filling Compounds for Telecommunications Wire and Cable |
| ISO 21809-3:2016 | Petroleum and natural gas industries — External coatings for buried or submerged pipelines used in pipeline transportation systems — Part 3: Field joint coatings |
| ASTM F 79 : 1969 : R2010 | Standard Specification for Type 101 Sealing Glass |
| CSA C22.2 No. 144.1 : 2016 | GROUND-FAULT CIRCUIT-INTERRUPTERS |
| NASA HDBK 4002 : 2011 | MITIGATING IN-SPACE CHARGING EFFECTS - A GUIDELINE |
| NASA KSC SPEC E 0029 : 1972 | COMPOUND, POTTING AND MOLDING ELASTOMERIC, SPECIFICATION FOR |
| CSA S806: 2012 | DESIGN AND CONSTRUCTION OF BUILDING STRUCTURES WITH FIBRE-REINFORCED POLYMERS |
| UNI EN ISO 21178 : 2013 | LIGHT CONVEYOR BELTS - DETERMINATION OF ELECTRICAL RESISTANCES |
| UL 943:5ED 2016-05 | Ground-Fault Circuit-Interrupters |
| CSA C22.2 No. 198.3:2005 | COATED ELECTRICAL SLEEVING |
| S806-12 (R2017) | Design and construction of building structures with fibre-reinforced polymers |
| EN 16603-20-06:2014 | Space engineering - Spacecraft charging |
| UNI EN 14617-13 : 2013 | AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY |
| IPC SM 817 : A | GENERAL REQUIREMENTS FOR DIELECTRIC SURFACE MOUNTING ADHESIVES |
| SAE AMS 3732 : 2015 | POTTING COMPOUND, EPOXY ONE PART, FILLED, HEAT CURE, LOW CTE |
| IEEE DRAFT 43 : 1995 | DRAFT RECOMMENDED PRACTICE FOR TESTING INSULATION RESISTANCE OF ROTATING MACHINERY |
| ASTM F 105 : 1972 : R2005 | Standard Specification for Type 58 Borosilicate Sealing Glass |
| SAE AMS 3650 : 2012 | RODS, SHEETS, AND MOLDED SHAPES, POLYCHLOROTRIFLURORETHYNEN (PCTFE) UNPLASTICIZED |
| I.S. EN ISO 21809-3:2016 | PETROLEUM AND NATURAL GAS INDUSTRIES - EXTERNAL COATINGS FOR BURIED OR SUBMERGED PIPELINES USED IN PIPELINE TRANSPORTATION SYSTEMS - PART 3: FIELD JOINT COATINGS (ISO 21809-3:2016) |
| ASTM D 3664 : 2016 : REDLINE | Standard Specification for Biaxially Oriented Polymeric Resin Film for Capacitors in Electrical Equipment |
| MIL F 87260 : 0 | FOAM MATERIAL, EXPLOSION SUPPRESSION, INHERENTLY ELECTRICALLY CONDUCTIVE, FOR AIRCRAFT FUEL TANK & DRY BAY AREAS |
| BS EN 16603-20-06:2014 | Space engineering. Spacecraft charging |
| ASTM C 657 : 1993 : R2013 | Standard Test Method for D-C Volume Resistivity of Glass |
| MIL-P-46112 Revision B:1977 | PLASTIC SHEET & STRIP, POLYMIDE |
| MIL-T-47023 Base Document:1974 | TAPE, HEAT SHRINKABLE |
| MIL-DTL-32011 Base Document:1997 | IGNITION DEVICE, PVU-8/A |
| MIL-I-46865 Revision B:1991 | INSULATING COMPOUND, ELECTRICAL, EPOXY, COLLOIDAL SILICA FILLED FOR POTTING AND ENCAPSULATION |
| ASTM D 5047 : 2017 : REDLINE | Standard Specification for Polyethylene Terephthalate Film and Sheeting |
| ANSI INCITS 125 : 1985 : R2006 | TWO-SIDED, DOUBLE-DENSITY, UNFORMATTED, 5.25 INCH (130-MM), 48-TPI (1,9-TPMM), FLEXIBLE DISK CARTRIDGE FOR 7958 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| MIL-T-47052 Base Document:1974 | TAPE, EPOXY-GLASS CLOTH, THERMOSETTING, PRESSURE SENSITIVE ADHESIVE |
| IPC J STD 030 : A | SELECTION AND APPLICATION OF BOARD LEVEL UNDERFILL MATERIALS |
| IEEE 1133-1988 | IEEE Application Guide for Evaluating Nonceramic Materials for High-Voltage Outdoor Applications |
| BS EN ISO 21809-3:2016 | Petroleum and natural gas industries. External coatings for buried or submerged pipelines used in pipeline transportation systems Field joint coatings |
| MIL-C-46866 Base Document:1973 | COMPOUND, EPOXY MOLDING AND APPLICATION OF |
| MIL-PRF-87260 Revision B:2006 | Foam Material, Explosion Suppression, Inherently Electrostatically Conductive, for Aircraft Fuel Tanks |
| ASTM F 2468 : 2005 | Standard Classification for Specifying Silicone Adhesives and Sealants for Transportation Applications |
| ASTM D 7200 : 2012 : REDLINE | Standard Practice for Sampling and Counting Airborne Fibers, Including Asbestos Fibers, in Mines and Quarries, by Phase Contrast Microscopy and Transmission Electron Microscopy |
| ASTM D 1636 : 2013 : REDLINE | Standard Specification for Allyl Molding Compounds |
| ASTM F 624 : 2009 | Standard Guide for Evaluation of Thermoplastic Polyurethane Solids and Solutions for Biomedical Applications |
| MIL-I-24768 Base Document:1992 | INSULATION, PLASTICS, LAMINATED, THERMOSETTING, GENERAL SPECIFICATION FOR |
| 02/713763 DC : DRAFT DEC 2002 | ISO 15840 - SHIPS AND MARINE TECHNOLOGY - STANDARD SPECIFICATION FOR THERMOSETTING RESIN FIBREGLASS PIPE AND FITTINGS TO BE USED FOR MARINE APPLICATIONS |
| CEI EN 61189-5-503 : 1ED 2017 | TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARD AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 5-503: GENERAL TEST METHOD FOR MATERIALS AND ASSEMBLIES - CONDUCTIVE ANODIC FILAMENTS (CAF) TESTING OF CIRCUIT BOARDS |
| MIL-C-47118 Revision A:1979 | COATING, CONDUCTIVE LACQUER |
| BS IEC 61340-4-8:2010 | Electrostatics Standard test methods for specific applications. Discharge shielding. Bags |
| ASTM D 352 : 1997 : R2008 : EDT 1 | Standard Test Methods for Pasted Mica Used in Electrical Insulation |
| ADS-13F-HDBK : 1997 | AERONAUTICAL DESIGN STANDARD - HANDBOOK - AIR VEHICLE MATERIALS AND PROCESSES |
| BS EN 16603-35-06:2014 | Space engineering. Cleanliness requirements for spacecraft propulsion hardware |
| ASTM D 2341 : 1981 | Specification for Rigid Urethane Foam (Withdrawn 1988) |
| ASTM D 3222 : 2005 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| CSA C22.2 No. 144 : 1991 : R2011 | GROUND FAULT CIRCUIT INTERRUPTERS |
| ASTM F 1837M : 1997 | Standard Specification for Heat-Shrink Cable Entry Seals (Metric) |
| MIL-I-47049 Base Document:1974 | INSULATION TUBING, SILICONE RUBBER, HEAT SHRINKABLE |
| MIL-A-47280 Base Document:1974 | ADHESIVES, EPOXY |
| CSA HGV 4.2 : 2013 | HOSES FOR COMPRESSED HYDROGEN FUEL STATIONS, DISPENSERS AND VEHICLE FUEL SYSTEMS |
| ANSI INCITS 125 : 1985 : R2001 | TWO-SIDED, DOUBLE-DENSITY, UNFORMATTED, 5.25 INCH (130-MM), 48-TPI (1,9-TPMM), FLEXIBLE DISK CARTRIDGE FOR 7958 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| ASTM D 2768 : 1995 : R2001 | Standard Specification for General-Purpose Ethylene-Propylene Rubber Jacket for Wire and Cable (Withdrawn 2007) |
| ASTM D 4969 : 2017 : REDLINE | Standard Specification for Polytetrafluoroethylene–(PTFE) Coated Glass Fabric |
| IEEE C135.90-2014 | IEEE Standard for Pole Line Hardware for Overhead Line Construction |
| CSA C22.2 No. 144 : 1991 | GROUND FAULT CIRCUIT INTERRUPTERS |
| BS PD IEC TS 60079-32-1 : 2013 | EXPLOSIVE ATMOSPHERES - PART 32-1: ELECTROSTATIC HAZARDS, GUIDANCE |
| I.S. EN 61189-5-503:2017 | TEST METHODS FOR ELECTRICAL MATERIALS, PRINTED BOARD AND OTHER INTERCONNECTION STRUCTURES AND ASSEMBLIES - PART 5-503: GENERAL TEST METHOD FOR MATERIALS AND ASSEMBLIES - CONDUCTIVE ANODIC FILAMENTS (CAF) TESTING OF CIRCUIT BOARDS |
| ASTM F 1837M : 1997 : R2002 | Standard Specification for Heat-Shrink Cable Entry Seals (Metric) |
| ASTM F 105 : 1972 : R1995 : EDT 1 | Standard Specification for Type 58 Borosilicate Sealing Glass |
| ASTM D 3222 : 2005 : R2010 | Standard Specification for Unmodified Poly(Vinylidene Fluoride) (PVDF) Molding Extrusion and Coating Materials |
| ASTM D 352 : 1997 : R2003 | Standard Test Methods for Pasted Mica Used in Electrical Insulation |
| ASTM F 665 : 2009 | Standard Classification for Vinyl Chloride Plastics Used in Biomedical Application |
| ASTM D 2413 : 2016 : REDLINE | Standard Practice for Preparation of Insulating Paper and Board Impregnated with a Liquid Dielectric |
| UNE-EN 62788-1-2:2017 | Measurement procedures for materials used in photovoltaic modules - Part 1-2: Encapsulants - Measurement of volume resistivity of photovoltaic encapsulants and other polymeric materials |
| ASTM D 4325 : 2013 : REDLINE | Standard Test Methods for Nonmetallic Semi-Conducting and Electrically Insulating Rubber Tapes |
| CSA C22.2 No. 198.1 : 2006 | EXTRUDED INSULATING TUBING |
| CSA C22.2 No. 144 : 1991 : R2006 | GROUND FAULT CIRCUIT INTERRUPTERS |
| EN ISO 14692-4:2017 | Petroleum and natural gas industries - Glass-reinforced plastics (GRP) piping - Part 4: Fabrication, installation and operation (ISO 14692-4:2017) |
| IEC 61340-4-10:2012 | Electrostatics - Part 4-10: Standard test methods for specific applications - Two-point resistance measurement |
| GOST 849:2018 | Primary nickel. SpecificationsE |
| ISO 21178:2013 | Light conveyor belts Determination of electrical resistances |
| DIN EN 14617-13 E : 2013 | AGGLOMERATED STONE - TEST METHODS - PART 13: DETERMINATION OF ELECTRICAL RESISTIVITY |
| EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| BS EN 1637:1999 | Light conveyor belts. Test methods for the measurement of the electrical resistances |
| EN ISO 21178:2013 | Light conveyor belts - Determination of electrical resistances (ISO 21178:2013) |
| I.S. EN ISO 21178:2013 | LIGHT CONVEYOR BELTS - DETERMINATION OF ELECTRICAL RESISTANCES (ISO 21178:2013) |
| MIL-I-15265 Revision C:1992 | INSULATION, ELECTRICAL, PLASTIC (SUBMARINE BUS BAR COVERING) |
| BS EN ISO 21178:2013 | Light conveyor belts. Determination of electrical resistances |
| UNE-EN 14617-13:2013 | Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity |
| EN 14617-13:2013 | Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity |
| EN 16603-35-06:2014 | Space engineering - Cleanliness requirements for spacecraft propulsion hardware |
| ASTM D 2442 : 1975 : R1996 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| ASTM F 636 : 1985 : R1991 | Guide for Selection of Tests for Material Properties of Transfer Molding Compounds for Electronic and Microelectronic Encapsulation (Withdrawn 1996) |
| I.S. EN 61122:1994 | STILL VIDEO FLOPPY DISK MAGNETIC RECORDING SYSTEM |
| MIL-C-47175 Revision A:1980 | Compound, Polyurethane, for Conformal Coating of Electronic Circuitry |
| MIL C 47027 : 0 | COMPOUND, MOLDING, PLASTIC, RIGID, THERMOPLASTIC |
| MIL-STD-648 Revision E:2016 | Specialized Shipping Containers |
| MIL S 23586 : E | SEALING COMPOUND, ELECTRICAL, SILICONE RUBBER, ACCELERATOR REQUIRED |
| CSA HGV 4.4 : 2013(R2018) | STANDARD FOR BREAKAWAY DEVICES FOR COMPRESSED HYDROGEN DISPENSING HOSES AND SYSTEMS |
| SAE AMS 3731 : 2016 | POTTING COMPOUND, EPOXY, BISPHENOL A-TYPE |
| DOD HDBK 263 : LATEST | ELECTROSTATIC DISCHARGE CONTROL HANDBOOK FOR PROTECTION OF ELECTRICAL AND ELECTRONIC PARTS, ASSEMBLIES AND EQUIPMENT (EXCLUDING ELECTRICALLY INITIATED EXPLOSIVE DEVICES)METRIC |
| L-P-380 Revision C:1973 | PLASTIC MOLDING MATERIAL METHACRYLATE |
| SAE AS 8660 : 1999 | SILICONE COMPOUND NATO CODE NUMBER S-736 |
| ABS 0063 : 2018 COR 2018 | RULES FOR BUILDING AND CLASSING FACILITIES ON OFFSHORE INSTALLATIONS |
| NACE RP 03 03 : 2003 | FIELD-APPLIED HEAT-SHRINKABLE SLEEVES FOR PIPELINES: APPLICATION, PERFORMANCE, AND QUALITY CONTROL |
| MIL-I-21070 Revision B:1965 | INSULATING SHEET AND TAPE, ELECTRICAL, REINFORCED MICA PAPER |
| MIL-A-47040 Base Document:1974 | ADHESIVE-SEALANT, SILICONE, RTV, HIGH TEMPERATURE |
| ASTM F 604 : 1994 | Specification for Silicone Elastomers Used in Medical Applications (Withdrawn 2001) |
| MIL P 47241 : 0 | PRIMER, POLYURETHANE, ONE PART |
| ASTM F 105 : 1972 : R2015 | Standard Specification for Type 58 Borosilicate Sealing Glass |
| MIL-R-47025 Revision A:1991 | RESIN, CASTING, FIRE RETARDANT, EPOXY BASE |
| ANSI INCITS 121 : 1984 : R2001 | TWO-SIDED, UNFORMATTED, 8-INCH (200-MM), 48-TPI, DOUBLE-DENSITY, FLEXIBLE, DISK CARTRIDGE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS FOR 13 262 FTPR TWO-HEADED APPLICATION |
| ASTM F 641 : 2009 : R2014 | Standard Specification for Implantable Epoxy Electronic Encapsulants |
| ANSI INCITS 171 : 1989 : R2000 | ONE- AND TWO-SIDED, HIGH-DENSITY, UNFORMATTED, 90-MM (3.5 IN), 5,3-TPMM (135-TPI) FLEXIBLE DISK CARTRIDGE FOR 15916 BPR USE - GENERAL, PHYSICAL, AND MAGNETIC REQUIREMENTS |
| MIL-C-47121 Base Document:1974 | COMPOUND, SEALING, POLYSULFIDE RUBBER |
| MIL-P-46184 Base Document:1982 | PLASTIC MOLDING & EXTRUSION MATERIAL, POLYETHERIMIDE (PEI) |
| BS ISO 15840:2004 | Ships and marine technology. Standard specification for thermosetting resin fibreglass pipe and fittings to be used for marine applications |
| SAE AS 5258 : 2012 | INSULATING COMPONENT, MOLDED, ELECTRICAL, HEAT SHRINKABLE, CONNECTOR AND CABLE ACCESSORY, SEALING STRAIN RELIEF, GENERAL SPECIFICATION FOR |
| CSA C22.2 No. 144 : 1991 : R2015 | GROUND FAULT CIRCUIT INTERRUPTERS |
| SAE AS 81765 : 2017 | INSULATING COMPONENTS, MOLDED, ELECTRICAL, HEAT SHRINKABLE, GENERAL SPECIFICATION FOR |
| NASA STD 4005(INT) : 2006 | LOW EARTH ORBIT SPACECRAFT CHARGING DESIGN STANDARD |
| ANSI INCITS 137 : 1988 | INFORMATION TECHNOLOGY - ONE- AND TWO-SIDED, UNFORMATTED, 90-MM (3.5-IN) 5,3-TPMM (135-TPI), FLEXIBLE DISK CARTRIDGE FOR 7958 BPR USE - GENERAL, PHYSICAL AND MAGNETIC REQUIREMENTS |
| MIL-R-47211 Revision A:1989 | RUBBER, SILICONE, ROOM TEMPERATURE CURING |
| BS EN ISO 18797-1:2017 | Petroleum, petrochemical and natural gas industries. External corrosion protection of risers by coatings and linings Elastomeric coating systems-polychloroprene or EPDM |
| CSA HGV 4.5 : 2013 | STANDARD FOR PRIORITY AND SEQUENCING EQUIPMENT FOR HYDROGEN VEHICLE FUELING |
| SAE AMS 2487 : 2018 | ANODIC TREATMENT OF TITANIUM AND TITANIUM ALLOYS SOLUTION PH 12.4 MAXIMUM |
| I.S. EN ISO 14692-4:2017 | PETROLEUM AND NATURAL GAS INDUSTRIES - GLASS-REINFORCED PLASTICS (GRP) PIPING - PART 4: FABRICATION, INSTALLATION AND OPERATION (ISO 14692-4:2017) |
| NFPA 655 : 2017 | PREVENTION OF SULFUR FIRES AND EXPLOSIONS |
| I.S. EN 16603-20-06:2014 | SPACE ENGINEERING - SPACECRAFT CHARGING |
| IEEE 1523-2002 | IEEE Guide for the Application, Maintenance, and Evaluation of Room Temperature Vulcanizing (RTV) Silicone Rubber Coatings for Outdoor Ceramic Insulators |
| UNE-EN ISO 21809-3:2016 | Petroleum and natural gas industries - External coatings for buried or submerged pipelines used in pipeline transportation systems - Part 3: Field joint coatings (ISO 21809-3:2016) |
| I.S. EN IEC 62688:2018 | CONCENTRATOR PHOTOVOLTAIC (CPV) MODULES AND ASSEMBLIES - SAFETY QUALIFICATION |
| ASTM F 790 : 2008 : R2013 | Standard Guide for Testing Materials for Aerospace Plastic Transparent Enclosures |
| ASTM F 602 : 2009 : R2015 | Standard Criteria for Implantable Thermoset Epoxy Plastics |
| ASTM D 2768 : 1995 | Standard Specification for General-Purpose Ethylene-Propylene Rubber Jacket for Wire and Cable |
| ASTM D 2442 : 1975 : R2007 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| ASTM D 8033 : 2016 | Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials |
| ASTM D 2442 : 1975 : R2016 | Standard Specification for Alumina Ceramics for Electrical and Electronic Applications |
| CLC/TR 60079-32-1:2015 | Explosive atmospheres - Part 32-1: Electrostatic Hazards - Guidance |
| ASTM D 729 : 1995 | Standard Specification for Vinylidene Chloride Molding Compounds (Withdrawn 2000) |
| ASTM D 470 : 2013 : REDLINE | Standard Test Methods for Crosslinked Insulations and Jackets for Wire and Cable |
| ASTM D 6224 : 2016 : REDLINE | Standard Practice for In-Service Monitoring of Lubricating Oil for Auxiliary Power Plant Equipment |
| ASTM F 1109 : 1987 | Specification for Porous Composites of Polytetrafluoroethylene and Carbon for Surgical Implant Applications (Withdrawn 1993) |
| ASTM D 4872 : 2014 : REDLINE | Standard Test Method for Dielectric Testing of Wire and Cable Filling Compounds |
| ASTM D 352 : 1997 : R2016 | Standard Test Methods for Pasted Mica Used in Electrical Insulation |
| ASTM D 116 : 1986 : R1999 | Standard Test Methods for Vitrified Ceramic Materials for Electrical Applications |
| ASTM D 1000 : 2017 : REDLINE | Standard Test Methods for Pressure-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applications |
| DIN EN ISO 21178 E : 2013 | LIGHT CONVEYOR BELTS - DETERMINATION OF ELECTRICAL RESISTANCES (ISO 21178:2013) |
| IEEE 789-2013 | IEEE Standard Performance Requirements for Communications and Control Cables for Application in High-Voltage Environments |
| BS EN 14617-13:2013 | Agglomerated stone. Test methods Determination of electrical resistivity |
| IEC 62788-1-2:2016 | Measurement procedures for materials used in photovoltaic modules - Part 1-2: Encapsulants - Measurement of volume resistivity of photovoltaic encapsulants and other polymeric materials |
| EN 61122:1993 | Still video floppy disk magnetic recording system |
| DIN EN 14617-13:2013-06 | Agglomerated stone - Test methods - Part 13: Determination of electrical resistivity |
| ASTM D 4496 : 2013 | Standard Test Method for D-C Resistance or Conductance of Moderately Conductive Materials |
| ASTM D 1711 : 2015 : REDLINE | Standard Terminology Relating to Electrical Insulation |
| ASTM E 104 : 2002 | Standard Practice for Maintaining Constant Relative Humidity by Means of Aqueous Solutions |
| ASTM D 374 : 1999 | Standard Test Methods for Thickness of Solid Electrical Insulation |
US$83.00
Excluding Tax where applicable
USD
CAD
CHF
CNY
DKK
EUR
GBP
HKD
IDR
INR
JPY
KRW
MXN
NOK
NZD
SEK
SGD
USD
ZAR
PDF - English
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
Please Login or Create an Account so you can add users to your Multi user PDF Later.
Important note : All end users must be registered with an Account prior to user licenses being assigned.
Users cannot be edited or removed once added to your Multi user PDF.
Access your standards online with a subscription
Features
-
Simple online access to standards, technical information and regulations.
-
Critical updates of standards and customisable alerts and notifications.
-
Multi-user online standards collection: secure, flexible and cost effective.