• There are no items in your cart

ASTM D 2673 : 2014

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Specification for Oriented Polypropylene Film
Available format(s)

Hardcopy , PDF

Superseded date

04-28-2022

Language(s)

English

Published date

09-11-2014

1.1This specification covers oriented polypropylene (OPP) film in the thickness range from 10 to 75 μm (0.4 to 3.0 mils).

1.2The film can contain colorants, stabilizers, or other additives, and can be coated for the improvement of performance properties (heat sealability, gas permeability, and so forth).

1.3The film can be annealed (heat-set) to reduce the unrestrained linear shrinkage and shrink tension on exposure to heat.

1.4The values stated in SI units are to be regarded as standard. The values given in parentheses are for information only.

1.5The following safety hazards caveat pertains only to the test methods portion, Section 7, of this specification: This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

Note 1:There is no known ISO equivalent to this standard.

Committee
D 20
DocumentType
Standard
Pages
4
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 2732 : 2008 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM D 1746 : 1997 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 4101 : 2001 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM E 1870 : 2011 Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film
ASTM D 4101 : 2001 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4101 : 2006 : REV B Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4101 : 2005 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 6988 : 2008 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 4101 : 2000 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1894 : 2011 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1922 : 2008 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2578 : 2009 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 4000 : 2013 Standard Classification System for Specifying Plastic Materials
ASTM D 4101 : 2008 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4321 : 2004 Standard Test Method for Package Yield of Plastic Film
ASTM D 2732 : 2014 : R2020 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 3354 : 2008 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 3892 : 2015 : R2020 Standard Practice for Packaging/Packing of Plastics
ASTM D 1434 : 1982 : R2003 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 4101 : 2006 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4101 : 2004 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1003 : 2007 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 4101 : 2014 : EDT 2 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2003 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 6988 : 2021 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 4000 : 2000 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 4101 : 2010 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4101 : 2011 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2012 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 Standard Classification System for Specifying Plastic Materials
ASTM D 4101 : 2005 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1003 : 2013 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM E 96/E96M : 2021 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
ASTM D 4321 : 1999 Standard Test Method for Package Yield of Plastic Film
ASTM D 2838 : 2008 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 1922 : 2015 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2457 : 2008 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2578 : 2008 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 3892 : 1993 : R2003 Standard Practice for Packaging/Packing of Plastics
ASTM D 3892 : 2015 Standard Practice for Packaging/Packing of Plastics
ASTM D 1894 : 2000 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1922 : 2006 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4101 : 2007 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 3985 : 2005 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 5946 : 2004 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 4101 : 2002 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2011 Standard Classification System for Specifying Plastic Materials
ASTM D 1894 : 2001 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 2578 : 1999 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 6988 : 2003 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 5946 : 2009 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 4101 : 2003 : REV B Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 3354 : 2015 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 3892 : 1993 : R1998 Standard Practice for Packaging/Packing of Plastics
ASTM D 2578 : 2017 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 3985 : 2005 : R2010 : EDT 1 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 3985 : 2002 : EDT 1 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 3354 : 1996 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 4101 : 2002 : REV B Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2004 : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 1746 : 2003 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 2732 : 1996 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM D 4321 : 2009 Standard Test Method for Package Yield of Plastic Film
ASTM D 4101 : 2009 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 2732 : 2003 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film and Sheeting
ASTM D 1003 : 2007 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 5946 : 1999 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 4101 : 2006 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1894 : 2014 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting (Withdrawn 2023)
ASTM D 4000 : 2009 : REV B Standard Classification System for Specifying Plastic Materials
ASTM D 1922 : 2003 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4000 : 2000 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2010 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 2457 : 2013 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 4101 : 2004 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4101 : 1982 : R1988 : EDT 1 Standard Specification for Propylene Plastic Injection and Extrusion Materials
ASTM D 4101 : 2017 Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
ASTM D 3354 : 2011 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1894 : 2011 : EDT 1 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 4000 : 2007 Standard Classification System for Specifying Plastic Materials
ASTM D 4000 : 2009 : REV A Standard Classification System for Specifying Plastic Materials
ASTM D 6988 : 2007 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 2838 : 1995 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 5946 : 2001 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM E 96/E96M : 2016 Standard Test Methods for Water Vapor Transmission of Materials
ASTM D 4000 : 2001 Standard Classification System for Specifying Plastic Materials
ASTM D 4101 : 2014 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1003 : 2011 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 4000 : 2008 Standard Classification System for Specifying Plastic Materials
ASTM D 1746 : 2009 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 1922 : 2015 : R2020 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM E 1870 : 2004 Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film
ASTM D 4101 : 2010 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 2578 : 2004 Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 1003 : 2021 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 2457 : 1997 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 1434 : 1982 : R2015 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 618 : 2013 Standard Practice for Conditioning Plastics for Testing
ASTM E 1870 : 2011 : R2019 Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film
ASTM D 1922 : 2003 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 4000 : 2001 : REV A : EDT 1 Standard Classification System for Specifying Plastic Materials
ASTM D 4101 : 2003 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2004 Standard Classification System for Specifying Plastic Materials
ASTM D 3985 : 1995 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 1434 : 1982 : R2009 : EDT 1 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting
ASTM D 4101 : 2003 : REV A Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 6988 : 2013 Standard Guide for Determination of Thickness of Plastic Film Test Specimens
ASTM D 1746 : 2015 Standard Test Method for Transparency of Plastic Sheeting
ASTM D 1003 : 2000 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 5946 : 2017 Standard Test Method for Corona-Treated Polymer Films Using Water Contact Angle Measurements
ASTM D 2732 : 2014 Standard Test Method for Unrestrained Linear Thermal Shrinkage of Plastic Film<brk/> and Sheeting
ASTM D 1922 : 2005 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3892 : 1993 : R2009 Standard Practice for Packaging/Packing of Plastics
ASTM D 4000 : 2010 Standard Classification System for Specifying Plastic Materials
ASTM D 3354 : 2021 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 1894 : 2008 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 2838 : 2009 : EDT 1 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting (Withdrawn 2018)
ASTM D 4101 : 2002 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 2838 : 2007 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 2457 : 2003 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 1003 : 2011 : EDT 1 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM D 1922 : 2000 : REV A Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 3354 : 2004 Standard Test Method for Blocking Load of Plastic Film by the Parallel Plate Method
ASTM D 3985 : 2002 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 4101 : 2017 : EDT 1 Standard Classification System and Basis for Specification for Polypropylene Injection and Extrusion Materials
ASTM D 4000 : 2003 Standard Classification System for Specifying Plastic Materials
ASTM D 1894 : 2006 Standard Test Method for Static and Kinetic Coefficients of Friction of Plastic Film and Sheeting
ASTM D 1003 : 1992 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics
ASTM E 1870 : 1998 Standard Test Method for Odor and Taste Transfer from Polymeric Packaging Film
ASTM D 2838 : 2009 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 3985 : 2017 Standard Test Method for Oxygen Gas Transmission Rate Through Plastic Film and Sheeting Using a Coulometric Sensor
ASTM D 2457 : 2021 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 2457 : 2008 : EDT 1 Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics
ASTM D 4101 : 2014 : EDT 1 Standard Specification for Polypropylene Injection and Extrusion Materials
ASTM D 1922 : 2006 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 2838 : 2002 Standard Test Method for Shrink Tension and Orientation Release Stress of Plastic Film and Thin Sheeting
ASTM D 2578 : 2004 : REV A Standard Test Method for Wetting Tension of Polyethylene and Polypropylene Films
ASTM D 4321 : 2015 Standard Test Method for Package Yield of Plastic Film (Withdrawn 2024)
ASTM D 618 : 2021 Standard Practice for Conditioning Plastics for Testing
ASTM D 1922 : 2009 Standard Test Method for Propagation Tear Resistance of Plastic Film and Thin Sheeting by Pendulum Method
ASTM D 1434 : 1982 : R1998 Standard Test Method for Determining Gas Permeability Characteristics of Plastic Film and Sheeting

View more information
US$66.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.