• There are no items in your cart

ASTM D 3801 : 2019

Superseded
Superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

View Superseded by
superseded

A superseded Standard is one, which is fully replaced by another Standard, which is a new edition of the same Standard.

Standard Test Method for Measuring the Comparative Burning Characteristics of Solid Plastics in a Vertical Position
Available format(s)

Hardcopy , PDF

Superseded date

01-29-2020

Language(s)

English

Published date

01-15-2019

This fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixed flame applied to the base of specimens held in a vertical position.

1.1This fire-test-response standard covers a small-scale laboratory procedure for determining comparative burning characteristics of solid-plastic material, using a 20-mm (50W) premixed flame applied to the base of specimens held in a vertical position.

Note 1:This test method and the 20 mm (50W) Vertical Burning Test (V-0, V-1, or V-2) of ANSI/UL 94 are equivalent.

Note 2:This test method and Test Method B of IEC 60695–11–10 are equivalent. IEC 60695–11–10 has replaced ISO 1210.

Note 3:For additional information on materials that burn up to the holding clamp by this test method, see Test Method D635. For test methods of flexible plastics in the form of thin sheets and film, see Test Method D4804. For additional information on comparative burning characteristics and resistance to burn-through, see Test Method D5048.

1.2This test method was developed for polymeric materials used for parts in devices and appliances. The results are intended to serve as a preliminary indication of their acceptability with respect to flammability for a particular application. The final acceptance of the material is dependent upon its use in complete equipment that conforms with the standards applicable to such equipment.

1.3The classification system described in the appendix is intended for quality assurance and the preselection of component materials for products.

1.4It is possible that this test is applicable to nonmetallic materials other than plastics. Such application is outside the scope of this technical committee.

1.5This test method does not cover plastics when used for building construction, finishing or contents such as wall and floor coverings, furnishings, decorative objects etc. In addition, the fire resistance (in terms of an hourly rating), flame spread, smoke characterization and heat release rate are not evaluated by this test. Other fire tests exist and shall be used to evaluate the flammability of materials in these intended end use product configuration.

1.6The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.7This standard is used to measure and describe the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.8This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Committee
D 20
DocumentType
Test Method
Pages
7
PublisherName
American Society for Testing and Materials
Status
Superseded
SupersededBy
Supersedes

ASTM D 8033 : 2016 Standard Classification System for Poly(Ether Ether Ketone) (PEEK) Molding and Extrusion Materials
ASTM D 6394 : 2014 Standard Specification for Sulfone Plastics (SP)
ASTM D 4976 : 2012 : REV A Standard Specification for Polyethylene Plastics Molding and Extrusion Materials
ASTM D 5025 : 2012 : EDT 1 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 1593 : 2019 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
ASTM D 1593 : 2013 Standard Specification for Nonrigid Vinyl Chloride Plastic Film and Sheeting
ASTM D 5336 : 2015 : REV A Standard Classification System and Basis for Specification for Polyphthalamide (PPA) Injection Molding Material
ASTM D 635 : 2018 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position
ASTM D 8065/D8065M : 2016 Standard Classification System and Basis for Specification for Specifying Plastic Films
ASTM D 4000 : 2016 Standard Classification System for Specifying Plastic Materials
ASTM D 4804 : 2019 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics

ASTM D 5025 : 2012 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 5207 : 2014 Standard Practice for Confirmation of 20–mm (50–W) and 125–mm (500–W) Test Flames for Small-Scale Burning Tests on Plastic Materials
ASTM D 5048 : 2009 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame
ASTM D 5207 : 2009 Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials
ASTM D 5025 : 2005 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 5207 : 1998 Standard Practice for Calibration of 20 and 125 mm Test Flames for Small-Scale Burning Tests on Plastic Materials
ASTM D 4804 : 2019 : REV A Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 5025 : 2012 : EDT 1 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 5048 : 2003 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame
ASTM D 4804 : 2019 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 5025 : 1999 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 5207 : 2003 Standard Practice for Confirmation of 20-mm (50-W) and 125-mm (500-W) Test Flames for Small-Scale Burning Tests on Plastic Materials
ASTM D 4804 : 2003 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 5048 : 2014 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 5025 : 2011 Standard Specification for Laboratory Burner Used for Small-Scale Burning Tests on Plastic Materials
ASTM D 4804 : 1998 Standard Test Methods for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 4804 : 2014 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 5048 : 2019 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using a 125-mm Flame
ASTM D 4804 : 2009 Standard Test Method for Determining the Flammability Characteristics of Nonrigid Solid Plastics
ASTM D 5048 : 1997 Standard Test Method for Measuring the Comparative Burning Characteristics and Resistance to Burn-Through of Solid Plastics Using 125-mm Flame

View more information
US$75.00
Excluding Tax where applicable

Access your standards online with a subscription

Features

  • Simple online access to standards, technical information and regulations.

  • Critical updates of standards and customisable alerts and notifications.

  • Multi-user online standards collection: secure, flexible and cost effective.